Agri-Fab 45-0309-062 User manual

Agri-Fab
Brand
Agri-Fab
Model
45-0309-062
Category
Spreader
Type
User manual
• Safety
• Assembly
• Operation
• Maintenance
• Parts
CAUTION:
ReadRulesfor
SafeOperation
andInstructions
Carefully
PRECAUCION:
Leacuidadosamentelos
Porcedimientose
Instruccionesparala
OperaciónSeguradela
Máquina.
PRINTEDINU.S.A.
32" POLY
SPIKER/SPREADER
OWNERS MANUAL
MANUAL DEL USUARIO
Model No.
Modelo No.
45-0309-062
FORMNO.42172rev.(6/22/11)
SURCADOR-ESPARCIDOR DE 32”
• Seguridad
• Montaje
• Operación
• Mantenimiento
• PiezasdeRepuesto
Call1-800-448-9282formissingpartsorassemblyhelp.
2
RULES FOR SAFE OPERATIONS
• Readthisowner'smanualbeforeattemptingtoassemble
oroperatethespiker/spreader.
• Readthetowingvehicleowner'smanualandknowhow
tooperatethetractorbeforeusingthespiker/spreader
attachment.
• Do not allow anyone to ride on or sit on the spiker/
spreader.
• Never allow children to operate the tractor or spiker/
spreaderattachment.
• Do not allow adults to operate the tractor or spiker/
spreaderwithoutproperinstructions.
• Readthechemicallabelforinstructionsand
cautionsforhandlingandapplyingchemicals.
Anypowerequipmentcancauseinjuryifoperatedimproperlyoriftheuserdoesnotunderstandhowtooperatetheequipment.
Exercisecautionatalltimes,whenusingpowerequipment.
• Weareyeandhandprotectionwhenhandlingandusing
lawnchemicals.
• Alwaysbeginwiththetransmissioninrst(low)gearand
graduallyincreasespeedasconditionspermit.Maximum
towingspeed-10M.P.H.
• Donotdrivetooclosetoacreekorditchandbealert
forholesandotherhazardswhichcouldcauseyouto
loosecontrolofthetractorandspiker/spreader.
• Beforeoperatingthevehicleonanygrade(hill)referto
thesafetyrulesinthevehicleowner'smanualconcerning
safeoperationonslopes.Stay off steep slopes!
• Follow maintenance and lubrication instructions as
outlinedinthismanual.
Lookforthissymboltopointoutimportantsafetyprecautions.Itmeans–Attention!!
Become alert!! Yoursafetyisinvolved.
CARTON CONTENTS
1. ChainCover
2. FlowControlLever
3. CenterBrace
4. HopperAssembly
5. HitchTube(2)
6. LiftHandle
7. SpikeDisk(7)
8. DriveDiskAssembly(2)
9. Wheel(2)
10.TransportTubeAssembly
11.HitchBracket(2)
12.SpikerShaftAssembly
1
2
3
8
12
10
9
4
6
7
5
11
3
HARDWARE CHART
A
B
C D E F
L
M
N
G
H I
J
SHOWN FULL SIZE
P
Q
R
NOT SHOWN FULL SIZE
O
U
V
T
X
Y
GG
EE
HH
CC
DD
FF
BB
AA
Z
II
JJ
S
W
K
REF. PART NO. QTY DESCRIPTION
REF. PART NO. QTY DESCRIPTION
A 45100 2 HexBolt,1/2"x4"FullThread
B 43224 3 HexBolt,5/16"x2-1/4"
C 44180 2 HexBolt,5/16"x2"
D 43084 2 HexBolt,5/16"x1-3/4"
E 43085 2 HexBolt,5/16"x1-1/2"
F 43063 1 HexBolt,5/16"x1"
G 1509-90 1 HexBolt,1/4-20x1-1/4"
H 43012 1 HexBolt,1/4-20x3/4"
I 44215 1 CarriageBolt,5/16"x1-3/4"
J 44731 2 SelfTappingScrew,1/4"x1/2"
K 43178 1 HexNut,1/4"
L 47189 5 NylockHexNut,1/4"
M 47810 10 NylockHexNut,5/16"
N 43019 2 JamNut,1/2"
O 48115 2 NylockJamNut,1/2"
P 43088 2 FlatWasher,1/4"
Q 1543-69 2 NylonWasher,21/64"
R 43081 4 FlatWasher,5/16"
S R19171616 4 FlatWasher,1/2"
T R19212016 10 FlatWasher,5/8"
U 43093 3 CotterPin,1/8"x1-1/2"
V 44101 1 CotterPin,3/32"x3/4"
W 43343 1 HairCotterPin,1/8"
X 47960 1 ChainwithConnectingLink
Y 741-0249 13 FlangedBearing
Z 47777 1 CompressionSpring
AA 23520 1 1/4"ThickSpacer
BB 46497 2 ShortSpacerTube
CC 46524 5 LongSpacerTube
DD 47959 1 FlowControlLink
EE 47969 1 Ferrule
FF 43848 1 ControlLeverGrip
GG 43943 1 HeightAdjustmentGrip
HH 712-0421 1 PlasticWingNut
II 47623 1 FlatHeadHitch,Pin,3/8"
JJ 47962 1 FlowPlateSpring
4
TOOLS REQUIRED FOR ASSEMBLY
(2)7/16"Wrenches
(2)1/2"Wrenches
(2)3/4"orAdjustableWrenches
(1)Screwdriver
(1)Pliers
ASSEMBLY
FIGURE 2
4. Assemblethegripontothelifthandle.Seegure2.
5. Ontherightside,inserta5/16"x1-3/4"hexboltthrough
a5/16"atwasherandthenthroughtherearholeinthe
hopperandthehitchtube.Assemblethetransporttube
andthenthelifthandleontotheboltandsecurewitha
5/16"nylockhexnut.Do not tighten yet. Seegure2.
6. Assemblea5/16"x1"hexboltand5/16"nylockhexnut
tothebottomholeinthetransporttubeassemblyand
thelifthandle.Tighten.Seegure2.
FIGURE 3
1. Removethehardwarepackandallindividualpartsfrom
thecarton.Layoutasshownonpages2and3.
2. Attachahitchtubetothefrontholeintherighthandside
ofthehopperusinga5/16"x1-1/2"hexbolt,a5/16"at
washeranda5/16"nylockhexnut.Assemblethebolt
andwasherfrominsidethehopper.Do not tighten yet.
Seegure1.
3. Repeatonthelefthandsideofthehopper.
FIGURE 1
Spikepointsaresharp.Exercisecautionwhen
handlingandworkingnearspikedisks.
HITCH TUBE
(R) 5/16" FLAT
WASHER
(E) 5/16" 1-1/2"
HEX BOLT
(M) 5/16" NYLOCK HEX NUT
7. Ontheleftside,inserta5/16"x1-3/4"hexboltthrough
a5/16"atwasherandthenthroughtherearholeinthe
hopperandthehitchtube.Assemblethetransporttube
ontotheboltandsecureitwitha5/16"nylockhexnut.
Do not tighten yet. Seegure3.
ENGLISH
VIEWED FROM FRONT RIGHT CORNER
VIEWED FROM FRONT LEFT CORNER
(M) 5/16" NYLOCK
HEX NUT
(R) 5/16" FLAT
WASHER
(D) 5/16" x 1-3/4"
HEX BOLT
LIFT
HANDLE
TRANSPORT TUBE
(M) 5/16" NYLOCK
HEX NUT
(F) 5/16" x 1"
HEX BOLT
(GG) GRIP
(R) 5/16"
FLAT WASHER
(D) 5/16" x 1-3/4"
HEX BOLT
5
FIGURE 7
FIGURE 4
8. Fasten the hitch tubes together using three 5/16" x
2-1/4" hex bolts and 5/16" nylock hex nuts. Do not
tighten yet.Seegure4.
FIGURE 5
(M) 5/16" NYLOCK
HEX NUT (2)
(W) HAIR COTTER
PIN (1/8")
(II) HITCH PIN
(C) 5/16" x 2"
HEX BOLT (2)
12.Assemblea1/2"atwasher,awheel,another1/2"at
washerandthena1/2"jamnutontoa1/2"x4"hexbolt.
Tightenthenutngertightandthenbackoff1/4to1/2
turn.Seegure6.
13.Assembletheboltandwheeltothetransporttubeusing
a1/2"nylockjamnut.Tightenthenutbutdon'tcollapse
thetube.Seegure6.
FIGURE 6
TRANSPORT
TUBE
(O) 1/2" NYLOCK
JAM NUT
(S) 1/2" FLAT
WASHER
(A) 1/2" x 4"
HEX BOLT
(N) 1/2" HEX
JAM NUT
16.Screwa1/4"hexnutallthewayontotheowcontrol
link.Assembletheferruleontothelinkandthenstarta
1/4"nylockhexnutoneortwoturnsontothelink.See
gure7.
17.Assembletheferruleintotheholeattheendoftheow
controlleverusinga1/4"nylockhexnut.Tightenthe
nut,leavingitlooseenoughthattheferrulecanpivot.
Seegure7.
18.Assemblethegripontotheendoftheowcontrollever.
Seegure7.
FLOW
CONTROL
LEVER
(L) 1/4" NYLOCK
HEX NUT
(L) 1/4" NYLOCK
HEX NUT
(K) 1/4" HEX NUT
(EE) FERRULE
(DD) FLOW
CONTROL
LINK
(FF) GRIP
ENGLISH
14.Ifthewheeldoesnotspinfreely,backoffthenylockjam
nutandthentheplainjamnut1/4to1/2turneach.
15.Assembleawheeltotheotherside.Seegure6.
9. Assemblethehitchbracketstothehitchtubesusingtwo
5/16"x2"hexboltsand5/16"nylockhexnuts.Do not
tighten.Seegure5.
10.Assemblethehitchpinthroughthehitchbracketsand
securewiththehaircotterpin.Seegure5.
IMPORTANT: Do not collapse the at ends of the hitch
tubeswhentighteningtheboltsinthenextstep.
11.Tighten, but do not overtightenthetwo5/16"x1-1/2"
hexboltsassembledinsteps2and3.
Tighten, but do not overtightenthetwo5/16"x1-3/4"
hexboltsassembledinsteps5and7.Thelifthandle
mustbeabletopivot.
Tightenthehexboltsassembledinsteps8and9.
(M) 5/16" NYLOCK
HEX NUT (3)
(B) 5/16" x 2-1/4"
HEX BOLT (3)
6
FIGURE 10
FIGURE 9
FIGURE 8
22.Insertthe5/16"x1-3/4"carriageboltupthroughtheslot
andsecureitwithanylonwasherandtheplasticwing
nut.Seegure9.
23.Movethelifthandleintothelockedpositionasshown
ingure9andthentipthespreaderbacktorestonthe
wheelsandtherearofthehopper.
CENTER
BRACE
(G) 1/4" x 1-1/4"
HEX BOLT
(L) 1/4" NYLOCK
HEX NUT
(P) 1/4" FLAT
WASHER
(P) 1/4" FLAT
WASHER
(H) 1/4" x 3/4"
HEX BOLT
(L) 1/4" NYLOCK
HEX NUT
(HH) PLASTIC WING NUT
(Q) NYLON
WASHER
(I) 5/16" x 1-3/4"
CARRIAGE BOLT
LOCKED POSITION
19.Placetheowcontrolleverintotheslotinthehopper.
Seegure8.
20.Placethecenterbraceintothehopper.Insertthe1/4"x
1-1/4"hexboltthroughthecenterbraceandthefrontof
thehopper.Assemblea1/4"atwasher,theowcontrol
leveranda1/4"nylockhexnutontothebolt.Do not
tighten yet.Seegure8.
21.Insertthe1/4"x3/4"hexboltthroughthecenterbrace
andtherearofthehopper.Assemblea1/4"atwasher
and1/4"nylockhexnutontothebolt.Tighten boththe
frontandrearbolts.Seegure8.
24.Movetheowcontrolleverasfarasitwillgotothe"OFF"
position.Pushthefeedplatebackasfarasitwillgoto
theclosedposition.Seegure10.
25.Placeanylonwasherontothebentendoftheowcontrol
linkandtheninsertthelinkintothefeedplatebracket.
Secureitwitha3/32"x3/4"cotterpin.Seegure10.
26.Tightenthelower1/4"hexnutuntilittouchesthebottom
oftheferrule,thentightentheupper1/4"nylockhexnut
untilitissnugagainstthetopoftheferrule.Seegure
10.
27.Hookthe open end of the spring into the feedplate.
Placetheclosedendofthespringontotheendofthe
hexboltintheowcontrollever.Secureitwitha1/4"
nylockhexnut.Seegure10.
28.Openandclosethefeedplateusingtheowcontrollever.
Checktomakesurethefeedplateisclosedcompletely
whentheleverisinthe"OFF"position.Ifthefeedplate
doesnotclosecompletely,adjustthe1/4"nylockhex
nutsontheowcontrollink.Seegure10.
ENGLISH
7
FIGURE 11
30.Installaangebearingintotheatsideofeachspike
disk,asshowningure12.
FIGURE 12
31.Installangedbearingsintobothoftheendplates.See
gure13.
32.Place the 1/4" thick spacer onto the spike disk shaft
andtheninserttheshaftthroughtheangedbearingin
thelefthandendplate.Seegure13.
SPIKE DISK
(CC) LONG SPACER TUBE
33.Placeashortspacertube,adrivedisk,a5/8"atwasher,
anotherdrivediskandasecond5/8"atwasherontothe
shaft.Fittheshortspacertubeontotheangedbearing
intheendplate.Seegure14.
FIGURE 13
FIGURE 14
FIGURE 15
IMPORTANT: Thenecksofthespikedisksinthefollowing
assemblyinstructionsmustfacetowardeachother.
34.Placetwospikedisks,separatedbyalongspacertube,
ontotheshaft.Fitthelongspacertubeontotheendsof
theangedbearingsinthedisks.Seegure15.
DRIVE DISKS
(T) 5/8" FLAT WASHER
(BB) SHORT SPACER
TUBE
(Y) FLANGED
BEARING
(Y) FLANGED
BEARING
(AA) 1/4" THICK
SPACER
SPIKE DISK SHAFT
HINT: In the next two steps, place the bearing on a at
surfaceandpressthediskdownontoit.
29.Installtwoangebearingsintoeachofthedrivedisk
assemblies.Seegure11.
ENGLISH
(Y) FLANGED
BEARING
(Y) FLANGED
BEARING
DRIVE DISK
ASSEMBLY
(Y) FLANGED
BEARING
SPIKE DISK
8
(T) 5/8" FLAT
WASHER
(Z) COMPRESSION
SPRING
35.Placea5/8"atwasher,thecompressionspringand
another5/8"atwasherontotheshaft.Seegure16.
SPIKE DISK
(CC) LONG SPACER TUBE
36.Placetwospikedisks,separatedbyalongspacertube,
ontotheshaft.Fitthelongspacertubeontotheendsof
theangedbearingsinthedisks.Seegure17.
FIGURE 16
FIGURE 17
37.Placetwo5/8"atwashersseparatedbyalongspacer
tubeontotheshaft.Seegure18.
FIGURE 18
(CC) LONG SPACER TUBE
(T) 5/8" FLAT WASHER
SPIKE DISK
(CC) LONG SPACER TUBE
FIGURE 19
38.Placetwospikedisks,separatedbyalongspacertube,
ontotheshaft.Fitthelongspacertubeontotheendsof
theangedbearingsinthedisks.Seegure19.
ENGLISH
9
FIGURE 23
41.Placeoneortwo5/8"atwashersontotheendofthe
spikediskshaftandsecuretheshaftwitha1/8"x1-1/2"
cotterpin.Seegure22.
42.Fastenthetwodrivediskstotheshaftusingtwo1/8"x
1-1/2"cotterpins.Seegure22.
FIGURE 22
39.Placetwo5/8"atwashersseparatedbyalongspacer
tubeontotheshaft.Seegure20.
FIGURE 20
SPIKE DISK
(BB) SHORT SPACER TUBE
40.Placeaspikediskandashortspacertubeontotheshaft.
Fittheshortspacertubeontotheendsoftheanged
bearingsinthespikediskandintheendplate.Pushthe
shaftonthroughtheangedbearingintheendplate.
Seegure21.
(CC) LONG SPACER TUBE
(T) 5/8" FLAT WASHER
FIGURE 21
43.Removethe connectinglink from the chain and then
assemblethechainontothetwosprocketsontheleft
sideofthehopper.Fastentheendsofthechaintogether
usingtheconnectinglink.Seegure23.
44.Placethechaincoveroverthechainandfastenittothe
hopper end plate using two selftapping screws.See
gure23.
ENGLISH
CONNECTING
LINK
(X) CHAIN
(J) SELF
TAPPING
SCREW
10
APPLICATION TIPS
1. Tohelppreventgranularmaterialfromcompactingand
cloggingthehopper,avoidunnecessarytowingwhen
thehopperowplatesareclosed.
2. Reducetheowsettingforspeedsslowerthan
3M.P.H.andincreasethesettingforhigherspeeds.
3. Toavoidmissesorstriping,overlapthepreviouswheel
tracksbyapproximately5"to6".
4. Foreasiestapplication,rstapplymaterialacrossboth
endsofthearea.Twoorthreepassesoneachendare
sufcient.Thenapplymaterialbackandforthasshown.
Usetheendareasforturningaround,shuttingoffthe
spreaderasyouentertheendareasandturningthe
spreaderonagainasyourleavetheendareasforyour
nextpass.Seegure25.
5. Iflawnisoddshaped,spreadaborderaroundtheedges
andthenspreadbetweentheborder.
6. Becarefulwhenspreadingaroundornamentalplants
because weed control chemicals can damage these
plants.
FIGURE 25
MAINTENANCE
1. Checknutsandboltsfortightnessbeforeeachuse.
2. Alwaysempty hopperafter eachuse,storingleftover
materialinit'soriginalbag.
3. Washanddrythoroughlyaftereachuse.
4. Applyalightcoatofoilonexposedmetalpartstohelp
preventrust.
5. Atleastonceayear,applyafewdropsofoiltowheels
andtoplasticbearingsinspikedisks,atendsofaerator
shaftandatendsofhoppershaft.
6. Cleanandoildrivechainonceayear.
Spikepointsaresharp.Exercisecautionwhen
handlingorworkingnearspikedisks.
OPERATION
HOW TO USE YOUR SPIKER/SPREADER
1. Refertotheinstructionlabelonthematerialpackage
andtotheinstructiondecal onyourspreader tohelp
determinetheproperspreadersettingandapplication
rate.AlsoseetheSettingChartonthispageforageneral
rangeofsettingsforcommonlyusedmaterials.
2. Determinetheapproximatesquarefootageofthearea
tobecoveredandestimatetheamountoffertilizeror
seedrequired.
3. Movethespreadertotheareawhereapplicationisto
begin.
4. Loosentheplasticwingnutandmoveittothedesired
setting.Retightenthenut.Seegure24.
5. Makingsuretheowcontrolleverisinthe"OFF"position,
llthehopper,breakingupanylumps.
6. Lowertheaeratorspikestotheoperatingposition.
7. Startthe spreader inmotion and then movethe ow
controllevertothe"ON"position(againsttheplasticwing
nut)asyoutravelacrossyourlawn.Therecommended
towingspeedis3m.p.h.
8. Donotmakesharpturnswithspikesintheground.
9. Raiseaeratorspikestotransportpositionwhencrossing
overconcreteorotherhardsurfaces.
10.Donotaerateifthegroundisextremelyhardordry.If
groundistoodry,sprinkleorwaterforonetotwohours
priortouse.
11.Donotaerateifthegroundistoowet(muddy).
IMPORTANT:Alwaysplaceowcontrolleverinthe"OFF"
positiontopreventexcessfertilizerfrombeingreleasedwhen
llingthespreaderandwhenstoppingorturning.
FIGURE 24
ALIGN AND TIGHTEN WING NUT
AT DESIRED FLOW SETTING
1
2
3
4
5
6
7
8
9
10
11
12
13
14
15
16 17
18
OFF
0
WING NUT SHOWN
AT FLOW SETTING "5"
Flow Rate Setting
MATERIAL TYPE At 3 M.P.H.
SETTING CHART
Fertilizer Granular/Pelleted 5-6 / 6-7
GrassSeed Fine/Coarse 5-6 / 7-8
3M.P.H.isequivalenttotraveling100feetin23seconds.
ENGLISH
Page is loading ...
Page is loading ...
Page is loading ...
Page is loading ...
Page is loading ...
Page is loading ...
Page is loading ...
Page is loading ...
19
REF. PART QTY DESCRIPTION
NO. NO.
REF. PART QTY DESCRIPTION
NO. NO.
1 47931 1 Hopper
2 24736 1 Endplate,RightHand
3 24735 1 Endplate,LeftHand
4 48418 12 Rivet,Pop
5 24747 1 Brace,Center
6 64104 1 Assembly,AgitatorShaft
7 47963 2 Bearing,HexFlange
8 24739 2 Blade,Agitator
9 47978 10 Screw,HexWasherHd,#8-32
10 R19172410 2 Washer,17/32"x1-1/2"x10Ga.
11 46838 2 Spacer,.8"I.D.x1"O.D.x.50"Lg.
12 R19171616 4 Washer,17/32"x1"x16Ga.
13 43093 3 Pin,Cotter1/8"x1-1/2"
14 45133 1 Spacer,.5"I.D.x1"O.D.x.59"Lg.
15 23520 1 Spacer,.66"I,D.x1.25"O.D.x.25"
16 47962 1 Spring,FlowPlate
17 64106 1 Assembly,SpikerShaft
18 64107 1 Assembly,TransportTube
19 24743 1 Lever,FlowControl
20 63956 2 DriveDiskAssembly
21 24332 7 Disk,Spike(7")
22 47953 1 Cover,Chain
23 47944 2 Tube,Hitch
24 24746 1 Lift,Handle
25 47961 2 Wheel,10"x1-5/8"
26 24741 1 Plate,Flow
27 23981 2 Bracket,Hitch
28 24539 1 Bracket,FeedPlate
29 41998 2 Rivet,Pop5/32
30 47960 1 ChainwithConnector
31 43848 1 Grip,ControlArm.187"x.75"
32 43943 1 Grip,HeightAdjustment32"/38"
33 47959 1 Link,FlowControl
34 47969 1 Ferrule,5/16"Threadx1/4"Hole
35 43224 3 Bolt,Hex5/16"x2-1/4"
36 44180 2 Bolt,Hex5/16"x2"
37 43085 2 Bolt,Hex5/16"x1-1/2"
38 43084 2 Bolt,Hex5/16"x1-3/4"
39 43063 1 Bolt,Hex5/16"x1"
40 44731 2 Screw,SelfTapping1/4"x1/2"
41 43012 1 Bolt,Hex1/4-20x3/4"
42 47810 10 Nut,NylockHex5/16"
43 47189 5 Nut,NylockHex1/4"
44 43088 2 Washer,Flat1/4"
45 43081 4 Washer,Flat5/16"
46 45100 2 Bolt,Hex1/2"x4"FullThread
47 43019 2 Nut,HexJam1/2"
48 48115 2 Nut,NylockHexJam1/2"
49 43343 1 Pin,HairCotter#4(1/8")
50 44101 1 Pin,Cotter3/32"x3/4"
51 47623 1 Pin,FlatHeadHitch,3/8"Dia.
52 44215 1 Bolt,Carriage5/16"x1-3/4"
53 712-0421 1 Nut,PlasticWing5/16"
54 1543-69 2 Washer,Nylon21/64"
55 46524 5 SpacerTube,Long
56 47777 1 Spring,Compression
57 46497 2 SpacerTube,Short
58 741-0249 13 Bearing,FlangedPV80.63I.D.
59 R19212016 10 Washer,Flat5/8"(21/32"x1-1/4")
60 1509-90 1 Bolt,Hex1/4-20x1-1/4"
61 1540-31 2 Washer,.78"x1.25"x.062"
62 46557 1 PushNut,1/2"
63 44137 5 Washer,Flat.518x1x.02
64 43178 1 Nut,Hex1/4"
42172 1 Owner'sManual
PARTS FOR 32" POLY SPIKER/SPREADER MODEL 45-0309-062
the fastest way to purchase parts
www.speedepart.com
REPAIR PARTS
Agri-Fab, Inc.
303WestRaymond
Sullivan,IL.61951
217-728-8388
www.agri-fab.com
the fastest way to purchase parts
www.speedepart.com
©2002Agri-Fab,Inc.
Thisdocument(ormanual)isprotectedundertheU.S.CopyrightLawsandthecopyrightlawsofforeigncountries,
pursuanttotheUniversalCopyrightConventionandtheBerneconvention.Nopartofthisdocumentmaybereproduced
ortransmittedinanyformorbyanmeans,electronicormechanical,includingphotocopyingorrecording,orbyany
informationstorageorretrievalsystem,withouttheexpresswrittenpermissionofAgri-Fab,Inc.Unauthorizedusesand/or
reproductionsofthismanualwillsubjectsuchunauthorizedusertocivilandcriminalpenaltiesasprovidedbytheUnited
StatesCopyrightLaws.
  • Page 1 1
  • Page 2 2
  • Page 3 3
  • Page 4 4
  • Page 5 5
  • Page 6 6
  • Page 7 7
  • Page 8 8
  • Page 9 9
  • Page 10 10
  • Page 11 11
  • Page 12 12
  • Page 13 13
  • Page 14 14
  • Page 15 15
  • Page 16 16
  • Page 17 17
  • Page 18 18
  • Page 19 19
  • Page 20 20

Agri-Fab 45-0309-062 User manual

Agri-Fab
Brand
Agri-Fab
Model
45-0309-062
Category
Spreader
Type
User manual
Download PDF
report

Ask a question and I''ll find the answer in the document

Finding information in a document is now easier with AI

in other languages

Related papers

Other documents