Gigabyte Titan III User manual

USER’S MANUAL

GA-8ITX Series

P4 Titan-RDRAM Motherboard

Pentium

®

4 Processor Motherboard

Rev. 1.1 Second Edition

12ME-8ITX-1102

When you installing AGP card, please make sure the

following notice is fully understood and practiced. If your

AGP card has "AGP 4X notch"(show below), please make

sure your AGP card is AGP 4X (1.5V).

Do not use AGP 2X card (3.3V) in this motherboard. It will

burn and damage the motherboard due to Intel

®

850 chipset

can't support AGP 2X(3.3V).

Example 1: Diamond Vipper V770 golden finger is compatible

with 2X/4X mode AGP slot. It can be switched between AGP 2X

(3.3V) or 4X(1.5V) mode by adjusting the jumper. The factory

default for this card is 2X(3.3V). If you install this card in GA-8ITX

series (or any AGP 4X only) motherboards without switching the

jumper to 4X mode (1.5V), it will burn the motherboard.

Example 2: ATi Rage 128 Pro (Power Color) & SiS 305 golden

finger is compatible with 2X/4X mode AGP slot, but it supports

2X(3.3V) only. If you install this card in GA-8ITX series (or any

AGP 4X only) motherboards, it will burn the motherboard.

 The author assumes no responsibility for any errors

or omissions that may appear in this document nor

does the author make a commitment to up

date the information contained herein.

 Third-party brands and names are the property of

their respective owners.

 Please do not remove any labels on motherboard, this

may void the warranty of this motherboard.

 Due to rapid change in technology, some of the

specifications might be out of date before pwblicution

of this booklet.

FCC Part 15, Subpart B, Section 15.107(a) and Section 15.109(a),

Class B Digital Device

DECLARATION OF CONFORMITY

Per FCC Part 2 Section 2.1077(a)

Responsible Party Name:

Address:

Phone/Fax No:

hereby declares that the product

Product Name:

Conforms to the following specifications:

This device complies with part 15 of the FCC Rules. Operation is

subject to the following two conditions: (1) This device may not

cause harmful and (2) this device must accept any inference received,

including that may cause undesired operation.

Representative Person’s Name:

Signature:

Eric Lu

Supplementary Information:

Model Number:

18305 Valley Blvd., Suite#A LA

Puent, CA 91744

G.B.T. INC.

(818) 854-9338/ (818) 854-9339

Motherboard

GA-8ITX/GA-8ITXR

Date:

ERIC LU

August 20,2001

Declaration of Conformity

We, Manufacturer/Importer

(full address)

G.B.T. Technology Träding GMbH

Ausschlager Weg 41, 1F, 20537 Hamburg, Germany

declare that the product

( description of the apparatus, system, installation to which it refers)

Mother Board

GA-8ITX/GA-8ITXR

is in conformity with

(reference to the specification under which conformity is declared)

in accordance with 89/336 EEC-EMC Directive

 EN 55011 Limits and methods of measurement

of radio disturbance characteristics of

industrial,scientific and medical (ISM

high frequency equipment

 EN 61000-3-2*

 EN 60555-2

Disturbances in supply systems cause

by household appliances and similar

electrical equipment “Harmonics”

 EN 55013

Limits and methods of measurement

of radio disturbance characteristics of

broadcast receivers and associated

equipment

 EN 61000-3-3* Disturbances in supply systems cause

by household appliances and similar

electrical equipment “Voltage fluctuations”

 EN 55014 Limits and methods of measurement

of radio disturbance characteristics of

household electrical appliances,

portable tools and similar electrical

apparatus

 EN 50081-1

Generic emission standard Part 1:

Residual commercial and light industry

 EN 50082-1

Generic immunity standard Part 1:

Residual commercial and light industry

 EN 55015 Limits and methods of measurement

of radio disturbance characteristics of

fluorescent lamps and luminaries

Generic emission standard Part 2:

Industrial environment

 EN 55081-2

Immunity from radio interference of

broadcast receivers and associated

equipment

Generic emission standard Part 2:

Industrial environment

 EN 55082-2

 EN 55022 Limits and methods of measurement

of radio disturbance characteristics of

information technology equipment

lmmunity requirements for household

appliances tools and similar apparatus

 ENV 55104

Cabled distribution systems; Equipment

for receiving and/or distribution from

sound and television signals

EMC requirements for uninterruptible

power systems (UPS)

 EN50091-2

 EN 55020

 DIN VDE 0855

 part 10

 part 12

(EC conformity marking)

 CE marking

The manufacturer also declares the conformity of above mentioned product

with the actual required safety standards in accordance with LVD 73/23 EEC

Safety requirements for mains operated

electronic and related apparatus for

household and similar general use

 EN 60950

 EN 60065

Safety of household and similar

electrical appliances

 EN 60335

Manufacturer/Importer

Signature:

Name:

(Stamp)

Date : August 20, 2001

 EN 60555-3

Rex Lin

 EN 50091-1

2

GA-8ITX Series Motherboard

Table Of Content

Revision History.....................................................................................4

Item Checklist .........................................................................................4

WARNING!...............................................................................................5

Chapter 1 Introduction.............................................................................6

Summary of Features .................................................................................. 6

GA-8ITX Series Motherboard Layout......................................................... 8

Chapter 2 Hardware Installation Process................................................9

Step 1: Install the Central Processing Unit (CPU).....................................10

CPU Installation ............................................................................................................... 10

CPU Heat Sink Installation...............................................................................................11

Step 2: Install memory modules................................................................12

Introduce RIMM (Rambus In-line Memory Module) .................................................... 13

Step 3: Install expansion cards .................................................................14

Step 4: Connect ribbon cables, cabinet wires, and power supply ...........15

I/O Back Panel Introduction ............................................................................................ 15

Connectors Introduction .................................................................................................. 17

Jumper Setting ................................................................................................................. 24

ATX 12V Power Supply Introduction ............................................................................. 26

6 Pin Aux. Power Connector......................................................................................... 26

Chapter 3 BIOS Setup ..........................................................................27

Select Language .......................................................................................29

The Main Menu (For example: BIOS Ver. :F4).........................................29

Standard CMOS Features.........................................................................31

3

Table of Content

BIOS Features Setup.................................................................................34

Chipset Features Setup.............................................................................36

Power Management Setup .......................................................................39

PNP/PCI Configuration..............................................................................43

Load Fail-Safe Defaults.............................................................................45

Load Optimized Defaults...........................................................................46

Integrated Peripherals ...............................................................................47

Hardware Monitor & MISC Setup..............................................................53

Set Supervisor / User Password ................................................................55

IDE HDD Auto Detection............................................................................56

Save & Exit Setup.......................................................................................57

Exit Without Saving ....................................................................................58

Chapter 4 Technical Reference ............................................................59

Performance List .......................................................................................59

Block Diagram...........................................................................................60

Dual BIOS Introduction (For GA-8ITXR Only) ..........................................61

Four Speaker & SPDIF Introduction(For GA-8ITXR Only).......................69

@ BIOS Introduction..................................................................................73

Easy TuneIII

TM

Introduction .......................................................................74

RAID Introduction(For GA-8ITXR Only) ....................................................75

Chapter 5 Appendix..............................................................................98

4

GA-8ITX Series Motherboard

Revision Revision Note Date

1.0 Initial release of the GA-8ITX Series motherboard user's manual. Aug.2001

1.1 Initial release of the GA-8ITX Series motherboard user's manual. Sep.2001

1.1 Second release of the GA-8ITX Series motherboard user's manual. Sep.2001

 The GA-8ITX Series motherboard

 IDE cable x 1 or x 3*

 Floppy cable x 1

 USB cable x 1

 CD for motherboard driver & utility (IUCD)

 GA-8ITX Series user’s manual

 I/O Shield

 Quick PC Installation Guide

 CRIMM x 2

Revision History

Item Checklist

"*" For GA-8ITXR only.

5

WARNING!

Computer motherboards and expansion cards contain very delicate Integrated Circuit (IC) chips. To

protect them against damage from static electricity, you should follow some precautions whenever you

work on your computer.

1. Unplug your computer when working on the inside.

2. Use a grounded wrist strap before handling computer components. If you do not have

one, touch both of your hands to a safely grounded object or to a metal object, such as

the power supply case.

3. Hold components by the edges and try not touch the IC chips, leads or connectors, or

other components.

4. Place components on a grounded antistatic pad or on the bag that came with the

components whenever the components are separated from the system.

5. Ensure that the ATX power supply is switched off before you plug in or remove the ATX

power connector on the motherboard.

If the motherboard has mounting holes, but they don’t line up with the holes on the base and there are

no slots to attach the spacers, do not become alarmed you can still attach the spacers to the mounting

holes. Just cut the bottom portion of the spacers (the spacer may be a little hard to cut off, so be careful

of your hands). In this way you can still attach the motherboard to the base without worrying about short

circuits. Sometimes you may need to use the plastic springs to isolate the screw from the motherboard

PCB surface, because the circuit wire may be near by the hole. Be careful, don’t let the screw contact

any printed circuit write or parts on the PCB that are near the fixing hole, otherwise it may damage the

board or cause board malfunctioning.

Installing the motherboard to the chassis…

WARNING!

6

GA-8ITX Series Motherboard

Form Factor  30.5cm x 24.5cm ATX size form factor, 6 layers PCB.

Motherboard  GA-8ITX Series Motherboard:

GA-8ITX and GA-8ITXR

CPU  Socket 478 for Intel

®

Micro FC-PGA2 Pentium

®

4 processor

 Intel Pentium

®

4 400MHz FSB

 2nd Level cache depend on CPU

Chipset  Chipset 82850 HOST/AGP/Controller

 82801BA(ICH2) I/O Controller Hub

Memory  4 184-pin RIMM Sockets

 Dual direct RDRAM channel

 Supports up to 2GB (Max)

I/O Control  Winbond W83627HF

Slots  1 CNR(Communication and Networking Riser) Slot

 1 AGP support 4X(1.5V) device

 6 PCI slot supports 33MHz & PCI 2.2 compliant

On-Board IDE  An IDE controller on the Intel 82801BA PCI chipset

provides IDE HDD/CD-ROM with PIO, Bus Master (Ultra

DMA33/ATA66/ATA100) operation modes.

 Can connect up to four IDE devices

On-Board Peripherals  1 Floppy port supports 2 FDD with 360K, 720K,1.2M, 1.44M

and 2.88M bytes.

 1 Parallel port supports Normal/EPP/ECP mode

 2 Serial ports (COMA&COMB)

 4 USB ports (Rear USB x 2, Front USB x 2)

 1 IrDA connector for IR/CIR

Hardware Monitor  CPU/Power/System Fan Revolution detect

 CPU Overheat Warning

 System Voltage Detect

Summary of Features

Chapter 1 Introduction

to be continued......

7

Introduction

On-Board LAN  Build in RTL8100(B)L Chipset *

On-Board Sound  Creative CT5880 Sound Chipset *

 2/4* channel audio CODEC

 Line In/Line Out/Mic In/CD In/Game Port/AUX IN*/TEL*

On-Board RAID*  Support data striping (RAID 0) or mirroring (RAID 1)

 Supports concurrent dual IDE controller operation

 Supports IDE bus master operation

 Displays status and error checking messages during boot-up

 Mirroring supports automatic background rebuilds

 Features LBA and Extended Interrupt13 drive translation in

controller onboard BIOS

PS/2 Connector  PS/2 Keyboard interface and PS/2 Mouse interface

BIOS  Licensed AMI BIOS, 4M bit FWH

 Supports Dual BIOS *

Additional Features  PS/2 Keyboard power on by password

 PS/2 Mouse power on

 External Modem wake up

 STR(Suspend-To-RAM)

 Wake on LAN

 AC Recovery

 USB KB/Mouse wake up from S3

 Supports @BIOS

 Supports EasyTuneIII

 Supports Multi Language

Special Features  Over Voltage (RIMM/AGP/CPU)*

 Over Clock (CPU/PCI/AGP)*

"*" For GA-8ITXR only."**" For GA-8ITX only .

 Please set the CPU host frequency in accordance with your processor’s specifications.

We don’t recommend you to set the system bus frequency over the CPU’s specification

because these specific bus frequencies are not the standard specifications for CPU,

chipset and most of the peripherals. Whether your system can run under these specific

bus frequencies properly will depend on your hardware configurations, including CPU,

Chipsets,SDRAM,Cards….etc.

8

GA-8ITX Series Motherboard

GA-8ITX Series Motherboard Layout

KB/MOUSE

COMACOMB

LPT

SOCKET478

PWR_FAN

MIC_IN LINE_OUT

LINE_IN

GAME

USB

LAN*

J16

USB_VS

CPU_FAN

TEHAMA

W83627

AGP1

PCI1

PCI2

PCI3

PCI4

J2

JP23

CODEC

RTL8100*

CT5880*

PCI5

PCI6

CN2

CN10

PDC20265*

JP32*

IDE3*

IDE4*

BACKUP

BIOS*

MAIN

BIOS

J17

JP12*

J7

BAT1

ICH2

JP15

RIMM1

RIMM2

RIMM3

RIMM4

IDE2

IDE1

FLOPPY

J18

J15

LED2

GA-8ITX(R)

P4 Titan

RDRAM

SYS_FAN

"*" For GA-8ITXR only.

J3*

J4*

9

Hardware Installation Process

To set up your computer, you must complete the following setups:

Step 1- Install the Central Processing Unit (CPU)

Step 2- Install memory modules

Step 3- Install expansion cards

Step 4- Connect ribbon cables, cabinet wires, and power supply

Step 5- Setup BIOS software

Step 6- Install supporting software tools

Chapter 2 Hardware Installation Process

Step 1

Step 2

Step 4

Step 3

10

GA-8ITX Series Motherboard

Step 1: Install the Central Processing Unit (CPU)

CPU Installation

 Please make sure the CPU type is supported by the motherboard.

Pin1 indicator

Pin1indicator

CPU Top View CPU Bottom View

Socket Actuation Lever

1. Pull up the CPU socket level

and up to 90-degree angle.

Pin1 indicator

2. Locate Pin 1 in the socket and look

for a (golden) cut edge on the CPU

upper corner. Then insert the CPU

into the socket.

3. Press down the CPU socket lever and

finish CPU installation.

11

Hardware Installation Process

CPU Heat Sink Installation

1. Fasten the heatsink supporting-base

onto the CPU socket on the main-

board.

2. Make sure the CPU fan is plugged

to the CPU fan connector, than

install complete.

 Please use Intel approved cooling fan.

 We recommend you to apply the thermal tape to provide better heat

conduction between your CPU and heatsink.

(The CPU cooling fan might stick to the CPU due to the hardening of the

thermal paste. During this condition if you try to remove the cooling fan, you

might pull the processor out of the CPU socket alone with the cooling fan, and

might damage the processor. To avoid this from happening, we suggest you to

either use thermal tape instead of thermal paste, or remove the cooling fan with

extreme caution.)

 Make sure the CPU fan power cable is plugged in to the CPU fan connector,

this completes the installation.

 Please refer to CPU heat sink user’s manual for more detail installation

procedure.

12

GA-8ITX Series Motherboard

Step 2: Install memory modules

The motherboard has 4 Rambus In-line Memory Module (RIMM) sockets. The BIOS will automati-

cally detect memory type and size. To install the memory module, just push it vertically into the

RIMM Slot .The RIMM module can only fit in one direction due to the two notches. Please note; Both

RIMM modules inserted on RIMM1 and RIMM2 slots are recommended to have the same size,

frequency. If not, the larger sized module will l be automatically re-sized by BIOS to match the

smaller sized module. The same rule applies to both RIMM3 and RIMM4 slots.

You can insert two RIMMs or four RIMMs into RIMM slots, but C-RIMM (Continuity RIMM)

modules must be inserted into the empty slots.

Push the ejector tab towards the RIMM.

 When STR/RIMM LED is ON, you do not install / remove RDRAM from socket.

RIMM

CRIMM

Check RIMM module if it is supported by the

M/B.

Insert the RIMM module into the slot.

13

Hardware Installation Process

Introduce RIMM (Rambus In-line Memory Module)

Direct Rambus Memory Controller

Directly support a Dual Direct Rambus * Channel

 Supports 300&400 MHz Direct Rambus * Channel @ 100MHz host bus frequency.

 Maximum memory array size up to 256MB using 64Mb/72Mb, 512MB using 128Mb/144Mb,

1GB using 256Mb/288Mb DRAM technology

Supports up to 32 Direct Rambus devices per channel

Supports a maximum DRAM address decode space of 4GB

Configurable optional ECC operation

 ECC with single bit Error Correction and multiple bit Error Detection

 Single bit errors corrected and written back to memory (auto-scrubbing)

 Parity mode not supported

APIC memory space in hardware. It is the BIOS or system designer's responsibility to limit DRAM

population so that adequate PCI, AGP, High BIOS, and APIC memory space can be allocated.

14

GA-8ITX Series Motherboard

Step 3: Install expansion cards

1. Read the related expansion card’s instruction document before install the expansion card into

the computer.

2. Remove your computer’s chassis cover, necessary screws and slot bracket from the computer.

3. Press the expansion card firmly into expansion slot in motherboard.

4. Be sure the metal contacts on the card are indeed seated in the slot.

5. Replace the screw to secure the slot bracket of the expansion card.

6. Replace your computer’s chassis cover.

7. Power on the computer, if necessary, setup BIOS utility of expansion card from BIOS.

8. Install related driver from the operating system.

 When you try to install VGA Card, please note that the motherboard only

support AGP 4X(1.5V) VGA Card.

15

Hardware Installation Process

Step 4: Connect ribbon cables, cabinet wires, and power

supply

I/O Back Panel Introduction

 PS/2 Keyboard and PS/2 Mouse Connector

 Parallel Port and Serial Ports (COMA/COMB)

PS/2 Mouse Connector

(6 pin Female)

PS/2 Keyboard Connector

(6 pin Female)

Parallel Port

(25 pin Female)

COMA COMB

Serial Ports (9 pin Male)

This connector supports standard PS/2

keyboard and PS/2 mouse.

This connector supports 2 standard COM ports

and 1 Parallel port. Device like printer can be

connected to Parallel port ; mouse and modem

etc can be connected to Serial ports.









16

GA-8ITX Series Motherboard

 Game /MIDI Ports

Joystick/ MIDI (15 pin Female)

 USB/LAN Connector

 Audio Connectors

This connector supports joystick, MIDI keyboard and other

relate audio devices.

 After install onboard audio driver, you may connect

speaker to Line Out jack, micro phone to MIC In jack.

Device like CD-ROM , walkman etc can be connected

to Line-In jack.

Before you connect your device(s) into USB connector(s),

please make sure your device(s) such as USB keyboard,

mouse, scanner, zip,speaker..etc. Have a standard USB

interface. Also make sure your OS (Win 95 with USB

supplement, Win98, Windows 2000, Windows ME, Win

NT with SP 6) supports USB controller. If your OS does not

support USB controller, please contact OS vendor for pos-

sible patch or driver upgrade. For more information please

contact your OS or device(s) vendors.

Line In

MIC In

Line Out

USB 0

USB 1

LAN*

Connector

"*" For GA-8ITXR only.

Page is loading ...

Gigabyte Titan III User manual

This manual is also suitable for

Gigabyte Titan III User manual

Related papers

Other documents