IRG6 INFRARED REPEATING SYSTEM
Installation is easy as all connections are made via plug-in jacks. The IRG6 receiver module may be located where the
cable, satellite box and any other equipment is located. Connect a coax cable from the source equipment to the front connector
(next to the emitter jack) on the IRG6 receiver. Connect the coax cable that runs to the TV location to the rear jack. Plug the
IRBug emitter into the emitter jack and attach it over the sensor of the device to be controlled. The IRG6 transmit module is
usually located near the TV. Connect a coax cable from the TV's cable input to the IRG6 transmitter's front connector (next to the
red LED). Connect the coax coming from the IRG6 receiver to the rear jack. Plug the Stealth eye (the larger plug-in piece) and the
12 volt power supply into the jacks on the front of the IRG6 transmitter. The Stealth eye should be mounted near the TV where it
can "see" your remote control. Due to it's small size it can easily be concealed.
Test the system by sending commands for the device being controlled to the Stealth eye. The device should respond as
though it is being dircetly controlled. If a problem occurs, check the red talk-back light on the transmit module. It should flash
only when signals are being sent. If there is no talk-back light, check the power supply. If the TV is not getting a signal, check the
coax cable and connections. If the talk-back light is stuck on or twinkling, try moving the Stealth eye away from the source of
interference. If the controlled equipment does not work properly, try relocating the IRBug emitter to a different position.
The IRG6 system is an infrared repeating system that allows use of existing coax cable to transmit remote control signals
from the TV to equipment in another location. The IRG6 consists of two units. The transmitter uses dual-band Stealth technology
to intercept signals from the remote control and transmit them over standard coax cable (such as RG-6 or RG-59). It has jacks for
cable input and output, power and an infrared eye. The receiver connects the coax to one or more emitters allowing the
components to be controlled from the transmitter's location. This unit has jacks for cable input and output and an emitter output.
Both transmitter and receiver are available in a compact die cast housing or on a Decora wall plate.
NOTE: Never plug an emitter into the sensor eye jack on the transmit module and vice versa.
The coax running between the IRG6 transmit and receive modules should be a direct run with no splitters,
switchers or other devices.
Multiple emitters can be connected to the IRG6 receiver by using the Audioplex IRS-1 or by using a connector
block. (To attach to a connecting block, use a cable with a 1/8" plug on one end and stripped leads on the other.
The tip connection goes to the signal terminal, and the sleeve connection to ground. On most connector blocks,
the Power connection is not needed.
Be sure that the Stealth eye can't "see" any of the emitters. This might create a loop that could cause erratic
operation or lockup. This shouldn't be an issue if the emitters are in another room or behind closed doors.
Your AUDIOPLEX TECHNOLOGY IRG6 Infrared Repeating System is covered by a LIFETIME warranty against any
defects in workmanship and materials. Any defects will be remedied without charge for labor or parts.
Damage incurred by shipping or by accident is not considered to be a defect, and is not covered by this warranty.
AUDIOPLEX TECHNOLOGY is not responsible for defective operation caused by abuse or by modification or service by
unauthorized person or agency.
The unit must be properly installed and operated according to instructions for the warranty to apply. Any necessary
servicing must be done by AUDIOPLEX TECHNOLOGY. The product must be returned expenses prepaid, with written
authorization from the company. The product must be shipped with proof of purchase and in the original carton and packing
material to avoid damage. This warranty gives you specific legal rights. You may have other rights which vary from state to state.
INSTALLATION
WARRANTY
TECHNOLOGY
INSTALLATION MANUAL
2006 - 4/10/06
TRANSMITTER PLATE
RECEIVER PLATE
IRG6 RECEIVER PLATE
IR CONNECTING BLOCK
TYPICAL IRG6 APPLICATION
ADVANCED IRG6 APPLICATION (controlling multiple components)
404 GWH PO BOX 440 MELVIN VILLAGE NH 03850 800-257-2077 E-MAIL: [email protected]
2006 - 4/10/06
AUDIOPLEX TECHNOLOGY
WIRING DIAGRAM
L
E
B
M
O
S
R
?
P
N
?
E
S
E
N
D
O
I
H
T
E
S
L
E
P
U
?
Q
CALL
TOLL-FREE
1-800-257-2077
Stealth eye
Coax
Coax
Coax
1/8" plug to stripped leads
(Tip=Signal or IR IN)
Coax to
IRG6 Transmitter
A/V
INPUTS
CABLE / SATELLITE BOX
IRBug
Coax
Coax from cable / dish
CABLE / SATELLITE BOX
EMITTERS
+12V
12VDC
GND
STATUS
EMITTERS
IR IN
TECHNOLOGY
IRB-4
DVD
disc 5 2.53
VCR
32.53
RECEIVER
DVD DOLBY DIGITAL
OUT
IN
FROM
CABLE / DISH
-
1
-
2
Ask a question and I''ll find the answer in the document
Finding information in a document is now easier with AI
Related papers
-
Audioplex RC-5 Installation guide
-
Audioplex STEALTH IR HW Installation guide
-
-
-
-
-
-
-
-
Other documents
-
Wyrestorm EXP-EX-COAX-50 User manual
-
-
Channel Plus SVS-88 User manual
-
Williams Sound SoundPlus™ 2 and 4 channel Infrared Listening Systems User manual
-
-
-
-
-
-
Xantech 17294 Rp User manual