2. Yamaha
  3. IN-TSK-Y-RMAX-007

Yamaha IN-TSK-Y-RMAX-007 Installation guide

  • Hello! I've reviewed the installation instructions for the SuperATV Turn Signal Kit for the CFMOTO UFOCE 1000. This document details the step-by-step process of installing the kit, including wiring, switch mounting, and LED signal setup. I'm ready to assist with any questions you have regarding the installation process or the kit's components.
  • What should I do before drilling holes?
    What should I use on all connections?
    Where should I consult for making connections?
© 2023 SuperATV.com®. All Rights Reserved. IN-TSK-Y-RMAX-007 9/12/2023
INSTALLATION INSTRUCTIONSINSTALLATION INSTRUCTIONS
Read instructions and view illustrations before beginning.
Plug and Play Turn Signal Kit:
for CFMOTO UFOCE 1000
Wire Ties
Horn Kit
2753 Michigan Road • Madison, Indiana 47250 • 855-743-3427
Thank You
For Choosing
Need help with your installation?
www.superatv.com
8:00am - 8:00pm EST M-Th
8:00am - 7:00pm EST Friday
9:00am - 2:00pm EST Saturday
sales@superatv.com
1-855-743-3427
Hazard and Horn Switch
4x - LED Signal
Turn Signal Switch
ECU
- Do not discard packaging until product has been successfully installed.
- Components may be installed in locations other than where shown. Alway verify wire harness length.
- While routing, follow factory wiring when possible.
- Use provided dielctric grease on all connections.
- Always consult labels on Harnesses when making connections.
- Avoid rotating or hot components when securing.
- Before drilling any holes, check behind area to be drilled for any interference.
2
IN-TSK-Y-RMAX-007
to ECU
to LED’ s
to Horn
to Turn Signal Switch to Horn / Hazard Switch
to License Plate Light
(opt)
to Left Rear Tail Light
to Right Rear Tail Light
to rear of machine
green and black wires = right
yellow and black wires = left
3
IN-TSK-Y-RMAX-007
Remove Accessory Panel.Remove Accessory Panel.
- Place Harness into compartment.- Place Harness into compartment.
- Route Switch portions of Harness to Dash area (see page 10).- Route Switch portions of Harness to Dash area (see page 10).
- Route Rear portion of Harness (see page 2) to rear of machine.- Route Rear portion of Harness (see page 2) to rear of machine.
Reinstall Accessory Panel.
4
IN-TSK-Y-RMAX-007
(passenger)(passenger)
Look up and into area shown to access rear stock Harness. Driver side is same.Look up and into area shown to access rear stock Harness. Driver side is same.
Rear
5
IN-TSK-Y-RMAX-007
Unplug Tail Light.Unplug Tail Light.
Connect Harness.Connect Harness.
(passenger)(passenger)
(passenger)(passenger)
Rear continued
6
IN-TSK-Y-RMAX-007
Rear continued
Unplug Tail Light.Unplug Tail Light.
(driver)(driver)
(driver)(driver)
Connect Harness.Connect Harness.
7
IN-TSK-Y-RMAX-007
2x - Self Tapping Screw2x - Self Tapping Screw
ECUECU
- Plug in Harness and secure ECU to Accessory Panel with hardware shown; tighten.
- Locate stock connector shown.
stock connector with brown stock connector with brown
and black wiresand black wires
8
IN-TSK-Y-RMAX-007
LED Signals:
- Usermayinstallinlocationsdierentthanshown.
- Drill a Ø3/4” hole in body and install LED Signal. Repeat for remaining LED Signals.
- Plug LED Signals into corresponding inputs on Harness.
- Secure all Wires as needed.
LED
Gasket
- Separate LED from Gasket.
- Install Gasket into hole.
- Install LED into Gasket.
If Light is hard to insert
separate as shown.
Before drilling any holes, check behind area to be drilled for any interference.
LED SignalLED Signal
LED SignalLED Signal
9
IN-TSK-Y-RMAX-007
Horn:
- UsermayinstallHorninlocationdierentthanshown.
- Install Horn to Bracket.
- Connect Harness to Horn.
- Secure to location shown; tighten.
HornHorn
Secure Horn with stock hardware.Secure Horn with stock hardware.
(driver)(driver)
Horn BracketHorn Bracket
10
IN-TSK-Y-RMAX-007
SuperATV recommends testing Switches before permanently mounting.
- Connect Harnesses to Switches.
- Secure Switches.
Remove (2) Knockouts for Switches.Remove (2) Knockouts for Switches.
Verify that wiring will reach mounting locations. Verify that wiring will reach mounting locations.
11
IN-TSK-Y-RMAX-007
Carefully cut Heat Shrink. as shown, and push mesh back to expose wires.Carefully cut Heat Shrink. as shown, and push mesh back to expose wires.
Cut yellow wire only and strip approximately Cut yellow wire only and strip approximately
1/4” from both ends.1/4” from both ends.
Twist both ends together.Twist both ends together.
Cut green wire on Right Turn Signal Harness.Cut green wire on Right Turn Signal Harness.
Left Turn Signal Harness shown in illustrations.
Accessory to Turn Signal Kit Wiring
12
IN-TSK-Y-RMAX-007
Install Connector and crimp.Install Connector and crimp.
- Cut “+” positive (white wire in SuperATV’s example) - Cut “+” positive (white wire in SuperATV’s example)
from accessory and strip approximately 1/4” from end.from accessory and strip approximately 1/4” from end.
- Insert into Connector and crimp.- Insert into Connector and crimp.
SuperATV recommends using a handheld mini torch, or lighter, to activate heat shrink on Connector.
Accessory to Turn Signal Kit Wiring continued
/