Gigabyte GA-7VAXP-A User manual

When you installing AGP card, please make sure the following

notice is fully understood and practiced. If your AGP card has

"AGP 4X/8X(1.5V) notch"(show below), please make sure your AGP

card is AGP 4X/8X(1.5V).

Caution: AGP 2X(3.3V) card is not supported by VIA

®

KT400A. You

might experience system unable to boot up normally. Please insert

an AGP 4X/8X(1.5V) card

Example 1: Diamond Vipper V770 golden finger is compatible with

2X/4X mode AGP slot. It can be switched between AGP 2X(3.3V) or 4X

(1.5V) mode by adjusting the jumper. The factory default for this card is

2X(3.3V).

The GA-7VAX-A / GA-7VAX1394-A / GA-7VAXP-A / GA-7VAXP-A Ultra

motherboards might not function properly, if you install this card without

switching the jumper to 4X(1.5V) mode in it.

Example 2: Some ATi Rage 128 Pro graphics cards made by "Power

Color", the graphics card manufacturer & some SiS 305 cards, their

golden finger is compatible with 2X(3.3V)/4X(1.5V) mode AGP slot, but

they support 2X(3.3V) only.

The GA-7VAX-A / GA-7VAX1394-A / GA-7VAXP-A / GA-7VAXP-A Ultra

motherboards might not function properly, If you install this card in it.

Note : Although Gigabyte's AG32S(G) graphics card is based on

ATi Rage 128 Pro chip, the design of AG32S(G) is compliance

with AGP 4X(1.5V) specification. Therefore, AG32S (G)will work

fine w ith VIA

®

KT400A based motherboards.

Before you install PCI cards, please remove the Dual BIOS

label from PCI slots if there is one.

AGP 4X/8X notch

M The author assumes no responsibility for any errors or

omissions that may appear in this document nor does the

author make a commitment to update the information contained

herein.

M Third-party brands and names are the property of their

respective owners.

M Please do not remove any labels on motherboard, thismay void

the warranty of this motherboard.

M Due to rapid change in technology, some of the specifications

might be out of date before publication of this booklet.

Declaration of Conformity

We, M anufacturer/Importer

(full address)

G.B.T. Technology Träding GMbH

Ausschlager Weg 41, 1F, 20537 Hamburg, Germany

declare that the product

( description of the apparatus, system, installation to which it refers)

Mother Board

GA-7VAX-A / GA-7VAX1394-A / GA-7VAXP-A / GA-7VAXP-A Ultra

is in conformity with

(reference to the specification under w hich conformity is declared)

in accordance with 89/336 EEC-EMC Directive

o EN 55011 Limits and methods of measurement

of radio disturbance characteristics of

industrial,scientific and medical (ISM

high frequency equipment

o EN 61000-3-2*

T EN 60555-2

Disturbances in supply systems cause

by household appliances and similar

electrical equipment “Harmonics”

o EN 55013

Limits and methods of measurement

of radio disturbance characteristics of

broadcast receivers and associated

equipment

o EN 61000-3-3* Disturbances in supply systems cause

by household appliances and similar

electrical equipment “Voltage fluctuations”

o EN 55014 Limits and methods of measurement

of radio disturbance characteristics of

household electrical appliances,

portable tools and similar electrical

apparatus

T EN 50081-1

Generic emission standard Part 1:

Residual commercial and light industry

T EN 50082-1

Generic immunity standard Part 1:

Residual commercial and light industry

o EN 55015 Limits and methods of measurement

of radio disturbance characteristics of

fluorescent lamps and luminaries

Generic emission standard Part 2:

Industrial environment

o EN 55081-2

Immunity from radio interference of

broadcast receivers and associated

equipment

Generic emission standard Part 2:

Industrial environment

o EN 55082-2

T EN 55022 Limits and methods of measurement

of radio disturbance characteristics of

information technology equipment

lmmunity requirements for household

appliances tools and similar apparatus

o ENV 55104

Cabled distribution systems; Equipment

for receiving and/or distr ibution from

sound and television signals

EMC requirements for uninterruptible

power systems (UPS)

o EN50091-2

o EN 55020

o DIN VDE 0855

o part 10

o part 12

(EC conformity marking)

T CE marking

The manufactur er also declares the confor mity of above mentioned product

with the actual requir ed safety standards in accor dance with LVD 73/23 EEC

Safety requirements for mains operated

electronic and related apparatus for

household and similar general use

o EN 60950

o EN 60065

Safety of household and similar

electrical appliances

o EN 60335

Manufacturer/Importer

Signature:

Name:

(Stamp)

Date : April 16, 2003

T EN 60555-3

Timmy Huang

o EN 50091-1

Timmy Huang

Safety for information technology equipment

including electrical bussiness equipment

General and Safety requirments for

uninterruptible power systems (UPS)

FCC Part 15, Subpart B, Section 15.107(a) and Section 15.109(a),

Class B Digital Device

DECLARATION OF CONFORMITY

Per FCC Part 2 Section 2.1077(a)

Responsible PartName:

Address:

Phone/Fax No:

hereby declares that the product

Product Name:

Conforms to the following specifications:

This device complies with part 15 of the FCC Rules. Operation is

subject to the following two conditions: (1) This device may not

cause harmful and (2) this device must accept any inference received,

including that may cause undesired operation.

Representative Person’s Name:

Signature:

Eric Lu

Supplementary Information:

Model Number:

17358 Railroad Street

City of Industry, CA 91748

G.B.T. INC. (U.S.A.)

(818) 854-9338/ (818) 854-9339

Motherboard

GA-7VAX-A / GA-7VAX1394-A /

GA-7VAXP-A / GA-7VAXP-A Ultra

Date:

ERIC LU

April 16 ,2003

USER'S MANUAL

KT400A Series

AMD Socket A Processor Motherboard

AMD Athlon

™

/ Athlon

™

XP / Duron

™

Socket A Processor Motherboard

Rev. 1002

12ME-7VAXPAU-1002

- 2 -KT400A Series Motherboard

English

Table of Content

Item Checklist ......................................................................................4

WARNING! ..........................................................................................4

Chapter 1 Introduction .........................................................................5

Features Summary .......................................................................................... 5

KT400A Series Motherboard Layout .............................................................. 8

Block Diagramt ............................................................................... 9

Chapter 2 Hardware Installation Process ............................................ 11

Step 1: Install the Central Processing Unit (CPU) ....................................... 12

Step1-1: CPU Speed Setup .......................................................................... 12

Step1-2: CPU Installation ............................................................................. 13

Step1-3:CPU Heat Sink Installation .............................................................. 14

Step 2: Install memory modules ................................................................... 15

Step 3: Install expansion cards ..................................................................... 17

Step 4: Connect ribbon cables, cabinet wires, and power supply .............. 18

Step 4-1 : I/O Back Panel Introduction .......................................................... 18

Step 4-2 : Connectors & Jumper Setting Introduction .................................... 20

Chapter 3 BIOS Setup ....................................................................... 35

The Main Menu (For example: BIOS Ver. :E2) ............................................ 36

Standard CMOS Features ............................................................................. 38

Advanced BIOS Features.............................................................................. 41

Integrated Peripherals ................................................................................... 43

Table of Content

English

- 3 -

Power Management Setup ............................................................................ 48

PnP/PCI Configurations................................................................................. 51

PC Health Status ........................................................................................... 52

Frequency/Voltage Control ............................................................................ 54

Top Performance............................................................................................ 56

Load Fail-Safe Defaults ................................................................................. 57

Load Optimized Defaults ............................................................................... 58

Set Supervisor/User Password ..................................................................... 59

Save & Exit Setup .......................................................................................... 60

Exit Without Saving ...................................................................................... 61

Chapter 4 Technical Reference .......................................................... 63

BIOS Flash PRocedure ................................................................................. 63

@ BIOS Introduction ...................................................................................... 83

Easy Tune 4

TM

Introduction ........................................................................... 84

2-/4-/6-Channel Audio Function Introduction ............................................... 85

Chapter 5 Appendix ........................................................................... 93

- 4 -KT400A Series Motherboard

English

Item Checklist

Computer motherboards and expansion cards contain very delicate Integrated Circuit

(IC) chips. To protect them against damage from static electricity, you should follow

some precautions whenever you work on your computer.

1. Unplug your computer when working on the inside.

2. Use a grounded wrist strap before handling computer components. If you do not have

one, touch both of your hands to a safely grounded object or to a metal object, such as

the power supply case.

3. Hold components by the edges and try not touch the IC chips, leads or connectors, or

other components.

4. Place components on a grounded antistatic pad or on the bag that came with the

components whenever the components are separated from the system.

5. Ensure that the ATX power supply is switched off before you plug in or remove the ATX

Power connector on the m otherboard.

If the motherboard has mounting holes, but they don’t line up with the holes on the base and there

are no slots to attach the spacers, do not become alarmed you can still attach the spacers to the

mounting holes. Just cut the bottom portion of the spacers (the spacer may be a little hard to cut off, so

be careful of your hands). In this way you can still attach the motherboard to the base without worrying

about short circuits. Sometimes you may need to use the plastic springs to isolate the screw from the

motherboard PCB surface, because the circuit wire may be near by the hole. Be careful, don't let the

screw contact any printed circuit write or parts on the PCB that are near the fixing hole, otherwise it may

damage the board or cause board malfunctioning.

Installing the motherboard to the chassis…

þ The KT400A Series motherboard þ RAID Manual **

þ IDE cable x 1/ Floppy cable x 1 þ 2 Port USB Cable x 2

þ IDE cable x 2 ** þ Audio combo Kit x1 **

þ CD for motherboard driver & utility þ IEEE 1394 Cable x1 ***

þ KT400A Series user’s manual o SPD Kit x1

þ I/O Shield þ Quick PC Installation Guide

þ Motherboard Settings Label þ SATA RAID Manual *

þ SATA cable x 2 * o GC-SATA Card * (Optional)

(Manual ; SATA cable x1 ; Power cable x 1)

" * " FOR GA-7VAXP-A Ultra Only.

" ** " FOR GA-7VAXP-A Ultra / GA-7VAXP-A Only.

" *** " For GA-7VAXP-A Ultra / GA-7VAXP-A / GA-7VAX1394-A Only.

Introduction- 5 -

English

Form Factor — 30.5cm x 24.4cm ATX size form factor, 4 layers PCB.

Motherboard — KT400A Series:

GA-7VAX-A / GA-7VAX1394-A / GA-7VAXP-A / GA-7VAXP Ultra-A

CPU — Socket A processor

AMD Athlon

TM

/Athlon

TM

XP/ Duron

TM

(K7)

128K L1 & 512K/256K/64K L2 cache on die

200/266/333MHz FSB and DDR bus speeds

— Supports 1.4GHz and faster

Chipset — VIA KT400A Memory/AGP/PCI Controller (PAC)

— VIA VT8235 Integrated Peripheral Controller (PSIPC)

Memory — 3 184-pin DDR sockets

— Supports DDR DRAM PC2100/PC2700/PC3200

— Supports up to 3.0GB DDR (Max)

— Supports only 2.5V DDR DIMM

I/O Control — IT8705

Sl ots — 1 AGP slot su pports 8 X/4X m ode(1.5V ) & AGP 3.0 Comp liant

— 5 PCI slots supports 33MHz & PCI 2.2 compliant

On-Board IDE — 2 IDE controllers provides IDE HDD/CD-ROM (IDE1, IDE2) with

PIO, Bus Master (Ultra DMA33/ATA66/ATA100/ATA133)

operation modes.

— IDE3 and IDE4 Compatible with RAID,Ultra ATA133/100, EIDE **

Hardware Monitor — CPU/System Fan Revolution detect

— CPU/System temperature detect

— System Voltage Detect

— Thermal shutdown function

Features Summary

to be continued......

" ** " FOR GA-7VAXP-A Ultra / GA-7VAXP-A Only.

" *** " For GA-7VAXP-A Ultra / GA-7VAXP-A / GA-7VAX1394-A Only.

Chapter 1 Introduction

- 6 -KT400A Series Motherboard

English

" * " FOR GA-7VAXP-A Ultra Only.

" ** " FOR GA-7VAXP-A Ultra / GA-7VAXP-A Only.

" *** " For GA-7VAXP-A Ultra / GA-7VAXP-A / GA-7VAX1394-A Only.

On-Board Peripherals — 1 Floppy port supports 2 FDD with 360K, 720K,1.2M, 1.44M

and 2.88M bytes.

— 1 Parallel port supports Normal/EPP/ECP mode

— 2 Serial port (COMA & COMB)

— 6 x USB 2.0/1.1 (4 by cable)

— 3 x IEEE1394 by cable ***

— 1 IrDA connector for IR

— 1 Smart Card Reader connector for SCR

On-Board Sound — Realtek ALC650 CODEC

— Line Out / 2 front speaker

— Line In / 2 rear speaker(by s/w switch)

— Mic In / center& subwoofer(by s/w switch)

— SPDIF Out /SPDIF In

— CD In / AUX In / Game port

On-Board USB 2.0 — Built in VIA VT8235 Chipset

On-Board RAID ** — Onbard Promise PDC20276

— Supports data striping (RAID 0) or mirroring (RAID 1)

— Supports concurrent dual IDE controller operation

— Supports IDE bus master operation

— Displays status and error checking messages during boot-up

— Mirroring supports automatic background rebuilds

— Features LBA and Extended Interrupt 13 drive translation in

controller onboard BIOS

On-Board SATA RAID * — Onboard Silicon Image Sil3112A

— Supports Disk striping (RAID0) or DISK Mirroring (RAID1)

— Supports UDMA up to 150 MB/sec

— AIL UDMA and PIO Modes

— Up to 2 SATA Device

— ACPI and ATA/ATAPI6

Introduction- 7 -

English

Please set the CPU host frequency in accordance with your processor's specifications.

We don't recommend you to set the system bus frequency over the CPU's specification

because these specific bus frequencies are not the standard specifications for CPU,

chipset and most of the peripherals. Whether your system can run under these specific

bus frequencies properly will depend on your hardware configurations, including CPU,

Chipsets,SDRAM,Cards… .etc.

On-Board LAN — RealTek RTL8100BL

On-Board IEEE1394 *** — VT6306

PS/2 Connector — PS/2 Keyboard interface and PS/2 Mouse interace

BIOS — Licensed Award BIOS, 2M bit flash ROM

— Supports Dual BIOS /Q-Flash

Additional Features — PS/2 Keyboard power on by password,PS/2 Mouse power on

— External Modem wake up

— STR(Suspend-To-RAM)

— Wake on LAN (WOL)

— AC Recovery

— Poly fuse for keyboard over-current protection

— USB KB/Mouse wake up from S3

— Support Thermal shutdown function

— Supports @BIOS

— Supports EasyTune 4

Overclocking — Over Voltage (DDR/AGP/CPU) by BIOS

— Over Clock (DDR/AGP/CPU/PCI) by BIOS

- 8 -KT400A Series Motherboard

English

KT400A Series Motherboard Layout

GA-7VAXP-A Ultra

KB_MS

CK_RATIO

COMA

LPTGAM E

LINE_OUTMIC_IN

USB

IT8705

AC 97

BATTERY

Backup

BIOS

SYS

FAN

VT8235

VIA KT400A

SOCKET A

CPU

FAN

ATX

FLOPPY

IDE1

IDE2

PCI1

PCI2

PCI3

RTL

8100BL

PCI4

DDR1

AGP

SW1

F_U SB1

LINE_IN

LAN

COMB

CD_IN

PCI5

MAIN

BIOS

DDR2

DDR3

WOL

F_AUDIO

F2_1394F1_1394

CI

PDC

20276 **

IDE4**

IDE3**

IEEE 1394 ***

NB_FAN

F_PANEL

F_U SB2F3-1394

PWR

FAN

AUX_IN

SUR_CEN

IR

SPDIF_O SPDIF_IN

USB 2.0

PWR_LED

SCR

RAM_LED

SIL3112 *

S_ATA2*

S_ATA1*

K7 Triton 400

FSB333

DDR400+

AGP 8X

VT6306

***

" * " FOR GA-7VAXP-A Ultra Only.

" ** " FOR GA-7VAXP-A Ultra / GA-7VAXP-A Only.

" *** " For GA-7VAXP-A Ultra / GA-7VAXP-A / GA-7VAX1394-A Only.

- 9 - Hardware Installation Process

English

Block Diagram

" * " FOR GA-7VAXP-A Ultra Only.

" ** " FOR GA-7VAXP-A Ultra / GA-7VAXP-A Only.

" *** " For GA-7VAXP-A Ultra / GA-7VAXP-A / GA-7VAX1394-A Only.

VIA

KT400A

VIA

VT8235

CPUCLK+/- (100/133/166MHz)

System Bus

200/266/333MHz FSB

AGPCLK66 MHz

33 MHz

14.318 MHz

48 MHz

LPC BUS

AGP 4X/8X

5 PCI

PCICLK

(33MHz)

RJ45

AC97 Link

6 USB

Ports

ATA33/66/

100/133

IDE Channels

RTL8100BL

IT8705

24 MHz

33 MHz

Game Port

Floppy

LPT Port

PS/2 KB/Mouse

2 COM Ports

MIC

LINE-IN

LINE-OUT

AMD-K7

TM

Host CUP

6 Channel

CODEC

**IDE3

VIA***

VT6306

***IEEE1394

**IDE4

PDC 20276

(RAID 133)**

400/333/266MHz

DDR SDRAM

BIOS

SCR

SIL3112 *

S_ATA2*

S_ATA1*

IR

AGPCLK

66MHz

HCLK+/- (100/133/166MHz)

CLK

GEN

HCLK+/- (100/133/166MHz)

CPUCLK+/- (100/133/166MHz)

AGPCLK (66MHz)

PCICLK (33MHz)

USBCLK (48MHz)

14.318 MHz

33 MHz

PCI BUS 33MHz

66MHz V_Link

V_Link (66MHz)

- 10 -KT400A Series Motherboard

English

- 11 - Hardware Installation Process

English

Chapter 2 Hardware Installation Process

Congratulations you have accomplished the hardware installation!

Turn on the power supply or connect the power cable to the power outlet. Continue with

the BIOS/software installation.

Step 3

Step 1

Step 4

Step 5

Step 2

To set up your computer, you must complete the following steps:

Step 1- Set Dip Switch (CK_RATIO) and system Switch (SW1)

Step 2- Install the Central Processing Unit (CPU)

Step 3- Install memory modules

Step 4- Install expansion cards

Step 5- Connect ribbon cables, cabinet wires, and power supply

- 12 -KT400A Series Motherboard

English

Step 1: Install the Central Processing Unit (CPU)

Step1-1: CPU Speed Setup

The clock ratio can be switched by CK_RATIO and refer to below table.

Default Setting :

Auto (X X X X X X)

O: ON / X :OFF

Default Setting: 100MHz

5

1

ON

2 3

4

CK_RATIO

6

SW1

1

ON

SW1 CPU CLOCK

100MHz AUTO

1 ON OFF

MNote: In order to BIOS can auto detecting when

your CPU mutiplier over 18x, please adjust mutiplier

swich in CK Raito to "AUTO."

RATIO 1 2 3 4 5 6

AUTO X X X X X X

(Default)

5x O O X O O O

5.5x X O X O O O

6x O X X O O O

6.5x X X X O O O

7x O O O X O O

7.5x X O O X O O

8x O X O X O O

8.5x X X O X O O

9x O O X X O O

9.5x X O X X O O

10x O X X X O O

10.5x X X X X O O

11x O O O O O O

11.5x X O O O O O

12x O X O O O O

12.5x X X O O O O

13x O O X O X O

13.5x X O X O X O

14x O X X O X O

15x O O O X X O

16x O X O X X O

16.5x X X O X X O

17x O O X X X O

18x X O X X X O

O: ON / X :OFF

CLK_RATIO

You must set SW1 to 100MHz when

you used FSB 200MHz CPU.

100MHz : Fix FSB 200MHz CPU

Auto : Support FSB 266/333 MHz CPU

- 13 - Hardware Installation Process

English

Step1-2: CPU Installation

CPU Top View CPU Bottom View

Socket Actuation Lever

1. Pull up the CPU socket lever

and up to 90-degree angle.

Pin1 indicator

2. Locate Pin 1 in the socket and look

for a (golden) cut edge on the CPU

upper corner. Then insert the CPU

into the socket.

Before installing the processor, adhere to the following warning:

1.Please make sure the CPU type is supported by the motherboard.

2.If you do not match the CPU socket Pin 1 and CPU cut edge well, it will

cause improper installation. Please change the insert orientation.

- 14 -KT400A Series Motherboard

English

Step1-3:CPU Cooling Fan Installation

3. Fasten the cooling fan supporting-base

onto the CPU socket on the main-

board.

2. Use qualified fan approved by AMD.

4. Make sure the CPU fan is

plugged to the CPU fan connector,

than install complete.

1. Press down the CPU socket

lever and finish CPU installation.

1. Please use AMD approved cooling fan.

2. We recommend you to apply the thermal paste to provide better heat

conduction between your CPU and Cooling Fan.

3.Make sure the CPU fan power cable is plugged in to the CPU fan connector, this

completes the installation.

Please refer to CPU cooling fan user's manual for more detail installation procedure.

Before installing the CPU Heat Sink , adhere to the following warning:

- 15 - Hardware Installation Process

English

Step 2: Install memory modules

DDR

Notch

Before installing the memory modules, adhere to the following warning:

1. When DIMM LED is ON, do not install / remove DIMM from socket.

2. Please note that the DIMM module can only fit in one direction due to the one

notch. Wrong orientation will cause improper installation. Please change the

insert orientation.

The motherboard has 3 dual inline memory module(DIMM) sockets. The BIOS will automati-

cally detects memory type and size. To install the memory module, just push it vertically into the

DIMM Slot. The DIMM module can only fit in one direction due to the notch. Memory size can vary

between sockets.

Support Unbuffered DDR DIMM Sizes type:

64 Mbit (2Mx8x4 banks) 64 Mbit (1Mx16x4 banks) 128 Mbit(4Mx8x4 banks)

128 Mbit(2Mx16x4 banks) 256 Mbit(8Mx8x4 banks) 256 Mbit(4Mx16x4 banks)

512 Mbit(16Mx8x4 banks) 512 Mbit(8Mx16x4 banks)

Total System Memory (Max3GB)

- 16 -KT400A Series Motherboard

English

DDR Introduction

Established on the existing SDRAM industry infrastructure, DDR (Double Data Rate) memory is a high

performance and cost-effective solution that allows easy adoption for m emory vendors, OEMs and system

integrators.

DDR memory is a sensible evolutionary solution for the PC industry that builds on the existing SDRAM

infrastructure, yet makes awesome advances in solving the system performance bottleneck by doubling the

memory bandwidth. DDR SDRAM will offer a superior solution and m igration path from existing SDRAM

designs due to its availability, pricing and overall market support. PC2100 DDR memory (DDR266) doubles

the data rate through reading and writing at both the rising and falling edge of the clock, achieving data

bandwidth 2X greater than PC133 when running with the same DRAM clock frequency. With peak band-

width of 2.664GB per second, DDR memory enables system OEM s to build high perform ance and low

latency DRAM subsystems that are suitable for servers, workstations, high-end PC's and value desktop SMA

systems. With a core voltage of only 2.5 volts compared to conventional SDRAM's 3.3 volts, DDR memory is

a compelling solution for small form factor desktops and notebook applications.

1. The DIMM slot has a notch, so the DIMM

memory module can only fit in one direction.

2. Insert the DIMM memory module vertically into

the DIMM slot. Then push it down.

3. Close the plastic clip at both edges of the DIMM

slots to lock the DIMM module.

Reverse the installation steps when you wish

to remove the DIMM module.

Page is loading ...

Gigabyte GA-7VAXP-A User manual

This manual is also suitable for

Gigabyte GA-7VAXP-A User manual

Related papers

Other documents