Tyan YR190-B7018 User manual

http://www.tyan.com

1

YR190-B7018

Service Engineer’s Manual

2

http://www.tyan.com

3

PREFACE

Copyright

This publication, including all photographs, illustrations, and software, is

Neither this manual, nor any material contained herein, may be reproduced

without written consent of manufacturer.

TYAN

®

is a registered trademark of MiTAC International Corporation.

Version 1.1

Disclaimer

Information contained in this document is furnished by MiTAC International

Corporation and has been reviewed for accuracy and reliability prior to

printing. MiTAC assumes no liability whatsoever, and disclaims any

express or implied warranty, relating to sale and/or use of TYAN

®

products

including liability or warranties relating to fitness for a particular purpose or

merchantability. MiTAC retains the right to make changes to produce

descriptions and/or specifications at any time, without notice. In no event

will MiTAC be held liable for any direct or indirect, incidental or

consequential damage, loss of use, loss of data or other malady resulting

from errors or inaccuracies of information contained in this document.

Trademark Recognition

All registered and unregistered trademarks and company names

contained in this manual are property of their respective owners including,

but not limited to the following.

TYAN

®

is a trademark of MiTAC International Corporation.

Intel

®

is a trademark of Intel

®

Corporation.

AMI

®

, AMIBIOS

®

and combinations thereof are trademarks of AMI

Technologies.

Microsoft

®

, Windows

®

are trademarks of Microsoft Corporation.

IBM

®

, PC

®

, AT

®

and PS/2

®

are trademarks of IBM Corporation.

Winbond

®

is a trademark of Winbond Electronics Corporation.

http://www.tyan.com

4

Federal Communication Commission (FCC)

Notice for the USA

Compliance Information Statement (Declaration of

Conformity Procedure) DoC FCC Part 15: This

device complies with part 15 of the FCC Rules

Operation is subject to the following conditions:

1) This device may not cause harmful interference;

2) This device must accept any interference received including

interference that may cause undesired operation. If this equipment

does cause harmful interference to radio or television reception,

which can be determined by turning the equipment off and on, the

user is encouraged to try one or more of the following measures:

– Reorient or relocate the receiving antenna.

– Increase the separation between the equipment and the receiver.

– Plug the equipment into an outlet on a circuit different from that of

the receiver.

Consult the dealer on an experienced radio/television technician for

help.

Notice for Canada

This apparatus complies with the Class A limits for radio interference as

specified in the Canadian Department of Communications Radio

Interference Regulations. (Cet appareil est conforme aux norms de

Classe A d’interference radio tel que specifie par le Ministere Canadien

des Communications dans les reglements d’ineteference radio.)

Notice for Europe (CE Mark)

This product is in conformity with the Council

Directive 89/336/EEC, 92/31/EEC (EMC).

CAUTION: Lithium battery included with this board. Do not puncture,

mutilate, or dispose of battery in fire. There will be danger of explosion if

battery is incorrectly replaced. Replace only with the same or equivalent

type recommended by manufacturer. Dispose of used battery according

to manufacturer instructions and in accordance with your local

regulations.

http://www.tyan.com

5

About this Manual

This manual provides you with instructions on installing your TYAN

YR190-B7018. This Manual is intended for experienced users and

integrators with hardware knowledge of personal computers.

This manual consists of the following parts:

Chapter1:

Provides an introduction to the TYAN YR190-B7018

barebones, standard parts list, describes the external

components, gives a table of key components, and

provides block diagram of the system.

Chapter2:

Covers procedures on installing the CPU, memory

modules and hard drives.

Chapter3:

Covers removal and replacement procedures for

pre-installed components.

Appendix:

List the cable connection and FRU part tables for

reference of system setup, and technical support

in

case a problem arises with your system.

http://www.tyan.com

6

SAFETY INFORMATION

Before installing and using TYAN YR190-B7018, take note of the

following precautions:

·Read all instructions carefully.

·Do not place the unit on an unstable surface, cart, or stand.

·Do not block the slots and opening on the unit, which are provided for

ventilation.

·Only use the power source indicated on the marking label. If you are not

sure, contact the power company.

·The unit uses a three-wire ground cable, which is equipped with a third

pin to ground the unit and prevent electric shock. Do not defeat the

purpose of this pin. If you outlet does not support this kind of plug,

contact your electrician to replace your obsolete outlet.

·Do not place anything on the power cord. Place the power cord where it

will not be in the way of foot traffic.

·Follow all warnings and cautions in this manual and on the unit case.

·Do not push objects in the ventilation slots as they may touch high

voltage components and result in shock and damage to the

components.

·When replacing parts, ensure that you use parts specified by the

manufacturer.

·When service or repairs have been done, perform routine safety checks

to verify that the system is operating correctly.

·Avoid using the system near water, in direct sunlight, or near a heating

device.

·Cover the unit when not in use.

http://www.tyan.com

7

Table of Contents

Chapter 1: Overview.........................................................................9

1.1 About the TYAN YR190-B7018 ................................................ 9

1.2 Features.................................................................................. 10

1.3 Product Model......................................................................... 12

1.4 Standard Parts List ................................................................. 13

1.4.1 Box Contents Per Node................................................... 13

1.4.2 Accessories ..................................................................... 14

1.5 About the Product................................................................... 16

1.5.1 System Front View (Per Node)........................................ 16

1.5.2 System Rear View (Per Node) ........................................ 18

1.5.3 Internal View (Per Node) ................................................. 19

Chapter 2: Setting Up.....................................................................21

2.0.1 Before you Begin ............................................................. 21

2.0.2 Work Area........................................................................ 21

2.0.3 Tools ................................................................................ 21

2.0.4 Precautions...................................................................... 22

2.1 Installing Motherboard Components....................................... 23

2.1.1 Installing Hard Drives....................................................... 23

2.1.2 Installing the CPU and Heatsink...................................... 27

2.1.3 Installing the Memory....................................................... 30

2.2 Rack Mounting........................................................................ 33

2.2.1 Installing the Server in a Rack......................................... 33

2.2.2 Installing the inner Rails to the Chassis........................... 34

2.2.3 Installing the Outer Rails to the Rack .............................. 35

2.2.4 Rack mounting the Server ............................................... 36

Chapter 3: Replacing Pre-Installed Components ........................39

3.1 Introduction ............................................................................. 39

3.2 Disassembly Flowchart........................................................... 39

3.3 Replacing Motherboard Components..................................... 41

3.3.1 Replacing Expansion Card .............................................. 41

3.3.2 Disconnecting All Motherboard Cables ........................... 43

3.3.3 Removing the Motherboard ............................................. 44

3.4 Replacing the Power Distribution Board ............................... 45

3.5 Replacing the Front Panel Board.......................................... 46

3.5.1 Front Panel Board Features ............................................ 48

3.5.2 Front Panel Board Connector Pin Definition ................... 48

3.6 Replacing the System Fan.................................................... 49

3.7 Replacing the SATA Backplane Board................................. 52

http://www.tyan.com

8

3.7.1 SATA Backplane Board Features.................................... 54

3.7.2 SATA Backplane Board Connector Pin Definitions ......... 55

3.8 Replacing the Power Supply................................................. 57

Appendix I: Cable Connection Tables .......................................... 59

Appendix II: FRU Parts Table ........................................................ 61

Appendix III: Technical Support.................................................... 63

9

http://www.tyan.com

Chapter 1: Overview

1.1 About the TYAN YR190-B7018

Congratulations on your purchase of the TYAN

®

YR190-B7018, a highly

optimized rack-mountable barebone system. The YR190-B7018 is

designed to support two Intel

®

Xeon 5500/5600 processors and up to 96

GB DDR3-800/1066/1333 memory per node, providing a rich feature set

and incredible performance. Leveraging advanced technology from Intel

®

,

YR190-B7018 server system is capable of offering scalable 32 and 64-bit

computing, high bandwidth memory design, and lightning-fast PCI-E bus

implementation. The YR190-B7018 not only empowers your company in

nowadays IT demand but also offers a smooth path for future application

usage.

TYAN

®

is also proud to deliver the YR190-B7018 in flavor while

supporting up to eight hot-swap hard drives (four per node). The

YR190-B7018 uses TYAN

®

’s latest chassis featuring a robust structure

and a solid mechanical enclosure. All of this provides YR190-B7018 the

power and flexibility to meet the needs of nowadays server application.

10

http://www.tyan.com

1.2 Features

TYAN YR190B7018 (B7018Y190X2-045V4H)

Form Factor 1U Rackmount Frame w/ 2x 1U Blades

Chassis Model YR190

Dimension (D x W x

H)

28.74" x 17.32" x 1.72" (730 x 440 x 43.6mm)

Blade Dimension

(D x W x H)

28.74" x 8.46" x 1.61" (730 x 214.8 x 40.8mm)

Motherboard S7018GM3NR

Board Dimension 6.3"x16.4" (160x416.6mm), per blade

Gross Weight 18 kg

System

Feature Two nodes in one chassis

Buttons (1) RST / (1) PWR / (1) ID

LEDs (1) PWR / (1) BMC / (2) LAN / (1) HDD

Front Panel (per

blade)

I/O Ports (2) USB ports

Type / Q'ty 2.5" Hot-Swap / (4)

External Drive

Bay (per blade)

Supported HDD

Interface

SATA-II 3.0Gb/s

System Cooling

Configuration

(per blade)

FAN (3) 4cm fans

Type ERP1U cold-swap

Input Range Full-range AC(100-240V)

Frequency 47 - 63 Hertz

Output Watts 450 Watts

Power Supply

(per blade)

Efficiency PFC / 80-plus Silver

Supported CPU

Series

Intel Xeon Processor 5500/5600 Series

Socket Type / Q'ty LGA1366 / (2)

Thermal Design

Power (TDP)

wattage

Max up to 95W

System Bus

Up to 4.8/ 5.86/ 6.4GT/s with Intel QuickPath

Interconnect (QPI) support

Processor (per

blade)

CPU list Coming soon

Chipset (per

blade)

MCH / ICH Intel 5500 / ICH10R

Supported DIMM

Qty

(6)+(6) DIMM slots

Memory (per

blade)

DIMM Type / Speed

DDR3 800/1066/1333* RDIMM/UDIMM / * limit 1

per channel for 1333MHz speed

http://www.tyan.com

11

Capacity Up to 96GB RDIMM / 48GB UDIMM

Memory channel 3 Channels per CPU

Memory voltage 1.5V

PCI-E (1) PCI-E Low-Profile Gen.2 x16 slot

Expansion Slots

(per blade)

Pre-install TYAN

Riser Card

M7018-R16-1L, 1U PCI-E x16 riser card (right)

Port Q'ty Total (3) ports, (1) dedicated for IPMI

LAN (per blade)

Controller Intel 82576EB / Intel 82574L

Connector (4) SATA

Controller Intel ICH10R

Speed 3.0 Gb/s

Storage (per

blade)

SATA

RAID RAID 0/1/10/5 (Intel Matrix RAID)

Connector type D-Sub 15-pin

Resolution 1600x1200@60Hz

Graphic (per

blade)

Chipset Aspeed AST2050

USB (5) ports (2 at front, 2 at rear, 1 Type A onboard)

COM (1) DB-9 COM port

VGA (1) D-Sub 15-pin port

I/O ports (per

blade)

RJ-45 Total (3) ports, (1) dedicated for IPMI

Chipset Winbond W83793G

Temperature

Monitors temperature for CPU & system

environment

LED

Fan fail LED indicator / Over temperature

warning indicator

System

Monitoring (per

blade)

Others

Chassis intrusion detection / Watchdog timer

support

Onboard Chipset Onboard Aspeed AST2050

AST2050 IPMI

Feature

IPMI 2.0 compliant baseboard management

controller (BMC) / USB 2.0 virtual hub / BIOS

update

Server

Management (per

blade)

AST2050 iKVM

Feature

24-bit high quality video compression / Dual

10/100 Mb/s MAC interfaces

Brand / ROM size AMI / 4MB

BIOS (per blade)

Feature

Multiple boot options / Plug and Play (PnP)

/PCI2.3 /WfM2.0 /SMBIOS2.3 /PXE boot / ACPI

2.0 power management /Power on mode after

power recovery / User-configurable H/W

monitoring / Auto-configurable of hard disk types

Operating

System

OS supported list Please visit our Web site for the latest update.

FCC (DoC) Class A

Regulation

CE (DoC) Yes

http://www.tyan.com

12

Operating Temp. 10° C ~ 35° C (50° F~ 95° F)

Non-operating

Temp.

- 40° C ~ 70° C (-40° F ~ 158° F)

Operating

Environment

In/Non-operating

Humidity

90%, non-condensing at 35° C

RoHS

RoHS 6/6

Complaint

Yes

Barebone (1) YR190-B7018 Barebone

Manual

(1) Quick Ref. Guide / (1) MB User's manual +

(1) BB User's manual

Installation CD (1) TYAN installation CD

Rail kit (1) Sliding rail kit for YR190

Package

Contains

Accessories (4) Heatsinks / (4) Power Cords

1.3 Product Model

Model HDD Bays Power supply

YR190-B7018

(two nodes)

Hot-swap, 8 HDDs (2) 450W

13

http://www.tyan.com

1.4 Standard Parts List

This section describes the YR190-B7018 package contents and

accessories. Open the box carefully and ensure that all components are

present and undamaged. The product should arrive packaged as

illustrated below.

1.4.1 Box Contents Per Node

Component Description

1U chassis, 2 nodes

(4) hot swap HDD bays per node

TYAN

®

S7018 system board

(pre-installed)

450W single Power Supply

(pre-installed)

(1) 40x28mm System Fan

(pre-installed)

(2) 40x56mm System Fans

(pre-installed)

Power Distribution Board

(pre-installed)

SATA HDD Backplane Board

(pre-installed)

M7018-R16-1L PCI-E Riser Card

(pre-installed)

Front Panel Board

(pre-installed)

14

http://www.tyan.com

1.4.2 Accessories

If any items are missing or appear damaged, contact your retailer or

browse to TYAN

®

’s website for service: http://www.tyan.com

The web site also provides information of other TYAN

®

products, as

well as FAQs, compatibility lists, BIOS settings, etc.

1 x TYAN

®

Motherboard Drive

CD

4 Heatsinks

HDD Screws

Power Cables

(Left to right: Europe, US)

2 Europe + 2 US

Barebone Manual Mainboard Manual

15

http://www.tyan.com

Rail Kit

Rail x 2 Screw Pack

16

http://www.tyan.com

1.5 About the Product

The following views show you the product.

1.5.1 System Front View (Per Node)

HDD LED Description

Activity LED: Off

Fault LED: Off

Drive present, no activity

Activity LED: blinking green

Fault LED: Off

Drive present, with activity

Activity LED: Off

Fault LED: Red

HDD Fail

Activity LED: random

Fault LED: blinking red @ 4 Hz

Identify

Activity LED: random

Fault LED: blinking red @ 1 Hz

Rebuild

17

http://www.tyan.com

Front Panel LED Description

1. HDD

Green: Ready

Blinking Green: Activity

Red: TBD

2. LAN2

Green: Link

Blinking Green: Activity

3. LAN1

Green: Link

Blinking Green: Activity

4. IPMI

Green: Normal Status

Amber: System Failed

Without IPMI module:

FAN failed

system thermal problem

With IPMI module:

IPMI fault alert event is raised.

5. Power

Green: Power ON

Blue: ID LED

Front Panel Button Description

6. Power On/ Off Power up and power down the system (Use a pin)

7. ID (UID)

Press once and the blue ID LED on the rear panel

will light up. The Power LED on the front panel

will turn blue.

8. Reset Press to reset the system

18

http://www.tyan.com

1.5.2 System Rear View (Per Node)

blue ID LED: When the ID LED button on the rear panel is pressed,

the blue Power LED on the front panel and the blue ID LED on

the rear panel will light up. The technical personnel can easily

locate the system on the rack, disconnect cables from the

system, and remove it from the rack for later repair.

LAN LED: The three onboard Ethernet ports have green and

amber LEDs to indicate LAN status. The table below illustrates

the different LED states.

Ethernet LAN Link/Activity LED Description

Left: slow blinking green

Right: Off

10 Mbps Link

Left: blinking green

Right: Off

10 Mbps Activity

Left: slow blinking green

Right: green

100 Mbps Link

Left: blinking green

Right: green

100 Mbps Activity

Left: slow blinking green

Right: amber

1000 Mbps Link

Left: blinking green

Right: amber

1000 Mbps Activity

Left: Off

Right: Off

No Link

19

http://www.tyan.com

1.5.3 Internal View (Per Node)

Number Description

1 HDD Cage

2 SATA HDD Backplane Board

3 System Fans

4 Power Distribution Board

5 Memory Slots

6 CPU Sockets

7 PCI-E Riser Card Assembly

20

http://www.tyan.com

NOTE

Page is loading ...

Tyan YR190-B7018 User manual

Tyan YR190-B7018 User manual

Related papers

Other documents