Extron SMB 210 Series User manual

Brand: Extron

Model: SMB 210 Series

Type: User manual

Extron SMB 210 Series surface mount boxes are designed to mount Extron Flex55 mounting kits and EU devices. Available in various sizes, they can be set unattached on a table, fastened with screws, or clamped using the optional SMB Table Clamp Kit. The bottom plate includes a #6-32 stud insert and nut for grounding if necessary.

SMB 210 Series • Installation Guide

The Extron SMB 210 Series Surface Mount Boxes are designed for mounting Extron Flex55 mounting kits and EU devices. The

SMB 210 Series enclosures are available in various sizes and can be installed in any of three methods: set unattached on a table,

fastened to a table with screws, or clamped to a table using the optional SMB Table Clamp Kit. The bottom plate of each SMB

enclosure includes a #6‑32 stud insert and nut, if necessary for grounding.

This guide provides installation instructions for an experienced installer.

NOTE: Ensure that the installation meets the national, local, and state regulatory requirements, including building,

electrical, safety codes, and ADA accessibility requirements.

Setting SMB on a Table

Refer to Rear Panel Cabling on the next page to position

your cables. Place the enclosure in any convenient

location.

Fastening SMB to the Table

Find a suitable location for the enclosure. Position it and mark pilot hole locations for the two mounting holes. If desired, mark and

drill a cutout location for cable access or refer to Rear Panel Cabling.

SMB Table Clamp: Optional Accessory

As an option, the SMB Table Clamp Kit can be used

to anchor 1‑ to 4‑gang enclosures to the edge of a

table via non‑destructive means (no cutting, drilling,

no marring of table surface). Go to www.extron.com

for more information about the SMB Table Clamp Kit.

Fasten with supplied

#8 wood screws.

For standard mounting,

route the cables from

under the table.

Cable

Shield

Table

Clamp

Plastic

Rivet

Extron

VOLUME

VIDEO

DISPLAY

OFF

Mounting Hole

Drill 3/32" pilot holes for the

mounting holes.

Alternate Mounting Hole

Fasten with supplied

#8 wood screws.

For standard mounting,

route the cables from

under the table.

Cable

Shield

Table

Clamp

Plastic

Rivet

Extron

VOLUME

VIDEO

DISPLAY

OFF

Mounting Hole

Drill 3/32" pilot holes for the

mounting holes.

Alternate Mounting Hole

Fasten with supplied

#8 wood screws.

For standard mounting,

route the cables from

under the table.

Cable

Shield

Table

Clamp

Plastic

Rivet

Extron

VOLUME

VIDEO

DISPLAY

OFF

Mounting Hole

Drill 3/32" pilot holes for the

mounting holes.

Alternate Mounting Hole

68‑2874‑01

Rev. C

02 21

All trademarks mentioned are the property of their respective owners.

Worldwide Headquarters: Extron USA West, 1025 E. Ball Road, Anaheim, CA 92805, 800.633.9876

For information on safety guidelines, regulatory compliances, EMI/EMF compatibility, accessibility, and related topics, see the

Extron Safety and Regulatory Compliance Guide on the Extron website.

Remove the end cap by

rotating the front away

from the enclosure.

Use a small

screwdriver to

release tabs in

3 places.

Reinstall end cap.

Guide in front tabs.

Snap in rear tab

Cable Strain Relief

Cable Strain

Relief

Install the cable strain relief

and cover strips. The SMB 211

does not require the rear

cover strip.

Route cables through the

rear access panel and attach

to the strain relief with a zip tie.

Slide out rear cover strip

and either discard or break

apart at the score marks

as noted.

SMB 212 / 213 / 214

Break at Score Marks,

Discard Middle

Discard

SMB 211

Rear Panel Cabling

Extron SMB 210 Series User manual

Extron SMB 210 Series User manual

Extron SMB 210 Series User manual

Related papers

Other documents