BMW Z3 coupe Installation Instructions Manual

BMW
Brand
BMW
Model
Z3 coupe
Type
Installation Instructions Manual

This manual is also suitable for

BMW Z3 coupe is a retrofit hands-free kit for Ericsson mobile phones Series T39 that helps the driver to easily connect their phone to the car's audio system, allowing them to make and receive calls without having to hold the phone. It also features a built-in microphone and speaker for clear audio quality, and an adhesive windscreen aerial for improved signal reception. The kit is designed for quick and easy installation, and includes all necessary hardware and instructions.

BMW Z3 coupe is a retrofit hands-free kit for Ericsson mobile phones Series T39 that helps the driver to easily connect their phone to the car's audio system, allowing them to make and receive calls without having to hold the phone. It also features a built-in microphone and speaker for clear audio quality, and an adhesive windscreen aerial for improved signal reception. The kit is designed for quick and easy installation, and includes all necessary hardware and instructions.

Retrofit kit No. 84 64 0 147 581
Installation Instructions No. 01 29 0 147 585 Issue date: 02.2002
Retrofit hands-free kit for Ericsson mobile phones Series T39
BMW Z3 (E
36/7) roadster and coupé
The installation time is approx. 2 hours, but this may vary depending on the condition of the car and the
equipment in it.
Retrofit kit No. 84 64 0 147 581
Parts and Accessories
Installation Instructions
EN/2
Retrofit kit No. 84 64 0 147 581
Installation Instructions No. 01 29 0 147 585 Issue date: 02.2002
Contents
Section Page
Important information. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 3
1. Preparations. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 4
2. Parts list . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 5
3. Hands-free kit connection overview . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 6
4. Installation and cabling diagram . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 7
5. To install and connect the wiring harness . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 8
6. To install the speaker . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 9
7. To install the hands-free microphone and adhesive windscreen aerial . . . . . . . . . . . . . . . . . . . . . . . 10
8. To install the telephone console and hands-free control module . . . . . . . . . . . . . . . . . . . . . . . . . . . 11
9. Concluding work . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 14
10. Hands-free kit circuit diagram . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 15
EN/3
Retrofit kit No. 84 64 0 147 581
Installation Instructions No. 01 29 0 147 585 Issue date: 02.2002
Important information
Only for use in the BMW dealer organisation.
Subject to technical modifications.
If the specified PIN chambers are occupied, bridges, double crimps or twin-lead terminals must be used.
This system does not require coding
Installation information
Before starting the installation work clean the screen with conventional cleaning products.
Do not touch the adhesive strips and cleaned screen.
Never attempt to affix the adhesive screen aerial to a misted or damp screen.
The gluing temperature of the screen must be at least 20˚C.
The adhesive strip and adhesive screen aerial will bond immediately on contact and cannot be moved again.
To ensure a permanent bond allow the car to stand in an ambient temperature of at least 20˚C for approx.
two hours.
Ensure that the cables/lines are not kinked or damaged as you install them in the car.
Target group
The target group for these installation instructions is specialist personnel trained on BMW cars with the
appropriate specialist knowledge.
All work must be completed using the latest BMW repair manuals, circuit diagrams, servicing manuals and
work instructions in a rational order using the prescribed tools (special tools) and observing current health and
safety regulations.
Required special tools
DIS or MoDiC
EN/4
Retrofit kit No. 84 64 0 147 581
Installation Instructions No. 01 29 0 147 585 Issue date: 02.2002
1. Preparations
0
TIS instruction No.
Conduct a brief test ---
Disconnect the negative pole of the battery 12 00 ...
The following components must be removed first of all:
Glove box on the right 51 16 360
Sun visors, left and right 51 16 104
Interior rear-view mirror 51 60 063
Trim for the roof pillar, front left and right 51 43 201
Trim for the front headlining (windscreen panel, top) 51 44 150
Radio 65 51 030
EN/5
Retrofit kit No. 84 64 0 147 581
Installation Instructions No. 01 29 0 147 585 Issue date: 02.2002
2. Parts list
0
Legend
A Power supply wiring harness
B Mute circuit wiring harness
C Mobile phone holder
D Adhesive windscreen aerial
E Speaker
F Hands-free control module
G Hands-free control module holder
H Hands-free microphone
I Velcro tape
J Retaining plate for the mobile phone holder
K Telephone console, top section
L Telephone console, bottom section
MPlug contact (3x)
NPlug casing (3x)
O Socket contact (4x)
P Socket casing (3x)
Q Self-tapping screw 4 x 16 (4x)
R Self-tapping screw 4 x 46 (2x)
S Speed nut (2x)
J
H
I
F
G
M
O P
C
D
N
K
L
E
Q
R
S
A
B
EN/6
Retrofit kit No. 84 64 0 147 581
Installation Instructions No. 01 29 0 147 585 Issue date: 02.2002
3. Hands-free kit connection overview
0
0
0
Item Description Signal
Cable colour /
Cross-section
Connection location in the car Abbreviation / Slot
APower supply wiring harness --- --- --- ---
A1 Cable branch Earth BR
0.75 mm
2
With enclosed socket and plug contact on
radio plug
X18126
PIN 15
A2 Cable branch Terminal
30
RT
0.75 mm
2
With enclosed socket and plug contact on
radio plug
X18126
PIN 9
A3 2-pin SW plug --- --- To hands-free control module ---
B Mute circuit wiring harness --- --- --- ---
B1 Cable branch Mute SW
0.5 mm
2
With enclosed socket and plug contact to
the radio plug
X18126
PIN 4
B2 WS 5-pin plug --- --- To hands-free control module ---
A1
A2
B1 B2
A3
A
B
EN/7
Retrofit kit No. 84 64 0 147 581
Installation Instructions No. 01 29 0 147 585 Issue date: 02.2002
4. Installation and cabling diagram
0
Legend
0
1 Radio plug X18126
A Hands-free kit control module wiring harness
C Mobile phone holder
D Adhesive windscreen aerial
E Speaker
F Hands-free control module
H Hands-free microphone
1
A
E
D
B
G
C
EN/8
Retrofit kit No. 84 64 0 147 581
Installation Instructions No. 01 29 0 147 585 Issue date: 02.2002
5. To install and connect the wiring harness
0
0
0
0
0
Lay branches
A1 – A2
and
B1
to the radio plug
X18126
.
0
Connect branches
A1 – A2
as follows to the cables in
plug
X18126
:
-
A1
, SW cable, to BR cable PIN 15
-
A2
, RT cable, to RT/GN cable PIN 9
-
B1
, SW cable, to WS/SW cable PIN 4
See figure 036 0092 Z for the procedure
0
Cut the corresponding cable of the plug
X18126
at a
suitable point.
Crimp the socket contact
O
on to the cable end (2) of the
plug and connect the socket casing
P
.
Crimp the plug contact
M
on to the open cable end (5),
crimp on the corresponding branch (7) and connect the
plug casing
N
.
Connect the socket and plug casings.
X18126
B1
A1-A2
X18126
A1-A2
B1
7
2
5
P
O
N
M
EN/9
Retrofit kit No. 84 64 0 147 581
Installation Instructions No. 01 29 0 147 585 Issue date: 02.2002
6. To install the speaker
0
0
0
0
0
Unscrew both knurled-head bolts (1) and remove the
holder (2) from the speaker
E
.
Place speed nuts
S
on the holder (2).
0
Position the holder (2) on to the bottom trim (1) as shown
and mark it.
Drill the fastening holes with a 3.0 mm twist drill.
Secure the holder (2) with Philips screws and speed nuts
S
.
0
Drill the sound outlet holes (2) as shown in the bottom
trim (1) with a 16 mm peel drill.
0
Insert the speaker
E
into the bottom trim (1) so that
the speaker opening points towards the noise
outlet opening (3).
Insert the speaker
E
into the holder and secure it with the
knurled-head bolts (2).
2
1
E
S
036 0100
Z
2
S
1
2
1
E
1
2
3
EN/10
Retrofit kit No. 84 64 0 147 581
Installation Instructions No. 01 29 0 147 585 Issue date: 02.2002
7. To install the hands-free microphone and adhesive windscreen aerial
0
0
0
0
File out the cable passage hole (1) near the interior light
with a round file in the windscreen panel trim (2).
0
Clean the windscreen in the area where the aerial is to be
affixed, see “Important information”.
Remove the transparent backing foil from the adhesive
strip (1).
Affix the adhesive strip (1) to the left of the interior rear-
view mirror (2) from the inside on the windscreen (3).
Press out any air bubbles.
Remove the yellow backing foil from the adhesive strip (1).
Place the adhesive windscreen aerial
D
on to the
adhesive strip and press it into position for approx. 15
seconds.
0
Affix the hands-free microphone
H
to the windscreen
panel trim as shown using a Velcro fastener
I
.
Lay the aerial cable and microphone cable through the
opening you have filed out to the passenger side.
Do not damage the adhesive windscreen aerial and
the hands-free microphone as you install the sun
visors.
2
1
1
3
2
D
H
I
EN/11
Retrofit kit No. 84 64 0 147 581
Installation Instructions No. 01 29 0 147 585 Issue date: 02.2002
8. To install the telephone console and hands-free control module
0
0
0
0
0
Connect the bottom section of the telephone console
L
to the top section
K
.
Drill holes with a 3 mm twist drill and connect the bottom
section
L
and the top section
K
using Philips screws
Q
.
0
Drill the cable passage (1) for the mobile phone holder in
the bottom section of the telephone console
L
as shown
using a 22 mm peel drill.
0
Remove the bottom section (1) from the mobile phone
holder
C
.
0
Remove the Philips screw (1) and take the mobile phone
holder
C
off the retaining plate.
Q
L
K
1
L
ERICSSON
1
C
1
C
EN/12
Retrofit kit No. 84 64 0 147 581
Installation Instructions No. 01 29 0 147 585 Issue date: 02.2002
8. To install the telephone console and hands-free control module
0
0
0
0
0
Place the retaining plate
J
on the top section of the
telephone console
L
and mark the fixing holes.
Drill the holes with a 3 mm twist drill and secure the
retaining plate
J
with Philips screws (1).
0
Place the hands-free control module
F
on the holder
G
and mark the fixing holes.
Drill the holes with a 3 mm twist drill and secure the
hands-free control module
F
with Philips screws (1).
0
Connect the microphone cable plug (1), the speaker
cable plug (2), the mobile phone holder plug (3) and
branches
A
and
B
to the hands-free control module
F
.
0
Carefully push the trim (2) for the oddments box in the
passenger footwell to the side.
Remove the top retaining screw (1) from the mounting
support.
L
J
1
G
F
1
1
F
B
3
A
2
1
2
1
EN/13
Retrofit kit No. 84 64 0 147 581
Installation Instructions No. 01 29 0 147 585 Issue date: 02.2002
8. To install the telephone console and hands-free control module
0
0
Secure the hands-free control module and holder
G
to
the retaining screw (1).
Connect the aerial cable from the mobile phone holder (2)
and adhesive windscreen aerial (3).
0
Do not damage the cable as you secure the
telephone console.
Secure the mobile phone holder
C
to the retaining plate
using the Philips screw (1).
Secure the telephone console
L
using Philips screws
R
.
0
Position the bottom section (1) on the mobile phone
holder
C
.
G
1
2
3
R
L
1
C
ERICSSON
1
C
EN/14
Retrofit kit No. 84 64 0 147 581
Installation Instructions No. 01 29 0 147 585 Issue date: 02.2002
9. Concluding work
- Connect battery
- Conduct a brief test
- Conduct a function test
- Re-assemble the car
EN/15
Retrofit kit No. 84 64 0 147 581
Installation Instructions No. 01 29 0 147 585 Issue date: 02.2002
10. Hands-free kit circuit diagram
0
A1*
A2*
A3*
A4*
X1*
X2*
X3*
X4*
X5*
X6*
X7*
X8*
X18126
Y1*
EN/16
Retrofit kit No. 84 64 0 147 581
Installation Instructions No. 01 29 0 147 585 Issue date: 02.2002
10. Hands-free kit circuit diagram
Legend
All designations with an asterisk (*) only apply to these installation instructions and these circuit diagrams.
Cable colours
A1* Hands-free control module
A2* Hands-free microphone
A3* Speaker
A4* Mobile phone holder
X1* SW 2-pin pawl plug
X2* SW 2-pin pawl plug
X3* SW 10-pin plug
X4* WS 5-pin plug
X5* SW 2-pin plug
X6* Twin-lead terminal
X7* Twin-lead terminal
X8* Twin-lead terminal
X18126 Radio plug
Y1* To standard wiring harness
RT red
SW black
WS white
  • Page 1 1
  • Page 2 2
  • Page 3 3
  • Page 4 4
  • Page 5 5
  • Page 6 6
  • Page 7 7
  • Page 8 8
  • Page 9 9
  • Page 10 10
  • Page 11 11
  • Page 12 12
  • Page 13 13
  • Page 14 14
  • Page 15 15
  • Page 16 16

BMW Z3 coupe Installation Instructions Manual

BMW
Brand
BMW
Model
Z3 coupe
Type
Installation Instructions Manual
This manual is also suitable for

BMW Z3 coupe is a retrofit hands-free kit for Ericsson mobile phones Series T39 that helps the driver to easily connect their phone to the car's audio system, allowing them to make and receive calls without having to hold the phone. It also features a built-in microphone and speaker for clear audio quality, and an adhesive windscreen aerial for improved signal reception. The kit is designed for quick and easy installation, and includes all necessary hardware and instructions.

Download PDF
report

Ask a question and I''ll find the answer in the document

Finding information in a document is now easier with AI

Related papers

Other documents