Princeton AGX700 User manual

Brand: Princeton

Model: AGX700

Category: Monitors CRT

Type: User manual

Princeton AGX700 is a 17” color monitor with a 16” viewable display. It is compliant with FCC Class B digital device limits and does not exceed the Class B limits for radio noise emissions from digital apparatus as set out in the Radio Interference Regulations of the Canadian Department of Communications. To comply with these limits, always use shielded signal cord and shielded power cord supplied with this unit.

AGX700

17”COLOR

MONITOR

BY PRINCETON

REFERENCE GUIDE

16” VIEWABLE

This Page left blank intentionally.

I. FCC Compliance Statement 4

II. Safety Instructions 5

III. Sicherheitshinweise 6

IV. TUV 7

1. Introduction 9

2. Installation 11

3. Controls & Functions 12

4. Timing Guide 16

5. Power Management 17

Appendix A: Specifications 18

Appendix B: Pin Assignment 19

Troubleshooting and Q&A 20

USER 'S MA NU AL

A G X 7 0 0

This equipment has been tested and found to comply with the limits for a

Class B digital device, pursuant to Part 15 of the FCC Rules. These limits

are designed to provide reasonable protection against radio frequency

interference in a residential installation. This equipment generates, uses,

and can radiate radio frequency energy. If not installed and used in

accordance with the instructions, it may cause interference to radio

communications. However, there is no guarantee that interference will not

occur in a particular installation. If this equipment does cause

interference to radio or television reception (this can be determined by

turning this equipment off and on), the user is encouraged to try to

correct the interference by one or more of the following measures:

• Reorient or relocate the receiving antenna.

• Increase the separation between this equipment and the receiver.

• Connect this equipment to an outlet on a circuit different from that to

which the receiver is connected.

• Consult the dealer or an experienced radio/TV technician for help.

CA U T I O N:

To comply with the limits for an FCC Class B computing device, always use

the shielded signal cord and shielded power cord supplied with this unit .

The Federal Communications Commission warns the user that changes or

modifications to the unit not expressly approved by the party responsible

for compliance could void the user’s authority to operate the equipment.

If necessary, the user should contact the dealer or an experienced radio/

television technician for additional suggestions. The user may find the

Federal Communications Commission booklet, “How to Identify and

Resolve Radio-TV Interference Problems,” helpful. This booklet is available

from the U.S. Government Printing Office, Washington D.C., Stock No.

0 0 4 - 0 0 0 - 0 0 3 4 5 - 4 .

This digital apparatus does not exceed the Class B limits for radio noise

emissions from digital apparatus set out in the Radio Interference

Regulations of the Canadian Department of Communications.

DOC AV I S D E CO N F O R M A T I O N:

Le présent appareil numérique n’emet pas de bruits radioélectriques

dépassant les limites applicable aux appareils numériques de la class B

prescrites dan le Règlement sur le brouillage radioélectriques édicté par

le ministère des Communications du Canada.

Read all of these instructions.

Save these instructions for later use.

Follow all warnings and instructions marked on the product.

Unplug this product from the wall outlet before cleaning. Do not use

liquid cleaners or aerosol cleaners. Use a damp cloth for cleaning.

Do not use this product near water.

Do not place this product on an unstable cart, stand, or table. The

product may fall, causing serious damage to the product.

Slots and openings in the cabinet and the back or bottom are

provided for ventilation. To ensure reliable operation of the product

and to protect it from overheating, these openings must not be

blocked or covered. The openings should never be blocked by

placing the product on a bed, sofa, rug, or other similar surface.

This product should never be placed near or over a radiator or heat

unless proper ventilation is provided.

This product should be operated from the type of power source

indicated on the marking label. If you are not sure of the type of

power available, consult your dealer or local power company.

This product is equipped with a 3-wire grounding type plug, a plug

having a third (grounding) pin. This plug will only fit into a grounding

type power outlet. This is a safety feature. If you are unable to insert

the plug into the outlet, contact your electrician to replace your

obsolete outlet. Do not defeat the purpose of the ground type plug.

Do not allow anything to rest on the power cord. Do not locate this

product where persons will walk on the cord.

If an extension cord is used with this product, make sure that the

total of the amperage ratings on the products plugged into the

extension cord does not exceed the extension cord’s amperage

rating. Also, make sure that the total of all products plugged into

the wall outlet does not exceed 15 amperes.

Never push objects of any kind into this product through cabinet

slots as they may touch dangerous high voltage points or cause

short circuits, which could result in electric shock or fire hazard.

Never spill liquid of any kind on the product.

Do not attempt to service this product yourself, as opening or

removing covers may expose you to dangerously high voltages or

other risks. Refer all servicing to qualified service personnel.

Unplug this product from the wall outlet and refer servicing to a

qualified service personnel under the following conditions:

When the power cord or plug is damaged or frayed.

If liquid has been spilled into the product.

If the product has been exposed to rain or water.

If the product does not operate normally when the operating

instructions are followed. Adjust only those controls that are

covered by the operating instructions since improper adjustment

of other controls may result in damage, and will often require

extensive repair work to restore the product to normal operation.

If the product has been dropped or the cabinet has been

damaged.

If the product exhibits a distinct change in performance,

indicating a need for service.

Page is loading ...

The AGX700 is a high-performance 17-inch (16.0-inch viewable) multi-

scan color monitor that supports high refresh rates for no flicker. The

AGX700 is capable of resolutions up to 1280 x 1024, and the intelligent

microprocessor-based design enables the AGX700 to automatically

synchronize to most common video modes.

The AGX700 employs the vertically flat screen of advanced Trinitron®

technology that produces straighter lines eliminating much of image

distortion found on a conventional sphercal screen. Its aperture grille

design, which features a series of unbroken vertical stripes allowing more

of the electron beam to pass through to the phosphor layer, produces a

clearer and brighter picture. In addition, ambient light reflection is

minimized to provide a screen image that reduces eyestrain and fatigue

With Auto Setup, pressing a single button adjusts the picture size and

position automatically. Self-diagnostic capabilities quickly determine if

the monitor is working properly, or if problems lie elsewhere.

The AGX700 is Plug and Play compatible and features EPA Energy Star-

compliant, VESA DPMS-compatible power management.

We truly believe you will enjoy using the AGX700. Thank you for making

our product your choice.

• Multi-scanning at horizontal frequencies of 30kHz to 70kHz, vertical

frequencies of 50Hz to 140Hz

• 17-inch (16.0-inch viewable) Sony Trinitron® picture tube

• Aperture grille design for excellent brightness and color fidelity

• 0.25mm Aperture grille pitch

• Microprocessor-based design with digital controls

• Automatic display setup button

• Windows 95/98 Plug and Play (VESA DDC1, DDC2B, DDC/CI)

• 11 preset timing modes

• Overscan capability for increased viewable area

• Unlimited colors

• Compatible with standard IBM VGA, extended VGA, Super VGA, IBM

XGA, SXGA, as well as VESA ergonomic standards

• Compatible with Apple Power Macintosh

• Universal Power Supply

• Tilt and swivel base

• TCO ’95 and MPR II compliant

• NUTEK and EPA Energy Star compliant power saving

• VESA Display Power Management Signaling (DPMS) compatible

Before operating this monitor, please make sure that all the items listed

below are present in your package:

• AGX700 monitor

• AC power cord

• Drivers and utilities CD-ROM

• User’s manual

• Warranty information

If any of the above items is found missing, please contact your dealer, or

call Princeton Graphic Systems.

Princeton Graphic Systems

2801 South Yale Street

Santa Ana, CA 92704

Tel: 1-800-747-6249 (U.S. and Canada) or 1-714-751-8405

Fax:1-714-751-5736

Internet Address: www.prgr.com

No tools are required to install the AGX700. Simply follow the

instructions outlined in the next few pages.

Connect the female end of the power cable to the power input

receptacle on the back panel of the AGX700. Then plug the male end of

the power cable into an AC outlet.

Attach the loose end of the signal cable to the display adapter. Be

cautious in inserting the cable properly into the display adapter. If the

cable does not seem to fit it may be facing the wrong direction. Turn the

cable over and try to match the shape of the connector with that of the

display adapter.

Switch ON the power to both the AGX700 and your computer. There will

be a short delay before the display appears.

Adjust the controls, if necessary, to obtain the best display. Instructions

on how to use the On-Screen Display controls and the Auto Setup button

may be found in the next chapter, “Controls and Functions.”

Adjust the tilt and swivel base for your maximum viewing comfort. The

illustrations below illustrate the adjustment range for tilt and swivel.

To minimize eye fatigue, we suggest you allow a minimum

viewing distance of 18 inches.

6 5 4 3 2 1

Press this button to turn the power ON or OFF. There will be a short delay

before the display appears.

This LED indicator turns green when the power is switched ON and the

power cord is properly attached.

Activates the On-Screen Display (OSD) menu. While the OSD menu is

active, use this button to select the highlighted control for adjustment.

Activates the Brightness/Contrast controls if the OSD menu is not active.

While the OSD menu is active, use this button to move the highlight up to

the previous item in the OSD menu. Once a control is selected, use this

button to adjust the display setting.

Activates the Brightness/Contrast control if the OSD menu is not active.

While the OSD menu is active, use this button to move the highlight down

to the next item in the OSD menu. Once a control is selected, use this

button to adjust the display setting.

Automatically sizes the display to fill the screen and adjusts the contrast

and brightness controls to a comfortable level. For this feature to function,

the computer and graphics card must be set to one of the 11 preset timing

modes. (See page 16.) While the OSD menu is active, this button is also

used to save any adjustments and exit the current menu.

The AGX700 features a PreVu™ On-Screen Display (OSD) menu with

animated control icons designed to make adjusting your monitor display

settings a more user-friendly process. When highlighted, the icon

illustrates the control function to assist you in identifying which control

needs adjustment.

Before activating the OSD menu, you can use the Auto Setup button

to automatically adjust the display to the proper size and

brightness/contrast levels. The monitor must be running at one of the 11

factory preset timing modes to utilize this feature. (See page 16.)

The OSD menu activates automatically when you press the Enter

button on the front of the monitor. The OSD remains centered on the

screen while you make your adjustments. Use either the or button

to move the highlight to the control you want to adjust, then press the

Enter button to select that control. When you select a control, a submenu

of the control with a status bar appears. The status bar indicates in which

direction, from the factory preset, your adjustments are being made. Use

the or buttons to adjust the control. In addition, a second control

icon will appear allowing you to toggle between the control originally

selected and a second control (for example, Contrast/Brightness). Use

the Enter button (while in adjustment mode) to switch between the two

controls.

The Contrast/Brightness controls can also be adjusted without activating

the OSD menu. Just press either the or buttons on the front of the

monitor.

When you have finished making adjustments, press to save the setting

and exit out of the adjustment mode back to the main PreVu™ menu for

additional display adjustment. Or, simply leave the buttons untouched for

approximately 15 seconds and the setting(s) will be saved automatically.

While in the main menu, press the button to exit the On-Screen Display

e n t i r e l y .

Selecting this control allows you to make adjustments to the black level

of the display screen.

Selecting this control allows you to make adjustments to the luminosity

level of the display screen.

Select this control, then use the and buttons to center the image

horizontally on the display screen.

Select this control, then use the and buttons to expand or decrease

the image width to horizontally fill the display screen.

Select this control, then use the and buttons to center the image

vertically on the display screen.

Select this control, then use the and buttons to expand or decrease

the image height to vertically fill the display screen.

Select this control, then use the and buttons to straighten the sides

of the image by pulling them in opposing directions.

Select the Pincushion control, then use the button to select Pin

Balance. Use the and buttons to straighten the sides of the image

by pulling them in the corresponding direction.

Select this control, then use the and buttons to straighten the top

and bottom corners(press ) of the image by pulling them in opposing

directions.

Select this control, then use the and buttons to even the widths of

the top and bottom of the display (pulling the sides in opposing

directions).

Select this control, then use the and buttons to center the top and

bottom of the display (pulling the sides in the corresponding direction).

Select this control, then use the and buttons to rotate the image

until the sides of the image are parallel to the edge of the bezel.

Select this control, then use the button to select moiré. Use the

and buttons to decrease the moiré, an interference pattern that

causes some dithered colors to “shimmer” or appear uneven.

Select this control, then use the and buttons to scroll to the desired

color temperature. Use the button to select either the 9300K, 6500K

or 5500K, or select User for a custom RGB setting.

Select “Color 4: User,” then use the button to scroll up and down the

RGB menu to R (Red). Use the and buttons to adjust the red level

of the display.

Select “Color 4: User,” then use the button to scroll up and down the

RGB menu to G (Green). Use the and buttons to adjust the green

level of the display.

Select “Color 4: User,” then use the button to scroll up and down the

RGB menu to B (Blue). Use the and buttons to adjust the blue

level of the display.

Select this control, then use the and buttons to choose from:

English, German (Deutsch), Spanish (Español), Italian (Italiano) or

French (Français)

Select this control, then use the button to select in which direction to

move the OSD menu. Use the and buttons to move the OSD menu.

Demagnetizes the CRT when the display becomes discolored or washed

out in appearance. The monitor will automatically degauss on startup if

the monitor has been off for at least 20 minutes.

Resets the display settings to the original factory preset values. Press

and hold down the button until the progress bar disappears.

640 480 31.5 60

720 400 31.5 70

640 480 37.5 75

800 600 46.9 75

1024 768 60.0 75

1152 864 67.5 75

1280 1024 64.0 60

640 480 43.3 85

800 600 53.7 85

1024 768 68.7 85

832 624 49.7 75

The AGX700 is a multi-scan monitor. It operates at horizontal frequencies

between 30kHz and 70kHz, vertical frequencies between 50Hz and

140Hz. Because of its microprocessor-based design, it offers auto-

synchronization and auto-sizing capabilities. This monitor offers 11 pre-

programmed settings, which are listed in the table to the right.

These preset modes cover most of the common video modes supported

by popular display adapters. However, each adapter’s implementation of

these video modes may vary slightly in timings. If you find it necessary to

make minor display adjustments (horizontal and vertical size and

position), please refer to Chapter 3 for instructions on making these

adjustments.

Note that the monitor is not limited to these preset factory timing modes.

In fact, because the monitor is multi-scanning, it can accept any signal

within its frequency range of 30-70kHz horizontal and 50-140Hz vertical.

If, however, you would like to use one of the preset timing modes, please

refer to your display adapter manufacturer’s installation guide for

instructions on how to make these changes. The refresh rate is controlled

by the display adapter. Most display adapters provide a software utility or

hardware DIP switches that allow you to change the frequency used for

each resolution.

MODE

NAME

RESOLUTION

H V

FREQUENCY

H(kHz) V(Hz)

The power management feature of the AGX700 enables the monitor to

recognize VESA DPMS (Display Power Management Signaling) signals

from an VESA DPMS video adapter and power down to less than 8 watts

of power consumption. A VESA DPMS compatible video adapter achieves

the signaling by setting horizontal, vertical, or both synchronization signals

to inactive. The AGX700 recognizes all four types of signals and enters

into the appropriate mode. In Standby, Suspend and Active Off modes,

t h e AGX700 still maintains a detection and CRT heater circuitry to ensure

fast recovery time when both synchronization signals are active again.

The power management feature of the AGX700 is comprised of four

stages: On (green), Standby (amber), Suspend (amber/green), and

Active Off (amber/green). In the Standby and Suspend modes, the high

voltage function of the monitor shuts down while the heater circuitry

remains active. In the Active Off mode, all circuitry in the monitor is shut

down except for a low power detection circuit. This circuit allows the

monitor to “wake up” when the mouse is moved or a key on the keyboard

is pressed.

On Less than 100W

Standby Less than 15W

Suspend Less than 15W

Active Off Less than 8W

On Green

Standby Amber

Suspend Flashing Amber/Green

(1 flash/second)

Active Off Flashing Amber/Green

(1 flash/2 seconds)

17” (16.0” viewable) nonglare, anti-

static, dark Sony Trintron® tube with

aperture grille and 90° deflection

0.25mm

1280 x 1024 @ 66Hz

1024 x 768 @ 85Hz

Unlimited

Auto-synchronizing 50Hz to 140Hz

Auto-synchronizing 30kHz to 70kHz

108.5MHz at -3 dB (nominal)

Default: 11.8” x 8.9” (300mm x 225mm)

Overscan: 12.9” x 9.5” (327mm x 240mm)

VIDEO: Analog 0.7 V

p - p

/75 Ohm

SYNC: Separate and Composite TTL Level

100 to 240V

@ 50/60Hz;

EPA Energy Star

S M

compliant; VESA®

DPMS

™

compatible; NUTEK

compliant; On: <100W, Standby:

<15W, Suspend: <15W, Active Off:

<8W

32 to 104°F (0 to 40°C)

10 to 80% (noncondensing)

16.1” x 16.1” x 17.7”

(410mm x 410mm x 449mm)

Net: 39.9 lb. (18.1kg)

Gross: 46.6 lb.(21.15kg)

UL, CSA, CE, DHHS, FCC-B, VCCI,

SEMKO, TCO ’95, NUTEK, EPA Energy

Star

S M

, VESA® DPMS

™

Apple Macintosh Adapter (optional) Sun

SPARCStation Adapter (optional)

The pin assignment of the connectors is listed below. This is for your information only. Please do not attempt to devise your own connections as it

may damage the monitor.

1 Red

2 Green

3 Blue

4 No Connection

5 DDC Return

6 Red Ground

7 Green Ground

8 Blue Ground

9 No Connection

10 Sync. Ground

11 Ground

12 SDA

13 Horizontal Sync.

14 Vertical Sync.

15 SCL

Make sure all of the power connections are secure. If the monitor is plugged into a surge protector, make sure the surge protector is switched on.

Check all the signal cable connections and make sure that they are secure. Adjust both the contrast and brightness controls to the highest settings. If

you see a faint gray color appearing on the screen, the monitor is functioning properly but not receiving any signal from the computer’s display adapter.

Also, the AGX700 features a self test screen. You can activate the self test screen by turning off the monitor, detaching the signal cable from the

computer and turning the monitor back on. A self test screen will appear showing three distinct red (left), green (center) and blue (right) squares. If you

can see this screen with all three distinct colors in the proper positions, your monitor is working properly.

You can activate the self test screen (described above) to determine if the monitor is working properly. If you can see the three distinct red, green and

blue squares, your monitor is working properly. Please check your connector cable and display adapter and/or display driver. Make sure that no pins in

the connector are bent and that the connection to the monitor and computer are secure.

The sound you hear indicates that the degauss function is activated. Every time the monitor is switched on, it will go through the degaussing process

which helps eliminate any purity problems.

The frequency and resolution displayed on a monitor is controlled by the display driver and operating system. The monitor simply responds to the signal it

receives from the display adapter and is not able to change the resolution on its own. Most display adapter manufacturers provide software drivers and

utilities that allow you to use different resolutions for different applications. Please consult your display adapter manual or dealer for more information.

The microprocessor allows precise screen size control of the image for several different modes. Normally, the image size will vary when changing

between different resolutions. With the microprocessor, the monitor is able to remember the size for each different mode and recall them automatically.

In order to fully utilize the Plug and Play feature, the computer must be equipped with a Plug and Play (DDC2B) display adapter and running with a

Plug and Play capable operating system (for example, Windows 95) or utility program that enables the Plug and Play function automatically.

Trinitron® CRT uses rows of very fine metal strips that run vertically down the screen. In order to stabilize these fine strips from shimmering, two

horizontal wires are put across the vertical strips. These tow lines are usually visible only when looking at a bright, solid background.

The refresh rate is controlled by the display adapter. Most display adapters provide a software utility or hardware DIP switches that allows you to

change the frequency used for each resolution.

Maximum refresh rates depend on the display adapter support. As far as monitor specification limitations are concerned, they are approximately:

640 x 480 at 135Hz

800 x 600 at 110Hz

1024 x 768 at 87Hz

1280 x 1024 at 66Hz

The earth’s magnetic field may be interfering with the magnetic field generated by the monitor causing a slight rotation of the image. The higher the

performance of a monitor, the more susceptible will the monitor be to such interference. To get the best alignment, orient the monitor so that the face

of the screen faces east, and choose the Rotation control from the OSD menu.

A slight amount of pincushion will be normal for the display however, an excessive amount is not allowable. To correct for this distortion, choose the

Pincushion control from the OSD menu. In general, you should expect to see less than 3/16” pincushion when measured with the naked eye.

One of the limitations of a CRT screen is that it is impossible for the focus to be uniform across the entire area. In general, a monitor is adjusted so that

the focus is best in an area around the center, in which case the overall focus is optimized. However, the image in the corner should always be

r e a d a b l e .

The ghosting may be due to a reflection in the signal. This usually occurs if an extension signal cable is installed or if the signal cable is not fastened to

the back of the display adapter.

The AGX700 monitor was released after Windows 95/98. An additional monitor INF file (PGS.INF) may be needed for Windows 95/98. The file and

instructions can be found on the CD-ROM included with your monitor or it can be downloaded via the internet at www.prgr.com.

Princeton Graphic Systems is not responsible for printing or clerical errors. Princeton, the Princeton logo, Coloright, and PreVu are trademarks of Princeton