HP 1GSa/s User manual

SERVICE MANUAL

HP 16532A

1 GSa/s Digitizing

Oscilloscope

 COPYRIGHT HEWLETT-PACKARD COMPANY,

COLORADO SPRINGS DIVISION 1991-1993

1900 GARDEN OF THE GODS ROAD, COLORADO SPRINGS, COLORADO U.S.A.

Manual Part No. 16532-97002 PRINTED: JULY 1993

GENERAL - This is a Safety Class I instrument (provided with

terminal for protective earthing).

OPERATION - BEFORE APPLYING POWER verify that the

power transformer primary is matched to the available line

voltage, the correct fuse is installed, and Safety Precautions

are taken (see the following warnings). In addition, note the in-

strument’s external markings which are described under

"Safety Symbols."

• Servicing instructions are for use by service-trained per-

sonnel. To avoid dangerous electric shock, do not perform

any servicing unless qualified to do so.

• BEFORE SWITCHING ON THE INSTRUMENT, the protec-

tive earth terminal of the instrument must be connected to

the protective conductor of the (mains) powercord. The

mains plug shall only be inserted in a socket outlet pro-

vided with a protective earth contact. The protective action

must not be negated by the use of an extension cord

(power cable) without a protective conductor (grounding).

Grounding one conductor of a two-conductor outlet is not

sufficient protection.

• If this instrument is to be energized via an auto-trans-

former (for voltage reduction) make sure the common ter-

minal is connected to the earth terminal of the power

source.

• Any interruption of the protective (grounding) conductor

(inside or outside the instrument) or disconnecting the pro-

tective earth terminal will cause a potential shock hazard

that could result in personal injury.

• Whenever it is likely that the protection has been im-

paired, the instrument must be made inoperative and be

secured against any unintended operation.

• Only fuses with the required rated current, voltage, and

specified type (normal blow, time delay, etc.) should be

used. Do not use repaired fuses or short circuited fuse-

holders. To do so could cause a shock or fire hazard.

• Do not operate the instrument in the presence of flamma-

ble gasses or fumes. Operation of any electrical instru-

ment in such an environment constitutes a definite safety

hazard.

• Do not install substitute parts or perform any unauthorized

modification to the instrument.

• Adjustments described in the manual are performed with

power supplied to the instrument while protective covers

are removed. Energy available at many points may, if con-

tacted, result in personal injury.

• Any adjustment, maintenance, and repair of the opened in-

strument under voltage should be avoided as much as

possible, and when inevitable, should be carried out only

by a skilled person who is aware of the hazard involved.

• Capacitors inside the instrument may still be charged

even if the instrument has been disconnected from its

source of supply.

SAFETY SYMBOLS

Instruction manual symbol. The product will be

marked with this symbol when it is necessary for

the user to refer to the instruction manual in order

to protect against damage to the product.

Earth terminal (sometimes used in manual to in-

dicate circuit common connected to grounded

chassis).

The WARNING sign denotes a hazard. It

calls attention to a procedure, practice,

or the like, which, if not correctly per-

formed or adhered to, could result in personal injury. Do not

proceed beyond a WARNING sign until the indicated condi-

tions are fully understood and met.

The CAUTION sign denotes a hazard. It

calls attention to an operating procedure,

practice, or the like, which, if not cor-

rectly performed or adhered to, could result in damage to or

destruction of part or all of the product. Do not proceed be-

yond a CAUTION sign until the indicated conditions are fully

understood or met.

SAFETY CONSIDERATIONS

Indicates hazardous voltages

SC1D984

CONTENTS

SECTION I

General Information

1-1. Introduction .............................................................................................................................. 1-1

1-2. Module Covered by This Manual ............................................................................................ 1-1

1-3. Safety Requirements ............................................................................................................... 1-1

1-4. Product Description ................................................................................................................. 1-2

1-5. Accessories Supplied .............................................................................................................. 1-2

1-6. Accessories Available............................................................................................................... 1-2

1-7. Specifications ........................................................................................................................... 1-2

1-8. Operating Characteristics ....................................................................................................... 1-2

1-9. Recommended Test Equipment ............................................................................................. 1-2

SECTION II

Installation

2-1. Introduction ............................................................................................................................. 2-1

2-2. Initial Inspection ...................................................................................................................... 2-1

2-3. Preparation for Use ................................................................................................................ 2-1

2-4. Power Requirements .............................................................................................................. 2-1

2-5. Safety Requirements .............................................................................................................. 2-1

2-6. Module Installation ................................................................................................................. 2-1

2-7. Operating Environment .......................................................................................................... 2-4

2-8. Storage .................................................................................................................................... 2-4

2-9. Packaging ............................................................................................................................... 2-4

2-10. Tagging for Service ................................................................................................................ 2-4

SECTION III

Performance Tests

3-1. Introduction .............................................................................................................................. 3-1

3-2. Recommended Test Equipment ............................................................................................. 3-1

3-3. Test Record .............................................................................................................................. 3-1

3-4. Performance Test Interval ....................................................................................................... 3-1

3-5. Performance Test Procedures ................................................................................................ 3-1

3-6. DC CAL OUTPUT Test ............................................................................................................. 3-2

3-7. AC CAL OUTPUT Test ............................................................................................................. 3-3

3-8. Input Resistance ...................................................................................................................... 3-4

3-9. Voltage Measurement Accuracy ............................................................................................. 3-6

3-10. Offset Accuracy ....................................................................................................................... 3-9

3-11. Bandwidth ................................................................................................................................ 3-11

3-12. Time Measurement Accuracy .................................................................................................. 3-13

3-13. Trigger Sensitivity .................................................................................................................... 3-15

HP 16532A - Table of Contents

v

SECTION IV

Calibration

4-1. Introduction............................................................................................................................... 4-1

4-2. Safety Requirements................................................................................................................ 4-1

4-3. Calibration Interval.................................................................................................................... 4-1

4-4. Maintaining System Integrity.................................................................................................... 4-1

4-5. Calibration Protection Switch................................................................................................... 4-1

4-6. Recommended Test Equipment..............................................................................................4-2

4-7. Instrument Warmup.................................................................................................................. 4-2

4-8. Calibration................................................................................................................................. 4-2

4-9. Setting the PROTECT/UNPROTECT Switch to UNPROTECT................................................ 4-3

4-10. Equipment Required for Calibration ....................................................................................... 4-4

4-11. Loading the Default Calibration Factors................................................................................. 4-4

4-12. Self Cal Menu Calibrations...................................................................................................... 4-5

4-13. Setting the PROTECT/UNPROTECT Switch to PROTECT.................................................... 4-8

4-14. Sealing the Mainframe............................................................................................................. 4-8

Section V

Replaceable Parts

5-1. Introduction .............................................................................................................................. 5-1

5-2. Abbreviations ........................................................................................................................... 5-1

5-3. Replaceable Parts List ............................................................................................................. 5-1

5-4. Ordering Information ............................................................................................................... 5-1

5-5. Exchange Assemblies ............................................................................................................. 5-1

5-6. Direct Mail Order System ........................................................................................................ 5-2

SECTION VI

Service

6-1. Introduction .............................................................................................................................. 6-1

6-2. Safety Requirements ............................................................................................................... 6-1

6-3. Recommended Test Equipment ............................................................................................. 6-1

6-4. Module Block Diagram and Theory of Operation................................................................... 6-1

6-5. Attenuator Theory of Operation............................................................................................... 6-1

6-6. Main Assembly Theory of Operation....................................................................................... 6-1

6-7. Self-Tests .................................................................................................................................. 6-4

6-8. Troubleshooting ....................................................................................................................... 6-10

6-9. Oscilloscope Module Removal and Replacement ................................................................. 6-18

6-10. Trigger Cable Removal and Replacement ............................................................................. 6-20

6-11. Attenuator Removal and Replacement .................................................................................. 6-21

HP 16532A - Table of Contents

vi

LIST OF TABLES

TABLE TITLE PAGE

1-1. HP 16532A Specifications........................................................................................................ 1-3

1-2. HP 16532A Operating Characteristics..................................................................................... 1-4

1-3. Recommended Test Equipment..............................................................................................1-9

3-1. Performance Test Record ........................................................................................................ 3-17

4-1. Calibration Sequence............................................................................................................... 4-2

5-1. Reference Designator and Abbreviations................................................................................ 5-3

5-2. Replaceable Parts List.............................................................................................................. 5-5

LIST OF FIGURES

FIGURE TITLE PAGE

2-1. Endplate Overlap - Top Sequence........................................................................................... 2-2

2-2. Endplate Overlap - Bottom Sequence..................................................................................... 2-3

3-1. Voltage Measurement Accuracy Test........................................................................................ 3-7

4-1. Endplate Overlap - Top Sequence........................................................................................... 4-3

4-2. Location of the PROTECT/UNPROTECT Switch..................................................................... 4-3

4-3. Default Calibration Display....................................................................................................... 4-4

4-4. Ext Trig Null Calibration Connections...................................................................................... 4-7

4-5. End of Calibration Display........................................................................................................ 4-8

4-6. Endplate Overlap - Top Sequence .......................................................................................... 4-8

5-1. Parts Identification.................................................................................................................... 5-4

6-1. HP 16532A Oscilloscope Block Diagram................................................................................ 6-2

6-2. Startup Screen.......................................................................................................................... 6-4

6-3. Load Test System Screen........................................................................................................ 6-5

6-4. Test System Screen.................................................................................................................. 6-5

6-5. Functional Tests Screen........................................................................................................... 6-6

6-6. Main Test Menu ........................................................................................................................ 6-6

6-7. A/D Test Run Screen................................................................................................................ 6-7

6-8. Stop Field.................................................................................................................................. 6-7

6-9. Exit Test System Screen.......................................................................................................... 6-8

6-10. Troubleshooting Flowchart...................................................................................................... 6-13

6-11. Endplate Overlap - Top Sequence........................................................................................... 6-18

6-12. Endplate Overlap - Bottom Sequence..................................................................................... 6-19

6-13. Oscilloscope Module Exploded View...................................................................................... 6-20

HP 16532A - Table of Contents

vii

TABLE OF CONTENTS

General Information

1-1. Introduction...........................................................................................................................1-1

1-2. Module Covered by Manual.................................................................................................1-1

1-3. Safety Requirements.............................................................................................................1-1

1-4. Product Description..............................................................................................................1-2

1-5. Accessories Supplied...........................................................................................................1-2

1-6. Accessories Available...........................................................................................................1-2

1-7. Specifications........................................................................................................................1-2

1-8. Operating Characteristics.....................................................................................................1-2

1-9. Recommended Test Equipment ..........................................................................................1-2

SECTION I

General Information

1-1. Introduction

The service policy for this instrument is replace-

ment of defective assemblies. This service guidel

contains information for finding a defective

assembly by testing and servicing the HP 16532A

1 GSa/s Oscilloscope Module. Also included in

the guide are installation procedures and a list of

recommended test equipment. This guide is

divided into six sections as follows:

I - General Information

II - Installation

III - Performance Tests

IV - Calibration

V- Replaceable Parts

VI - Service

The General Information Section includes safety

requirements, a product description, and a list of

accessories supplied and of accessories available.

Also included are tables listing specifications and

operating characteristics, and a list of

recommended test equipment.

To complete the service documentation for your

HP 16500 Logic Analysis System, place this

service manual in the 3-ring binder with your other

logic analysis system Service Guides.

1-2. Module Covered by This Manual

The information covered in this manual is for the

HP 16532A 1 GSa/s Oscilloscope Module.

1-3. Safety Requirements

Specific warnings, cautions, and instructions are

placed wherever applicable throughout the

manual. These must be observed during all

phases of operation, service, and repair of the

module. Failure to comply with them violates

safety standards of design, manufacture, and

intended use of this module.

Hewlett-Packard assumes no liability for the failure

of the customer to comply with these safety

requirements.

HP 16532A - General Information

1-1

1-4. Product Description

The HP 16532A Oscilloscope Module is a 1 GSa/s

digitizing oscilloscope. Some of the main features

are:

• 1 GSa/s digitizing for 250 MHz bandwidth sin-

gle shot analysis.

• 8000 samples per channel.

• Automatic pulse parameters, displays time be-

tween markers, acquires until specified time

between markers is captured, performs statis-

tical analysis on time between markers.

• Lightweight miniprobes.

1-5. Accessories Supplied

The following accessories are supplied with the

HP 16532A Oscilloscope module. Quantity one

unless shown otherwise.

• User’s Reference and Programming Refer-

ence set

• Service Guide

• HP 10441A 10:1 probes, Qty 2

• Right angle BNC adapters, Qty 2

• BNC miniprobe adapter

• Master-slave trigger cable

• Operating System Software

1-6. Accessories Available

• 10:1, 100:1, 50 Ω, 10 pf resistive divider probe

set, 1.2 m (HP 10020A)

• BNC-to-BNC cable, 1.2 m (HP 10503A)

• 24-pin IC test clip (HP 10211A)

• BNC-to-BNC ac coupling capacitor

(HP 10240B)

10:1 Probe:

• 1-MΩ, 7.5-pf miniprobe, 1 m (HP 10435A)

1:1 Probes:

• 40-pf miniprobe, 1 m (HP 10438A)

• 64-pf miniprobe, 2 m (HP 10439A)

• 50-Ω miniprobe, 2 m (HP 10437A)

100:1 Probe:

• 10-MΩ, 2.5-pf miniprobe, 2 m (HP 10440A)

1-7. Specifications

Module specifications are listed in table 1-1. These

specifications are the performance standards

against which the module is tested.

1-8. Operating Characteristics

Table 1-2 is a listing of the module operating

characteristics. The operating characteristics are

not specifications, but are the typical operating

characteristics included as additional information

for the user.

1-9. Recommended Test

Equipment

Equipment required to test and maintain the

HP 16532A Oscilloscope Module is listed in table

1-3. Other equipment may be substituted if it

meets or exceeds the critical specifications listed

in the table.

HP 16532A - General Information

1-2

Table 1-1. HP 16532A Specifications

HP 16532A SPECIFICATIONS

Type: 2-channel simultaneous acquisition

Bandwidth

(*,1)

: dc to 250 MHz (real time, dc-coupled)

Maximum Sample Rate: 1 Gigasample per second

Number of Channels: 2, 4, 6, 8 simultaneous channels using the same time base setting(s)

OR

Up to 10 channels with independent time bases for each pair of channels.

Up to 18 channels with the HP 16501A Expansion Frame.

Rise Time

(2)

: 1.4 ns

ADC: 8-bit real time

Vertical Resolution: 8 bits over 4 vertical divisions (± 0.4%)

Waveform Record Length: 8000 points

Time Interval Measurement Accuracy

(*,3,6)

: ± [(0.005% X ∆t)+ (2 x 10

−

6

x delay setting)+ 150 ps]

Vertical (dc) Gain Accuracy

(4)

: ± 1.5% of full scale

DC Offset Accuracy

(*)

: ± (1.0% of channel offset + 2.0% of full scale)

Voltage Measurement Accuracy

(*,5)

: ± [(1.5% of full scale + offset accuracy) + (0.008 x V/div)]

Trigger Sensitivity

(*)

: dc to 50 MHz: 0.063 x full scale, 50 to 250 MHz: 0.125 x full scale

Input Coupling: 1 MΩ: ac and dc, 50 Ω: dc only

Input R (selectable)

(*)

: 1 MΩ: ± 1%, 50 Ω: ± 1%

Input C: Approximately 7 pF

___________________________________________________________________________________________

NOTES:

* Specifications (valid within ± 10° C of auto-calibration temperature, excluding bandwidth− see

note 1 for bandwidth specification.)

1. Upper bandwidth reduces by 2.5 MHz for every degree C above 35° C.

2. Rise time is calculated from the formula:

t

r

=

0.35

bandwidth

3. Specification applies to the maximum sampling rate. At lower rates, the specification is:

± [(0.005% x ∆t)+ (2 x 10

-6

x delay setting) + (0.15 x sample interval)] for bandwidth limited signals

(t

r

= 1.4 x sample interval). Sample interval is defined as

1

sample

rate

4. Vertical gain accuracy decreases 0.08% per degree C from software calibration temperature.

5. Digitizing level = (#vertical divisions)(

1

2

)(

1

LSB

), where LSB= 2

# bits in ADC

6. The Time Interval Measurement Accuracy deteriorates across multiple modules connected as one

unit with each added module.

HP 16532A - General Information

1-3

Table 1-2. HP 16532A Operating Characteristics

HP 16532A OPERATING CHARACTERISTICS

VERTICAL (at BNC)

Vertical Sensitivity Range (1:1 Probe):

4 mV/div to 10 V/div in 1-2-4 increments

DC Offset Range (1:1 Probe):

Vertical Sensitivity Available Offset

4 mV/div to 100 mV/div ± 2 V

> 100 mV/div to 500 mV/div ± 10 V

> 500 mV/div to 2.5 V/div ± 50 V

> 2.5 V/div to 10 V/div ± 250 V

Probe Factors:

Any integer ratio from 1:1 to 1000:1

Maximum Safe Input Voltage:

1 MΩ: ± 250 V [dc + peak ac (< 10 KHz)]

50 Ω: ± 5 VRMS

Channel-to-Channel Isolation:

dc to 50 MHz: 40 dB, 50 MHz to 250 MHz: 30 dB

TIMEBASE

Range:

1 ns/div to 5 s/div

Resolution:

20 ps

Delay Pre-trigger Range:

Time/div Setting Available Delay

1 µs to 5 s/div -8 x (s/div)

1 ns to 500 ns/div -4 µs

Delay Post-trigger Range:

Time/div Setting Available Delay

100 ms to 5 s/div 2.5 ks

1 µs to 50 ms/div 33,500 x (s/div)

1ns to 500 ns/div 16.7 ms

HP 16532A - General Information

1-4

Table 1-2. HP 16532A Operating Characteristics (cont.)

TRIGGERING

Trigger Level Range:

Within display window (full scale and offset)

Trigger Modes:

Immediate:

Triggers immediately after arming condition is met.

Edge:

Triggers on rising or falling edge of any internal channel or external trigger,

count adjustable from 1 to 32,000.

Pattern:

Triggers on entering, exiting, duration greater than, duration less than, and

duration in range for a specified pattern of both internal channels and external

trigger, count adjustable from 1 to 32,000. Duration time range is adjustable

from 20 ns to 160 ms in 10 ns steps. Duration accuracy is approximately ± 3%

± 2 ns.

Auto-Trigger:

If enabled, the module will self-trigger if no trigger condition is found within

approximately 50 ms after arming.

Events Delay:

The trigger can be set to occur on the nth edge or pattern, as specified by the

user. The number of events (n) can be set from 1 to 32,000 events. Maximum

count frequency is 70 MHz.

Intermodule:

Arms another measurement module or triggers the rear panel BNC.

External:

If enabled, the oscilloscope will trigger on an ECL level signal (-1.3 V).

DIGITIZER

Resolution: 8 bits (1 part in 256)

Digitizing Rate: Up to 1 Gigasample per second

Digitizing Technique: Real-time digitizing; each 8000 samples are acquired on a single acquisition

Acquisition Memory Size: 8000 samples per channel

HP 16532A - General Information

1-5

Table 1-2. HP 16532A Operating Characteristics (cont.)

WAVEFORM DISPLAY

Displayed Waveforms:

Eight waveform windows maximum, with scrolling across 96 waveforms.

Display Formats:

Waveforms can be displayed in an overlapping and/or non-overlapping format.

Display capability of A− B and A+ B is also provided.

Display Resolution:

500 points horizontal, 240 points vertical

DISPLAY MODES

Normal (Single):

New acquisition replaces old acquisition on screen.

Accumulate:

New acquisition is displayed in addition to previous acquisitions until screen is

erased.

Average:

New acquisitions are averaged with old acquisitions, with the updated waveform

displayed until erased. Maximum number of averages is 256.

Overlay:

Up to 8 acquired waveforms from separate channels can be overlayed in the

same display area.

Connect-the-dots:

Provides a display of the sample points connected by straight lines.

Waveform Reconstruction:

When there is insufficient data to fill every horizontal location, a post acquisition

reconstruction filter fills in missing data points for time base < 50 ns/div.

Waveform Math:

Display capability of A− B and A+ B functions is provided.

HP 16532A - General Information

1-6

Table 1-2. HP 16532A Operating Characteristics (cont.)

MEASUREMENT AIDS

Time Markers:

Two vertical markers, X and O, are provided for measurements of time and

voltage. Capabilities are: measure voltage at point where X and O markers

cross each analog waveform; measure time from trigger to X, trigger to O, and

X to O; automatic marker placement by specifying percentage of edge, edge

number, and rising or falling edge type; run until X to O > than, < than, in

range, and not in range provides selective event search; X to O statistics (mean,

max, and min) provide analysis of time interval deviation.

Automatic Search:

Searches for a percentage or an absolute voltage level at a positive or negative

edge, count adjustable from 1 to 100.

Auto Search Statistics:

Mean, maximum, and minimum values for elapsed time from X to O markers for

multiple runs. Number of valid runs and total number of runs available.

Automatic Measurements:

The following pulse parameter measurements can be performed automatically:

Frequency Rise time + pulse width

Period Fall time − pulse width

V p-p Preshoot V

amplitude

*

Overshoot

(*gives difference between top and base

voltages; only available over bus)

Grid:

Graticules can be displayed in backround of waveform.

Voltage Markers:

Two horizontal markers, A and B, are provided for voltage measurements.

These markers can each be placed on any acquisition channel trace. A delta

voltage display provides delta V between markers on the same channel or

between two channels.

HP 16532A - General Information

1-7

Table 1-2. HP 16532A Operating Characteristics (cont.)

SETUP AIDS

Autoscale:

Autoscales the vertical and horizontal ranges, offset, and trigger level to display

the input signals. Requires a frequency between 50 Hz and 250 MHz.

Presets:

Scales the vertical range, offset, and trigger level to predetermined values for

displaying ECL or TTL waveforms.

Calibration:

Vertical, trigger, delay, and all defaults. Calibration factors stored in NV-RAM on

the circuit board.

Probe Compensation Source:

External BNC supplies a square wave approximately 0.0 mV to -800 mV into the

open circuit at approximately 1000 Hz.

OPERATING ENVIRONMENT

Temperature:

Instrument, 0° to 55° C (+ 32° to 131° F). Probes and cables, 0° to 65° C (+ 32°

to 149° F).

Humidity:

Instrument, up to 95% relative humidity at + 40° C (+ 104° F). Recommended

disk media, 8% to 80% relative humidity at + 40° C (+ 104° F).

Altitude:

To 4600 m (15,000 ft).

Vibration

Operation:

Random vibration 5-500 Hz, 10 minutes per axis, ~ 0.3 g (rms).

Non-operating:

Random vibration 5-500 Hz, 10 minutes per axis, ~ 2.41 g (rms); and swept

sine resonant search, 5-500 Hz, 0.75 g (0- peak), 5 minute resonant dwell @ 4

resonances per axis.

HP 16532A - General Information

1-8

Table 1-3. Recommended Test Equipment

EQUIPMENT CRITICAL SPECIFICATIONS RECOMMENDED MODEL USE*

Signal Generator Frequency: 1 - 250 MHz at approx .

170 mV RMS resolution

Output Accuracy: ± 1 dB

1 MHz time base accuracy 0.25 ppm

HP 8656B Option 001 P

Dc Power Supply Range: − 35.000 to + 35.000 Vdc, ± 1 mV HP 6114A P

Digital Multimeter 0.1 mV resolution

Accuracy: better than 0.005%

Resistance measurement: better than

0.25% accuracy

HP 3458A P

Power Meter/Sensor 1 - 250 MHz ± 3% accuracy HP 436/8482A P

Power Splitter Outputs differ by < 0.15 dB HP 11667B P

Blocking Capacitor 50 Ω BNC (m-to-f), 0.18 µF, ± 200 V HP 10240B P

Adapter 50 Ω BNC (m)(m) HP 1250-1236 C

Adapter 50 Ω Type N(m)-to-BNC(m) HP 1250-0082 P

Adapter 50 Ω BNC(f)-to-Dual Banana Plug HP 1251-2277 P

Adapter 50 Ω Type N(m)-to-BNC(f) HP 1250-0780 P

Tee Adapter 50 Ω BNC (m)(f)(f) HP 1250-0781 P,C

Cable Type N(m-to-m) 24-inch HP 11500B P

Cable 50 Ω BNC (m-to-m) 48-inch HP 10503A P

Cable 50 Ω BNC (m-to-m) 9 inch HP 10502A C

Cable 50 Ω BNC-SMB HP 16532-61601 C

*P= Performance Tests C= Calibrations

HP 16532A - General Information

1-9

1-10

TABLE OF CONTENTS

Installation

2-1. Introduction ......................................................................................................................... 2-1

2-2. Initial Inspection .................................................................................................................. 2-1

2-3. Preparation for Use ............................................................................................................. 2-1

2-4. Power Requirements .......................................................................................................... 2-1

2-5. Safety Requirements ........................................................................................................... 2-1

2-6. Module Installation .............................................................................................................. 2-1

2-7. Operating Environment ...................................................................................................... 2-4

2-8. Storage ................................................................................................................................ 2-4

2-9. Packaging ........................................................................................................................... 2-4

2-10. Tagging for Service ............................................................................................................. 2-4

Page is loading ...

HP 1GSa/s User manual

This manual is also suitable for

HP 1GSa/s User manual

Related papers

Other documents