Cliffride 19003 Installation guide

Brand
Cliffride
Model
19003
Type
Installation guide

Cliffride 19003 is an easy-to-install light bar mounting kit that allows you to mount a 31-inch LED light bar to your vehicle. The kit includes all the necessary hardware, including a cowl bracket, light bar wire harness, and Phillips screws. The installation process is relatively simple and can be completed in under an hour with the right tools. Once installed, the Cliffride 19003 will provide you with additional lighting for off-roading, camping, or other activities.

Cliffride 19003 is an easy-to-install light bar mounting kit that allows you to mount a 31-inch LED light bar to your vehicle. The kit includes all the necessary hardware, including a cowl bracket, light bar wire harness, and Phillips screws. The installation process is relatively simple and can be completed in under an hour with the right tools. Once installed, the Cliffride 19003 will provide you with additional lighting for off-roading, camping, or other activities.

INS 19003
Cliffride - Rancho Cucamonga, CA 91730 – Tech@cliffride.com
05/9/16
Tools Needed
> Small flathead and phillips screwdrivers >< Needle nose plyers >< T30 torx bit >< 13mm wrench or socket <
Check fit all products before doing any body work or modifications if there is an issue contact us first
1. Remove the four T30 Torx bits holding the cowl in place. Fig. A
2. Remove the plastic caps covering the wiper hardware. Fig. B
3. Remove the 13mm nuts holding the wipers in place. Fig. C
4. Remove the wipers by pulling up and straight out. Fig. D
5. Lift the hood and remove the two tree rivets holding the cowl screen in place. Fig. E
6. Close the hood and remove the factory cowl. Fig. F
7. Using a flathead screw driver gently start to remove the tree rivets. Fig. G
8. Once the tree rivet is lifted enough remove it with a pair of needle nose plyers. Fig. H
9. Remove the four 13mm bolts from hood bracket. Fig. I
10. Reinstall the factory cowl vent screen and install the cowl bracket loosely so it can be moved side to side. Fig. J
11. Test fit the cowl and note the measurements of the cowl bracket. Fig. K
12. Tighten the four 13mm hood bracket bolts and install the supplied light bar to the bracket. Fig. L
13. Attach the cowl to the cowl bracket using the 2 phillips screws and plastic washers provided Fig. M
14. Tighten the cowl in place using the four T30 Torx screws. Fig. N
15. Attach the wipers in place using the factory hardware. Fig. O
16. Install the factory wiper cowers. Fig. P
17. Install the factory tree rivets into the cowl screen. Fig Q
19003 Bill of Materials
1
31in LED Light Bar
1
Cliffride cowl
1
LED Light wire harness
1
Cowl bracket
2
Plillips screws
2
Plastic washers
INS 19003
Cliffride - Rancho Cucamonga, CA 91730 – Tech@cliffride.com
05/9/16
Fig. A
Fig. B
Fig. C
Fig. D
Fig. E
Fig. F
INS 19003
Cliffride - Rancho Cucamonga, CA 91730 – Tech@cliffride.com
05/9/16
Fig. G
Fig. H
Fig. I
Fig. J
Fig. K
Fig. L
INS 19003
Cliffride - Rancho Cucamonga, CA 91730 – Tech@cliffride.com
05/9/16
Fig. M
Fig. N
Fig. O
Fig. P
Fig. O
Fig. Q
Fig. O
  • Page 1 1
  • Page 2 2
  • Page 3 3
  • Page 4 4

Cliffride 19003 Installation guide

Brand
Cliffride
Model
19003
Type
Installation guide

Cliffride 19003 is an easy-to-install light bar mounting kit that allows you to mount a 31-inch LED light bar to your vehicle. The kit includes all the necessary hardware, including a cowl bracket, light bar wire harness, and Phillips screws. The installation process is relatively simple and can be completed in under an hour with the right tools. Once installed, the Cliffride 19003 will provide you with additional lighting for off-roading, camping, or other activities.

Download PDF
report

Ask a question and I''ll find the answer in the document

Finding information in a document is now easier with AI

Related papers

Other documents