Cooper 1050E-T Installation guide

Cooper
Brand
Cooper
Model
1050E-T
Category
Network switches
Type
Installation guide

Cooper 1050E-T is an Ethernet switch designed for use in industrial environments. It supports 10/100TX Ethernet ports and has a DC power input range of 12VDC ~ 48VDC. The 1050E-T also has a surge EARTH terminal block for power 1, power 2, and fault alarm contact. This device is suitable for use in Class I, Division 2, Groups A, B, C, and D or non-hazardous locations only. With its rugged design and industrial certifications, the 1050E-T is an ideal choice for connecting Ethernet devices in harsh environments.

Cooper 1050E-T is an Ethernet switch designed for use in industrial environments. It supports 10/100TX Ethernet ports and has a DC power input range of 12VDC ~ 48VDC. The 1050E-T also has a surge EARTH terminal block for power 1, power 2, and fault alarm contact. This device is suitable for use in Class I, Division 2, Groups A, B, C, and D or non-hazardous locations only. With its rugged design and industrial certifications, the 1050E-T is an ideal choice for connecting Ethernet devices in harsh environments.

1050E-T ETHERNET SWITCH INSTALLATION GUIDE
©2013 Cooper Bussmann
www.cooperbussmann.com/wirelessresources
10/16 Page 1 of 2 Version 1.0
Power Input and Fault Alarm Contact Wire Gauge: 12 ~ 24 AWG.
RJ-45 Port Connection: Use four twisted pair Cat 5 or Cat 5e cables less than 100 meters long.
NOTE This equipment is suitable for use in Class I, Division 2, Groups A, B, C, and D or
non-hazardous locations only.
WARNING – EXPLOSION HAZARD!
• Donotdisconnectequipmentwhilethecircuitisliveunlesstheareaisknowntobefree
ofignitableconcentrations.
• Donotdisconnectequipmentunlesspowerhasbeenremovedortheareaisknowtobe
non-hazardous.
• SubstitutionofanycomponentsmayimpairsuitabilityforClassI,Division2.
• Theareamustbeknowntobenon-hazardousbeforeservicingorreplacingtheunitand
beforeinstallingtheunit.
WARNING Exposure to some chemicals may degrade the sealing properties of materials used
in the sealed relay device. It is recommended to inspect the sealed relay device periodically
and to check for any degradation of the materials and to replace the complete product (not
the sealed device) if any degradation is found.
Surge EARTH
Terminal Block for Power 1,
Power 2 and Fault Alarm Contact
1. Insert DC power wires into the contacts for Power Supply 1 and 2.
2. Tighten the terminal screws to ensure that the wires do not come loose.
Power Supply 2*
Power Supply 1
*Power Supply 2 is used for
redundant supplies.
POWER SUPPLY WIRING
DC Power Input Range:
12VDC ~ 48VDC
1050E-T
DC
DC
10/100 TX RJ-45 Ethernet Ports
Surge EARTH
FAULT ALARM
CONTACT
1A@24V
N/C Contact.
Contact will open
when a fault occurs
DIN-RAIL MOUNTING
1. Insert the top of the DIN rail clip
onto the DIN rail.
2. Press the 1050E-T onto the DIN rail
until it clicks into place.
3. Check the module is securely attached to the DIN rail.
4. To remove the 1050E-T from the DIN rail, press down on the rear top
of the module and swing the bottom of the module forward.
1050E-T ETHERNET SWITCH INSTALLATION GUIDE
10/16 Page 2 of 2 Version 1.0
©2013 Cooper Bussmann
www.cooperbussmann.com/wirelessresources
WALL MOUNT PLATE MOUNTING
1. Remove the DIN rail from the 1050E-T by loosening the three screws.
2. Place the wall mount plates on the top and bottom panels of the 1050E-T.
4. Use the hook holes at the corners of the wall mount plates to mount the 1050E-T on
the wall.
5. To remove the 1050E-T from the wall, reverse the above steps.
3. Use the screws to screw the wall
mount plates onto the 1050E-T.
  • Page 1 1
  • Page 2 2

Cooper 1050E-T Installation guide

Cooper
Brand
Cooper
Model
1050E-T
Category
Network switches
Type
Installation guide

Cooper 1050E-T is an Ethernet switch designed for use in industrial environments. It supports 10/100TX Ethernet ports and has a DC power input range of 12VDC ~ 48VDC. The 1050E-T also has a surge EARTH terminal block for power 1, power 2, and fault alarm contact. This device is suitable for use in Class I, Division 2, Groups A, B, C, and D or non-hazardous locations only. With its rugged design and industrial certifications, the 1050E-T is an ideal choice for connecting Ethernet devices in harsh environments.

Download PDF
report

Ask a question and I''ll find the answer in the document

Finding information in a document is now easier with AI

Related papers

Other documents