SENMAL FAAT2940 User manual
- Type
- User manual
32IN. SPIKE AERATOR
INSTRUCTION MANUAL
RULES FOR SAFE OPERATION
Remember,any power equipment can cause injury if operated improperly or if the user
does not understand how to operate the equipment.
Exercise caution at all times using power equipment.
1. Read the owners manual carefully for operating and service instructions before
attempting to assemble or operate this equipment. Be thoroughly familiar with the proper
use of this equipment.
2. Read the vehicle owners manual and vehicle safety rules,and know how to operate the
vehicle before using the equipment.
3. Never all children to operate the tractor or spike aerator attachment,and do not allow
adults to operate without proper instructions.
4. Wear eye protection when operating the aerator.
5. Wear substantial footwear when operating the aerator.
6. Keep the area of operation clear of all persons,particularly small children and also
pets.
7. Always begin with transmission in first (low) gear and engine at low speed, and
gradually increase speed as conditions permit.
8. Do not allow anyone to ride or sit on spike aerator attachment frame or on towing
vehicle,
9. The vehicle braking and stability may be effected with the attachment of this
equipment. Be aware of changing conditions on slopes. Refer to safety rules in the vehicle
owner’s manual concerning safe operation on slopes.
10.Always operate up and down a slope,never across the face of slope.
11. This equipment should be operated at reduced speed on rough terrain,along creeks
and creek or a ditch.
12.Do not tow this equipment on a highway or any other public thoroughfare.
13.Follow the maintenance instructions as outlined in this owner’s Manual.
Carton contents
LOOSE PARTS IN CARTON
1. END PLATE 2.FRAME 3.SPIKE DISK 4.AXLE 5.HITCH BRACKET
6.HITCH MOUNT ARM 7. HARDWARE PACK
1
ASSEMBLY INSTRUCTIONS
TOOLS REQUIRED FOR ASSEMBLY
1) 9/16 inch wrench(For head of the bolts)
2) Adjustable wrench(Use for tighten the two nuts on the hitch)
3) Pliers
4) Hammer
Lay out and identify all parts and hardware as shown in the carton contents.
Cautions：THE SPIKE DISKS HAVE SHARP POINTS. TO AVOID INJURY.USE EXTRA
CARE WHEN HANDLING THE DISKS AND WHEN ASSEMBLING THE AERATOR.
1. Carefully press or hammer a flanged bearing into each spike disk as shown in figure 1.
FIGURE 1
2. Carefully press or hammer a flanged bearing into each end plate as shown in figure 2.
\
FIGURE 2
2
3. Insert the axle through one of the end plates and then assemble a short spacer
tube onto the axle. See figure 3.
4. Assemble the eight spike disks and seven long spacer tubes onto the axle,with a long spacer
tube between each pair of disks.see figure 3.
5. Finally.assemble a second short spacer tube onto the axle and then insert the axle though the
other end plate. See figure 3.
FIGURE 3
6. Assemble two flat washers onto each end
of the axle. Assemble a cotter pin through
each end of the axle,spreading the ends of
each pin.See figure 4.
FIGURE 4
3
7. Assembly the two frame angles to the
two end plates as shown in figure 5. Use
eight M8*20 bolts and eight M8 hex lock
nuts. Do not completely tighten at this
time.
FIGURE 5
8. At this time tighten the bolts assembled in step
3,making sure the frame in straight.
9. Attach two hitch arm mount brackets to the two
middle holes in the front frame angle as shown in
figure 6. Fasten each bracket with a M8*20 hex
bolts,and a M8 hex lock nut. Make sure the brackets
are aligned straight and then tighten. See figure 6.
FIGURE 6
10. Insert the two hitch mount arms through the slots in the rear frame
angle .Assemble the arms to the outside of the hitch arm mount brackets using two M8*25
carriage bolts,and two M8 hex lock nuts.Do not tighten at this time. See figure 7.
FIGURE 7
11. Assemble the ends of the hitch mount arms
together using two 8*30 hex bolts,and two M8
hex nuts.Do not tighten at this time.
12. Assemble the hitch brackets to the hitch
mount arms using two M8*50 hex bolts,and
two M8 hex lock nuts.Tighten four M8 hex lock
nuts on the hitch.
13. Tighten the carriage bolts assembled in step
10.The hitch mount arms should be positioned
so that the aerator is approximate-
ly level when mounted to the tractor hitch.
Last step, tighten all hardware.
OPERATION
For best performance of spike aerator
Attachment the following lawn preparation
And operating procedures is recommended.
CAUTION:
SPIKE DISKS HAVE SHARP POINTS.EXERCISE CAUTION AT ALL TIMES WHEN USING THE
AERATOR.
4
1. Mow lawn and remove loose clippings
Prior to use of lawn aerator.
2. Start tractor engine with controls in neutral and place throttle at slow engine speed.
3. Engage shift lever into lowest possible forward speed and increase speed as conditions
permit.
4. Aerate in straightest line possible making overlapping passes to increase spike point pattern.
5. To prevent lawn damage. Do not turn sharply.
6. On sloped lawns aerate in up and down direction. Do not aerate across the face of slopes.
7. Aerating cuts small holes in the soil to create reservoirs that bring oxygen,fertilizer and water
into the root zone.
8. To increase spike point depth penetration add weight as required. The frame holds up to
Three concrete blocks at approximately 35 pounds. Weights can be secured to frame with
straps or other binding material.
9. If ground is extremely hard or dry, it is recommended that it be watered down for one or two
hours prior to use.
10. Do not attempt to aerate if ground is
Muddy.
MAINTENANCE
1. Spike points can be sharpened with a small grinder periodically to maintain good penetration.
Points should be removed to sharpen.
2. Before each use check nuts and bolts for tightness.
3. If rust appears on shield or spikes ,sand lightly and coat with enamel paint.
4. Always store in dry area and coat with light oil when not in use.
PARTS DRAWING
5
PART#
Description
Qty
PART #
Description
Qty
1
Angle Frame
2
11
Bracket, Hitch
2
2
Disc,Spike
8
12
Arm,Hitch Mount
2
3
Tube Spacer
7
13
Bracket,Hitch Arm Mount
2
4
Bearing,Flanged
10
14
Carriage Bolt M8*25
2
5
Axle
1
15
Hex Bolt M8*30
2
6
End Plate
2
16
Hex Bolt M8*50
2
7
Pin
2
17
Spacer,Tube
2
8
Hex Bolt M8*20
10
18
Hitch Pin
1
9
Hex Lock Nut M8
16
19
“R” Pin
1
10
Flat washer φ16
4
-
1
-
2
-
3
-
4
-
5
-
6
-
7
SENMAL FAAT2940 User manual
- Type
- User manual
Ask a question and I''ll find the answer in the document
Finding information in a document is now easier with AI
Other documents
-
Agri-Fab 45-0510 User manual
-
Craftsman 36 in. Spike Aerator User manual
-
-
-
Craftsman 48624372 Owner's manual
-
-
-
-
-