Huawei 21501718 User guide

Brand: Huawei

Model: 21501718

Type: User guide

Huawei 21501718 is a smart module sliding door system designed for use in data centers and other IT environments. It features a robust construction with a steel frame and tempered glass door, providing excellent security and durability. The door is operated by a motorized mechanism that allows for smooth and quiet opening and closing.

The Huawei 21501718 sliding door system is highly customizable, with various options for door sizes, finishes, and locking mechanisms. It can be integrated with access control systems, magnetic locks, and other security features to meet specific requirements. Additionally, the system includes pre-installed cables for easy integration with other devices and systems.

安装下封板与内门框

Installing Bottom Sealing Plates and the Inner Door Frame

01 02 安装导轨

Installing a Guide Rail 03 安装胶条

Installing Rubber Strips

安装玻璃门和止摆器

Installing a Glass Door and Damper

04 （可选）安装电磁锁

(Optional) Installing a Magnetic Lock

步骤1：将内立柱与内门楣固定。步骤1：安装门胶条。

步骤1：将门推入导轨。

步骤2：将中间缓冲器弹簧拨到压缩状态。

步骤3：根据标签箭头方向，将端部缓冲器分别

推入导轨两端。

步骤4：固定导轨两端螺丝。

步骤5：将缓冲器往导轨末端推，直到紧贴导轨螺丝。

步骤6：在缓冲器弹簧压缩状态下，紧固缓冲器。

Step 4: Secure the screws at both ends of the guide rail.

Step 5: Push the buers to the ends of the guide rail until

they are in close contact with the guide rail screws.

Step 6: Secure the buers when the springs of the

buers are in the compressed state.

步骤1：将电磁吸铁固定角件与垫片固定在门板上。

步骤2：左右两侧的电磁吸铁分别紧固在固定角件上。

步骤3：拆除电磁锁附件，保留拆下的两颗螺钉。

步骤4：用螺钉将2个电磁锁分别固定在电磁锁固定件上。

步骤5：将组装完成的电磁锁固定在导轨上。

Step 1: Secure the magnet fastener and washer to

the door panel.

Step 2: Secure the magnets on the left and right

sides to the fasteners respectively.

Step 3: Remove the magnetic lock accessory and

save the two removed screws for later use.

Step 4: Secure the two magnetic locks to the

magnetic lock fasteners using screws.

Step 5: Secure the assembled magnetic locks to the

guide rail.

步骤1：将导轨紧固在门框。

步骤2：将立柱与天窗连接板固定。

步骤3：拆除止摆器前滚轮。

步骤4：将立柱底部与机柜紧固。

拆除立柱侧面维护板后，将立柱和门楣平放在地面组装。

组装完成后，确保立柱与门楣各面对齐。

安装前，先拆除门楣后盖板，待所有器件安装完成后

再装回。

安装前，请拆除玻璃门

运输保护胶条。

确保玻璃门之间无缝隙，且平整。

确保玻璃门与立柱之间没有摩擦。

确保缓冲器完成到位。

步骤1：组装机柜等宽的前后封板。

Step 1: Assemble front and rear sealing plates

that are as wide as the cabinet. Step 1: Secure the guide rail

to the door frame.

步骤2：将前后封板固定在机柜上。

步骤3：使侧封板带凹口侧朝上，将侧封板卡入前

后封板。

从门盒物料中取出1100mm或者1200mm

机柜侧封板，根据实际情况拼接600mm宽

或者800mm宽机柜下封板。

Step 2:

Secure the front and rear sealing

plates to the cabinet.

Step 3:

Place the side with dents upwards,

and snap the side sealing plate into

the front and rear sealing plates.

Take the side sealing plate for the

1100 mm or 1200 mm deep cabinet

out of the door box materials, and

splice the bottom sealing plate for the

600 mm or 800 mm wide cabinet

based on the site requirements.

Before installation, ensure that the left and right

end cabinets are on the same horizontal line.

Ensure that there is no gap between the

glass doors and they are ﬂush.

Ensure that there is no friction between

the glass doors and posts.

Ensure that the buers are installed

properly.

Before installation, remove the rear cover of the door

head and reinstall it after all components are installed.

600mm宽机柜拼接孔位

Splicing holes for a 600 mm

wide cabinet

Splicing holes for a

800 mm wide cabinet

800mm宽机柜拼接孔位

列头柜

End cabinet

Step 1: Push the door onto the guide rail.

Step 2: Set the spring of the middle buer to the

compressed state.

Step 3: Push an end buer into each end of the

guide rail according to the direction of the

arrow on the label.

Step 1: Secure the internal posts to the internal door head. Step 2: Secure the posts to the skylight connective plate.

Step 3: Remove the front wheel of the damper.

Step 4: Secure the bottom of the posts to the cabinets.

After removing the maintenance panels

from both sides of the posts, put the posts

and door head horizontally on the ﬂoor

and assemble them. After the assembly is

complete, verify that the posts are ﬂush with

the door head.

智能微模块推拉门快速指南 (高配，21501718，21501712)

Smart Module Sliding Door Quick Guide (Advanced Conﬁguration, 21501718, 21501712)

Step 1: Install the door rubber strips.

Before installation, remove

the protective rubber strips

from the glass door.

确保门与胶条紧密贴合、

无缝隙。

确保内外侧胶条与门上方

平齐，底部胶条与门同宽。

Ensure that the door is in

close contact with the rubber

strips without gaps.

Ensure that the inner and

outer rubber strips are ﬂush

with the door and the rubber

strip at the bottom is as wide

as the door.

3 N·m

M5x10

3 N·m

M6x16

3 N·m

M6x16

1:有滚轮机柜固定孔位

2:无滚轮机柜固定孔位

1: Securing holes for cabinets with castors

2: Securing holes for cabinets without castors

立柱

Post

门楣

Door head

天窗连接板 Skylight connective plate

端部缓冲器

End buer

电磁吸铁

固定角件

Magnet

fastener

电磁锁附件

Magnetic lock

accessory

电磁锁固定件

Magnetic lock

fastener

电磁吸铁

Magnet

垫片

Washer

3 N·m

M6x16

安装前确保左右列头柜在同一个水平线上。

3 N·m

M5x10

中间缓冲器

Middle buer

步骤1：装回止摆器前滚轮。

Step 1: Reinstall the front wheel of the damper.

说明

说明说明

说明

NOTE

（可选）调节电磁锁间隙

(Optional) Adjusting the Magnetic Lock Gap

05 07 安装外门框

Installing an External Door Frame

06 安装外门框和门盒

Installing an External Door Frame and Door Boxes

08 （可选）安装PAD安装件和门禁机

(Optional) Installing a PAD Mounting Kit and Access Control Device

安装立柱侧盖板

Installing Side Covers for the Posts

安装门盒挂装件

Installing Door Box Hanging Kits

Step 1: Install the bottom plate of the PAD mounting kit.

Step 2: Pre-route the cables for the PAD and access control device.

Step 3: Remove the bae plate from the installation position and

secure the bae plate with the cable hole in the lower part. Step 8: Install the access control device.

a: Remove the screws (set aside) from the access control device and take o the baseplate.

b: Secure the baseplate to the bae plate.

c: Route the cable of the access control device through the cable hole in the bae plate.

d: Secure the access control device to the baseplate.

Step 6: Install the PAD cover and pull the pre-routed cables out of the

cable hole.

Step 7: Adjust the feet on the PAD

mounting support and clamp the

PAD into the PAD mounting support.

步骤1：将门框扶起，并与机柜内门框顶部固定。

步骤2：紧固立柱底部螺丝。

步骤3：安装门盒。

Step 1: Stand up the door frame, and secure it to the top of

the internal door frame of the cabinet.

Step 2: Tighten the screws at the bottom of the posts.

Step 3: Install door boxes.

步骤1：安装立柱侧板盖板。

Step 1: Install side covers for the posts.

步骤1：面向通道，将标识“L”、“R”的门盒挂装件

分别紧固在机柜顶部。

步骤2：将预装在立柱的线缆拉出。

步骤3：将门盒挂装件紧固在立柱上。

1100mm机柜场景时，门盒使用单独发货的

1100mm门盒，门物料中打包的1200mm门

盒舍弃。

步骤1：将外立柱与外门楣固定。

Step 1: Secure the external posts to the external

door head.

将立柱和门楣平放在地面组装。

组装完成后，确保立柱与门楣各面对齐。

安装门盒前，请确认是否需要安装eLight。如果安装eLight，建议先安

装eLight后再执行此步骤。

In case of 1100 mm cabinet scenario, the

1100 mm door box separately delivered is used,

the 1200 mm door box packaged in the door

materials is abandoned.

Step 1: Facing the aisle, secure the door box hanging

kits labeled L and R to the top of the cabinet.

Step 2: Pull out the cables that are preinstalled in

the post.

Step 3: Secure the door box hanging kits to the post.

Put the posts and door head horizontally on

the ﬂoor and assemble them.

After the assembly is complete, verify that

the posts are ﬂush with the door head.

Before installing the door boxes, check whether the eLight needs

to be installed. If the eLight needs to be installed, you are advised

to install the eLight ﬁrst and then perform this step.

智能微模块推拉门快速指南 (高配，21501718，21501712)

Smart Module Sliding Door Quick Guide (Advanced Conﬁguration, 21501718, 21501712)

步骤1：安装PAD安装件底板。

步骤2：预布PAD和门禁机线缆。

步骤3：拆除安装位挡片，并固定过线孔下端的挡片。

外门楣（背面）

External door

head (rear)

外立柱

External door frame

3 N·m

M5x10

调节电磁锁间隙

Adjusting the Magnetic Lock Gap

If the magnetic lock fails to attract the magnet after being installed on a sliding door,

you can adjust the magnetic lock by either of the following methods:

Loosen the two M6 screws on the ﬁxing

corner pieces of the magnet. Then move the

ﬁxing corner piece assembly horizontally until

the magnet closely attaches to the magnetic

lock.

推拉门电磁锁安装完毕后如若出现电磁锁吸合不上的情况时，可采取如下两种方案

对电磁锁进行调节：

拧松用于电磁吸铁固定角件的两颗M6的螺钉，

横向移动电磁吸铁固定角件组合体，至电磁

吸铁与电磁锁紧密贴合为止。

方案一：方案二：

Method 1: Method 2:

Loosen the two screws that secure the

magnetic lock. Then insert a washer between

the magnetic lock and the sheet metal

fastener until the magnet closely attaches to

the magnetic lock.

拧松固定电磁锁的两颗螺钉，在电磁锁与电磁

锁固定钣金件之间插入垫片，至电磁吸铁与电

磁锁紧密贴合为止。

3 N·m

M5x10

3 N·m

M5x10

Skylight

connective

plate

天窗连接板

机柜顶部

Top of the

cabinet

预装线缆

Preinstalled cables

3 N·m

M5x10

1 N·m

3 N·m

M5x10

步骤5：拆除安装位挡片，并固定PAD支架。

Step5: Remove the bae plate from the installation position and

secure the PAD mounting bracket.

步骤4：（可选）如果PAD安装支架下方支脚与PAD不等宽，调节支脚。

Step 4: (Optional) If the feet in the lower part of the PAD mounting

bracket are not as wide as the PAD, adjust the feet.

3 N·m

M5x10

步骤6：安装PAD盖板，并从过线孔拉出预布的线缆。

步骤7：调整PAD安装支架上方支脚，

将PAD卡入PAD安装支架。

步骤8：安装门禁机。

a：拆下门禁机固定螺钉（请妥善保存），取下底板。

b：将底板固定在挡片上。

c：将门禁机线缆穿过挡片过线孔。

d：将门禁机固定在底板上。

说明说明

说明

NOTE

Huawei 21501718 User guide

Brand: Huawei

Model: 21501718

Type: User guide

Download PDF

report

in other languages

日本語: Huawei 21501718 ユーザーガイド

Huawei 21501718 User guide

Huawei 21501718 User guide

in other languages

Related papers

Other documents