IN-TSK-P-PROXP-004

SuperATV IN-TSK-P-PROXP-004 User manual

  • Hello! I'm a chat assistant and I've reviewed the provided Installation Instructions for the SuperATV Turn Signal Kit PRO XP. This document outlines the installation of a turn signal kit for Polaris RZR PRO XP, including a hazard light switch, horn kit, turn signal switch, and LED signals. I'm ready to answer your questions about this kit or the installation process.
  • What is included in the kit?
    What should I do before installing the kit?
    What is the legal responsibility of the Buyer?
© 2020 SuperATV.com®. All Rights Reserved. Rev IN-TSK-P-PROXP-004 12/15/2021
INSTALLATION INSTRUCTIONS
Read instructions and view illustrations before beginning.
Plug and Play Turn Signal Kit:
for Polaris RZR® PRO XP
Wire Ties
Horn Kit
2753 Michigan Road • Madison, Indiana 47250 • 855-743-3427
Thank You
For Choosing
Need help with your installation?
www.superatv.com
8:00am - 8:00pm EST M-Th
8:00am - 7:00pm EST Friday
9:00am - 2:00pm EST Saturday
sales@superatv.com
1-855-743-3427
Hazard Light Switch Horn Switch
4x - LED Signal
Components may be installed in locations other than where shown. Alway verify wire harness length.
CUSTOMER NOTIFICATION AND DISCLAIMER LIABILITY
This product is a modication for utility task vehicles and all terrain vehicles. Use this product at your own risk.
Warranty and Liability Limitations. The Buyer hereby assumes all risks associated with the use and/or installation of this product. Buyer waives all liability claims against
SuperATV® of any kind or nature, including, but not limited to, liability for penalties, nes, property damage, personal injury or death, to the fullest extent permitted by law. Buyer
acknowledges and agrees that SuperATV® is not liable for any direct, indirect, incidental, consequential or special damages, including but not limited to, damage, loss of life, loss
of property or equipment, loss of prots or revenue, injury, or claims from any individual or entity arising from the use of this product.
The warranty for this product, if any, may give you (“Buyer”) specic legal rights, and Buyer may also have other rights which may vary from state to state. The installation of this
product may void or otherwise adversely aect your factory warranty.
Consult your vehicle warranty before using this Product. Under no circumstances will SuperATV® be liable for the voidance of the Buyer’s vehicle warranty. Buyer assumes all risk
and responsibility if a manufacturer and/or dealer voids the Buyer’s vehicle warranty due to use of this Product.
Safety and Laws. Operate your vehicle at all times in a safe manner. You must abide by all local, state, and federal laws, including but not limited to vehicle safety, trac laws,
and ordinances. It is your responsibility to know the laws and how they apply to you. The installation of this product may violate certain local, state, and federal laws. Be advised
that laws vary depending on town, city, county, state, etc. Use of this product on public streets, roads, or highways may be in violation law. The Buyer is solely and exclusively
legally and personally responsible for any violation of the law by the installation or use of this product. In no case will SuperATV® be held liable if Buyer violates the law or uses
the product in an unsafe manner.
The Buyer is responsible to fully understand the capability and limitations of his/her vehicle according to manufacturer specications, warnings and instructions and agrees to hold
SuperATV® harmless from any damage resulting from failure to adhere to such specications, warnings and/ or instructions. The Buyer is also responsible to obey all applicable
federal, state, and local laws when operating his/her vehicle while using this product, and the Buyer agrees to hold SuperATV® harmless from any violation thereof.
Installation. The installation of this product on your vehicle indicates that you have had the opportunity to inquire about applicable local, state, and federal laws and ordinances
and that you have read and understand, and accept all of the terms of, this Disclaimer.
SuperATV® shall not be responsible for the proper installation, use, and service of this product. Rather, the Buyer shall be solely responsible for the installation of the product and
any damage that may be done to the vehicle or vehicle components as a result of modications made by the Buyer.
Do not discard packaging until product has been successfully installed.
Turn Signal Switch
(does not have a backlight)
2
IN-TSK-P-PROXP-004
- While routing, follow factory wiring when possible.
- Avoid rotating or hot components when securing.
- Left = Driver Side - Right = Passenger Side
Front Harness
use provided dielctric grease
on all connections
to rear of machine
Rear Harness
to front of
machine
Always consult labels on
Wiring Harnesses when
making connections.
Main Harness
to Center Console
to Gauge Pod
to Center Console
to Center Console
to Dash Storage Bin
3
IN-TSK-P-PROXP-004
remove Cup Holder
(passenger) (driver)
remove Dash Storage Bin
remove Storage Bin
4 seat models require additional removal steps; see pages 15 - 17
4
IN-TSK-P-PROXP-004
(passenger Footwell)
Control Box
- Secure Control Box to Firewall with hardware shown.
2x - #8-18 x 3/16”
2x - #8-18 x 3/4”
connect “12V Switched Terminal Block”
from Main Harness to location shown
5
IN-TSK-P-PROXP-004
Rear Harness:
- Route Rear Harness to rear of machine as shown.
(passenger)
Rear Harness (use a wire shing tool)
(passenger)
Front Harness through Grommet
plug Front Harness into Control Box
Front Harness:
- Route Front Harness to front of machine as shown.
6
IN-TSK-P-PROXP-004
unplug stock harness
(driver)
REAR
route Rear Harness through here
- Unplug stock harness from location shown.
Rear Harness continued:
- Route Rear Harness to rear of machine as shown.
4 seat models require additional Rear Harness routing; see pages 18 - 19
7
IN-TSK-P-PROXP-004
(driver)
REAR
plug stock harnesses
into Rear Harness
optional License Plate Light wiring
Rear Harness
Rear Harness continued:
- Connect Rear Harness as shown.
- Secure all Wires as needed.
8
IN-TSK-P-PROXP-004
(driver)
remove “INSTR UNSW 7.5A” Fuse
FUSE MUST BE REMOVED BEFORE CONTINUING
9
IN-TSK-P-PROXP-004
PIN 6 PIN 7
GREEN TO PIN 6
YELLOW TO PIN 7
disconnect from Gauge Pod
open Housing and remove Plugs shown
connect “Indicator Lights” from Main Harness
to locations shown
Indicator Lights:
10
IN-TSK-P-PROXP-004
Indicator Lights continued:
close Housing and reconnect to Gauge Pod
REINSTALL PREVIOUSLY REMOVED FUSE
11
IN-TSK-P-PROXP-004
LED Signal:
- Drill a Ø3/4” hole in body and install LED Signal. Repeat for remaining LED Signals.
- Plug LED Signals into corresponding inputs on Front Harness.
- Secure all Wires as needed.
LED
Gasket
- Separate LED from Gasket.
- Install Gasket into hole.
- Install LED into Gasket.
If Light is hard to insert separate as shown.
(passenger)
LED Signal
LED Signal
Before drilling any holes, check behind area to be drilled for any interference.
12
IN-TSK-P-PROXP-004
Actuator
TERMINAL 7 AND ARROW MUST BE ORIENTED AS SHOWN
Rotate Actuator 180°
- Gently pry one side up.
- Pry opposite up and remove Actuator.
- Rotate and snap Actuator into place.
Switch Orientation
13
IN-TSK-P-PROXP-004
Switch Mounting:
- User may install Switches in locations dierent than shown.
- Verify that Wire Harness will reach Switches before mounting.
SuperATV recommends testing Switches before permanently mounting.
remove stock Switch Covers
push appropriate Wire Harness
connections through openings
connect Switches to Wire Harness connections
Horn:
- User may install Horn in location dierent
than shown.
- Illustration is SuperATV’s choice.
- Install provided Horn Bracket to Horn.
(passenger)
14
IN-TSK-P-PROXP-004
remove Hood
Horn
Horn
Horn Bracket
stock
connect “Horn” from Front Harness
to locations shown
(terminal connections are not relevant)
Horn Bracket
Horn
REINSTALL PREVIOUSLY REMOVED STOCK COMPONENTS
15
IN-TSK-P-PROXP-004
remove Storage Bin
remove Cup Holder
remove Seat backs
ip Seat bottoms
4 seat additional removal steps
16
IN-TSK-P-PROXP-004
disconnect Seat Belts
remove Top Closeo
remove Bottom Closeo
(passenger)
(driver)
17
IN-TSK-P-PROXP-004
remove Rear Console
remove Panel
(driver)
(driver)
18
IN-TSK-P-PROXP-004
(passenger)
(passenger)
Rear Harness
Rear Harness
4 seat Rear Harness routing
- Route Rear Harness through Storage Bin opening.
- Route Rear Harness to Closeos opening.
19
IN-TSK-P-PROXP-004
(driver)
(driver)
Rear Harness
- Route Rear Harness up and into Clutch Cover area.
- Return to page 6 and continue installation.
Stock Harness
/