Astonica 50105573 User manual

Brand: Astonica

Model: 50105573

Type: User manual

Astonica 50105573 is a 48" Cast Aluminum Table. It is intended for residential, non-commercial use. The table is made of durable materials and is easy to assemble. It has adjustable feet for leveling on uneven surfaces. The table is perfect for both indoor and outdoor use. It is easy to clean and maintain. With its stylish design, this table will complement any décor.

Model No. 50105573

Springhill 48"

Cast Aluminum Table

Instruction Manual

IF YOU HAVE ANY PROBLEMS OR QUESTIONS CONCERNING THIS PRODUCT,

DO NOT RETURN IT TO YOUR RETAILER, CONTACT CUSTOMER SERVICE AT

1-888-424-3354

Made in China

Distributed by:

World Factory, Inc.

Coppell TX 75019

Read the instructions and precautions before use of this product

Please keep this instruction manual for future reference

IF YOU HAVE ANY PROBLEMS OR QUESTIONS CONCERNING THIS PRODUCT,

DO NOT RETURN IT TO YOUR RETAILER, CONTACT CONSUMER SUPPORT AT

1-888-424-3354

IF YOU ARE A STORE MANAGER OR EMPLOYEE IN NEED OF ASSISTANCE CALL

1-888-851-5569

PLEASE HAVE YOUR STORE NUMBER READY

Limited Warranty

World Factory, Inc.

Products for Home Use

World Factory, Inc.

(Seller) warrants to the original Buyer only, that each Astonica

Product will be

free from defects in material and workmanship for a period of one (1) year from date of purchase.

SELLER’S SOLE OBLIGATION AND BUYER’S EXCLUSIVE REMEDY UNDER THIS LIMITED

WARRANTY SHALL BE THE REPAIR OR REPLACEMENT OF PARTS, WITHOUT CHARGE, WHICH

ARE DEFECTIVE IN MATERIAL OR WORKMANSHIP. ANY PARTS AS DETERMINED BY THE

SELLER WHICH HAVE BEEN MISUSED; ABUSED OR DAMAGED EITHER DIRECTLY OR INDIRECTLY

FROM REPAIRS OR ALTERATIONS ATTEMPTED BY UNAUTHORIZED PERSONS; IMPROPER

MAINTENANCE, NEGLECT OR ACCIDENT ARE NOT COVERED BY THIS LIMITED WARRANTY. This

warranty does not apply to damage, heat-induced coloration changes, scratching or alteration due to

normal use or weathering. To make a claim under this Limited Warranty, you must return the complete

product with proof of purchase, transportation prepaid, to any World Factory, Inc.

authorized service

center. Call 1-888-424-3354 for the location of the nearest authorized service center.

Additional Limitations

THIS LIMITED WARRANTY DOES NOT APPLY TO ACCESSORY OR CONSUMABLE ITEMS RELATED

TO THIS PRODUCT. ALL IMPLIED WARRANTIES SHALL BE LIMITED IN DURATION TO ONE (1)

YEAR FROM DATE OF PURCHASE. IN NO EVENT SHALL SELLER BE LIABLE FOR ANY

INCIDENTAL OR CONSEQUENTIAL DAMAGES, INCLUDING BUT NOT LIMITED TO LIABILITY FOR

LOSS OF PROFITS, ARISING FROM THE SALE OR USE OF THIS PRODUCT.

If any provision of this Limited Warranty is for any reason held to be invalid or unenforceable, such

provision shall not affect any other provision herein, this Limited Warranty shall be construed as if

such invalid and/or unenforceable provision had never been contained herein.

This Warranty contains the entire agreement between Seller and Buyer and supersedes any and all

prior agreements, arrangements, or understandings between the parties relating to product warranty.

270905rev1

Due to ongoing product development

the actual product or products may vary from

the illustrations or photos shown within this manual.

NOTE: This product is intended for residential, non-commercial use.

PARTS LIST

PART # DESCRIPTION QUANTITY

IF YOU HAVE ANY PROBLEMS OR QUESTIONS CONCERNING THIS PRODUCT,

DO NOT RETURN IT TO YOUR RETAILER. CONTACT CUSTOMER SERVICE AT

1-888-424-3354

Carefully remove the contents from the package. If any parts are missing do not

attempt to use the product until they have been obtained and correctly installed.

ASSEMBLY INSTRUCTIONS

NOTE: This product is intended for residential, non-commercial use.

Figure 1

 CAUTION: Do not over tighten fasteners.

1. (SEE FIGURE 1) Place table top (A) upside down on flat non-scratch surface.

2. Install threaded studs (E) into table top (A).

3. Turn one table leg (B) upside down and align leg over threaded stud (E).

4. Place flat washer (G) and lock washer (H) onto threaded stud. Attach leg using hex nut (F).

 Repeat steps 3 and 4 for remaining table legs. Do not tighten hardware.

5. Install threaded studs (E) into each table leg (B).

6. Align connecting ring (C) between table legs (B) and place connecting ring over threaded studs.

7. Place flat washer (G) and lock washer (H) over each threaded stud, secure using hex nut (F).

 Do not tighten hardware.

8. With each leg attached to the connecting ring tighten each hex nut a few revolutions at a time,

 alternating between hex nuts in a cross corner "X" fashion.

 NOTE: Tightening every other hex nut in a cross fashion will ensure your table is level by

 placing equal pressure on each joint.

9. Install adjustable feet (D) at bottom of each table leg (B). Turn table upright.

10.Adjust table legs as needed using the adjustable feet at bottom of each leg. Turn feet by

 hand until table is level to the floor.

 Your table is now ready to use.

A Table Top 1

B Table Leg 4

C Connecting Ring 1

D Adjustable Feet 4

E Threaded Stud, 8mm 16

F Hex Nut, 8mm 16

G Flat Washer, 8mm 16

H Lock Washer 16

Astonica 50105573 User manual

Astonica 50105573 User manual

Astonica 50105573 User manual

Related papers

Other documents