Cliffride Jacoby Fluid Containers Installation guide

Brand: Cliffride

Model: Jacoby Fluid Containers

Type: Installation guide

Cliffride Jacoby Fluid Containers:

These containers are designed to securely hold fluids and can be mounted on a variety of surfaces using the included bracket and strap. The containers come with a lock and key set for added security, and the lock will free spin when locked.

The containers are made of durable materials and are resistant to rust and corrosion. They are also easy to clean and maintain.

The Cliffride Jacoby Fluid Containers are ideal for storing and transporting a variety of fluids, including water, oil, and gasoline. They are also great for use in workshops, garages, and other industrial settings.

Cliffride Jacoby Fluid Containers:

The containers are made of durable materials and are resistant to rust and corrosion. They are also easy to clean and maintain.

INS 19012/19013

Cliffride - Rancho Cucamonga, CA 91730 – Tech@cliffride.com

09/01/16

Tools Needed

< Razor blade >< Marker >< Drill wit ¼ & 3/8 drill bits >< 10 & 14mm wrenches >< Allen wench set >

1. Attach the large gasket to the back of the container bracket than cut a small hole for the center bolt. Fig. A

2. Hold the bracket in place and mark the location in the center hole. Fig. B

3. Drill a ¼ pilot hole followed up by a 3/8 hole. Fig. C

4. Using a 10 and 14mm wrench tighten the rivet nut until the tool can be removed without the insert spinning the

threads should be in the center of the insert. Fig. D & Fig. E

5. Attach the bracket using the supplied allen screw and washer. Fig. F

6. Using the bracket as a template, drill the remaining 4 pilot holes using a 1/4in drill bit. Fig. G

7. Remove the bracket and drill out the remaining holes to 3/8. Fig. H

8. Install the remaining rivet nuts onto the fender following the same procedure in step 4. Fig. I

9. Slide the M10 bolt through the bracket before attaching the bracket onto the fender. Fig. J

10. Attach the bracket to the fender using the supplied 5 Allen screws and washers. Fig. K

11. Install the base plate gasket onto the container bracket. Fig. L

12. Install the strap gasket about an inch down from the 90* bend. Fig. M

13. Install the fluid container onto the tray. Fig. N

14. Tighten the bottle onto the bracket using the supplied lock, the lock will free spin when locked. Fig. O

19012/19013 Bill of Materials

Fluid Container with cap

¼ x 20 Allen Screws

Rivet Nut Tool

Container Bracket and strap

¼ Washers

¼ x 20 Rivet Nuts

M10 x 50 bolt

Lock with key set

Container gaskets

INS 19012/19013

Cliffride - Rancho Cucamonga, CA 91730 – Tech@cliffride.com

09/01/16

Fig. A

Fig. B

Fig. C

Fig. D

Fig. E

Fig. F

INS 19012/19013

Cliffride - Rancho Cucamonga, CA 91730 – Tech@cliffride.com

09/01/16

Fig. G

Fig. H

Fig. I

Fig. J

Fig. K

Fig. A

Fig. L

INS 19012/19013

Cliffride - Rancho Cucamonga, CA 91730 – Tech@cliffride.com

09/01/16

Fig. M

Fig. N

Fig. O

Cliffride Jacoby Fluid Containers Installation guide

Brand: Cliffride

Model: Jacoby Fluid Containers

Type: Installation guide

Cliffride Jacoby Fluid Containers:

The containers are made of durable materials and are resistant to rust and corrosion. They are also easy to clean and maintain.

Download PDF

report

Cliffride Jacoby Fluid Containers Installation guide

Cliffride Jacoby Fluid Containers Installation guide

Related papers

Other documents