Pioneer PDP-42A3HD User manual

Category
LCD TVs
Type
User manual
PLASMA DISPLAY SYSTEM
SYSTEME D’ÉCRAN PLASMA
SISTEMA DE PANTALLA DE PLASMA
PDP-42A3HD
PDP-4214HD
Operating Instructions
Mode d’emploi
Manual de instrucciones
Register Your Product at
www.pioneerelectronics.com (US)
www.pioneerelectronics.ca (Canada)
01-PDP42A3HD-Eng (Cover) 05.4.20, 4:29 PM1
Read these instructions.
Keep these instructions.
Heed all warnings.
Follow all instructions.
Do not use this apparatus near water.
Clean only with dry cloth.
Do not block any ventilation openings. Install in
accordance with the manufacturer’s instructions.
Do not install near any heat sources such as
radiators, heat registers, stoves, or other apparatus
(including amplifiers) that produce heat.
Do not defeat the safety purpose of the polarized or
grounding-type plug. A polarized plug has two
blades with one wider than the other. A grounding
type plug has two blades and a third grounding
prong. The wide blade or the third prong are
provided for your safety. If the provided plug does
not fit into your outlet, consult an electrician for
replacement of the obsolete outlet.
Protect the power cord from being walked on or
pinched particularly at plugs, convenience
receptacles, and the point where they exit from the
apparatus.
1)
2)
3)
4)
5)
6)
7)
8)
9)
10)
Only use attachments/accessories specified by the
manufacturer.
Use only with the cart, stand, tripod, bracket, or
table specified by the manufacturer, or sold with the
apparatus. When a cart is used, use caution when
moving the cart/apparatus combination to avoid
injury from tip-over.
Unplug this apparatus during lightning storms or
when unused for long periods of time.
Refer all servicing to qualified service personnel.
Servicing is required when the apparatus has been
damaged in any way, such as power-supply cord or
plug is damaged, liquid has been spilled or objects
have fallen into the apparatus, the apparatus has
been exposed to rain or moisture, does not operate
normally, or has been dropped.
11)
12)
13)
14)
Note to CATV system installer.
This reminder is provided to call the CATV system installer’s attention to Article 820-40 of the NEC that provides
guidelines for proper grounding and, in particular, specifies that the cable ground–shall be connected to the
grounding system of the building, as close to the point of cable entry as practical.
02-PDP42A3HD-Eng (02-03) 05.4.20, 4:29 PM2
English
WARNING: THE APPARATUS IS NOT WATER-
PROOFS, TO PREVENT FIRE OR SHOCK HAZARD, DO
NOT EXPOSE THIS APPLIANCE TO RAIN OR MOISTURE
AND DO NOT PUT ANY WATER SOURCE NEAR THIS
APPARATUS, SUCH AS VASE, FLOWER POT, COSMET-
ICS CONTAINER AND MEDICINE BOTTLE ETC.
WARNING: Handling the cord on this product or
cords associated with accessories sold with the prod-
uct will expose you to lead, a chemical known to the
State of California and other governmental entities to
cause cancer and birth defects or other reproductive
harm. Wash hands after handling.
NOTE: This equipment has been tested and found to
comply with the limits for a class B digital device, pur-
suant to Part 15 of the FCC Rules. These limits are de-
signed to provide reasonable protection against harm-
ful interference in a residential installation. This equip-
ment generates, uses, and can radiate radio frequency
energy and, if not installed and used in accordance with
the instructions, may cause harmful interference to ra-
dio communications. However, there is no guarantee that
interference will not occur in a particular installation. If
this equipment does cause harmful interference to ra-
dio or television reception, which can be determined by
turning the equipment off and on, the user is encour-
aged to try to correct the interference by one or more of
the following measures:
— Reorient or relocate the receiving antenna.
— Increase the separation between the equipment and
receiver.
— Connect the equipment into an outlet on a circuit
different from that to which the receiver is connected.
— Consult the dealer or an experienced radio/TV tech-
nician for help.
Information to User
Alteration or modifications carried out without appro-
priate authorization may invalidate the user’s right to
operate the equipment.
[For Canadian model]
This Class B digital apparatus complies with Canadian
ICES-003.
CAUTION:
This product satisfies FCC regulations when shielded
cables and connectors are used to connect the unit to
other equipment. To prevent electromagnetic interfer-
ence with electric appliances such as radios and televi-
sions, use shielded cables and connectors for connec-
tions.
IMPORTANT NOTICE: The serial number for this
equipment is located on the rear panel. Please write
this serial number on your enclosed warranty card and
keep it in a secure area. This is for your security.
WARNING: Be sure to plug this equipment into a
grounding-type AC outlet.
02-PDP42A3HD-Eng (02-03) 05.4.20, 4:29 PM3
4
En
Contents
Thank you for buying this Pioneer product.
Please read through these operating instructions so you will know how to operate your model properly. After you have finished
reading the instructions, put them away in a safe place for future reference.
In some countries or regions, the shape of the power plug and power outlet may sometimes differ from that shown in the explana-
tory drawings. However the method of connecting and operating the unit is the same.
01 Important User Guidance Information
02 Safety Precautions
03 Supplied Accessories
04 Part Names
Plasma Display ................................................................... 11
Remote control unit ............................................................ 13
05 Preparation
Installing the Plasma Display ............................................ 15
Preventing the Plasma Display from Falling Over ........... 15
Preparing the remote control unit ..................................... 16
Inserting batteries......................................................... 16
Cautions regarding batteries ....................................... 16
Allowed operation range of the
remote control unit .................................................... 16
Cautions regarding the remote control unit .............. 17
Cable connections for watching digital and/or conventional
TV channels ....................................................................... 17
Connecting to an Aerial ............................................... 17
Connecting the power cord ............................................... 18
06 Basic Operations
Turning the power on and off (Standby) ........................... 19
Watching TV channels........................................................ 20
Selecting the analog and digital channels ................. 20
Changing channels ...................................................... 20
Changing the volume and sound ................................ 21
Displaying Information ....................................................... 21
Setting MTS/SAP mode ...................................................... 22
Using the multiscreen functions ....................................... 22
07 Menu Setup
Menu configuration ............................................................ 24
Menu operations ................................................................. 24
08 Tuner Setup
Setting up TV channels ...................................................... 25
Scanning Channels Automatically ............................. 25
Scanning Analog Channels Manually ........................ 25
Scanning Digital Channels Manually ......................... 26
Editing Channel List ..................................................... 26
Display the Channel List .............................................. 27
Setting up the Parental Control ......................................... 27
Activating the Parental Control ......................................... 28
Setting the voluntary movie rating
system (MPAA) ................................................................. 28
Setting the TV Ratings .................................................. 29
Setting up the Canadian rating systems .................... 29
Blocking No rating programs ...................................... 30
Viewing Closed Caption Information................................. 30
Setting the Current Date and Time ................................... 31
9 Adjustments and Settings
Sleep Timer .......................................................................... 32
Picture adjustments ........................................................... 32
Selecting the Picture Mode ......................................... 32
Customizing the Picture Settings ............................... 33
Using the Noise Reduction Feature ............................ 33
Setting the Color Temperature .................................... 34
Selecting the Sound Effect ................................................ 34
Customizing the Sound Settings ....................................... 35
Adjusting the Volume Automatically................................. 35
Setting the Surround Sound .............................................. 35
Setting up External Digital Sound ..................................... 35
Changing the Screen Size .................................................. 36
Viewing the Input Source ................................................... 36
Setting for the language of on-screen display ................. 36
Setting for the audio language of digital TV ..................... 37
Screen Saver ....................................................................... 37
Setting the Full White mode ........................................ 37
Power Control ...................................................................... 38
Switching the Plasma Display Off Automatically ...... 38
Setting the Plasma Display On Time .......................... 38
Setting the Plasma Display Off Time .......................... 38
10 Enjoying through External Equipment
Connecting to the External Input ...................................... 39
Connecting to the Component Input ................................ 40
Connecting to the HDMI Input .......................................... 41
Connecting to the Monitor Output .................................... 41
Connecting to the DIGITAL Audio Output ......................... 42
11 Appendix
Troubleshooting .................................................................. 43
Specifications ...................................................................... 45
03-PDP42A3HD-Eng (04) 05.4.20, 4:30 PM4
01Important User Guidance Information
English
5
En
In order to obtain maximum enjoyment from this Pioneer
PureVision PDP-42A3HD/PDP-4214HD Plasma Display System,
please first read this information carefully.
With the Pioneer PureVision PDP-42A3HD/PDP-4214HD, you
can be assured of a high quality Plasma Display System with
long-life and high reliability. To achieve images of exceptional
quality, this Pioneer Plasma Display System incorporates state-
of-the-art design and construction, as well as very precise and
highly advanced technology.
Over the course of its lifetime, the luminosity of the Pioneer
PDP-42A3HD/PDP-4214HD Plasma Display System will
diminish very slowly, such as with all phosphor-based screens
(for example, a traditional tube-type television). To enjoy
beautiful and bright images on your Pioneer Plasma Display
System for many years to come, please carefully read and
follow the usage guidelines below.
Usage guidelines
All phosphor-based screens (including conventional tube-type
televisions) can be affected by displaying static images for a
prolonged period. Plasma Display Systems are no exception to
this rule. After-image and permanent effects on the screen can
be avoided by taking some basic precautions. By following the
recommendations listed below, you can ensure longer and
satisfactory results from your plasma:
Whenever possible, avoid frequently displaying the same
image or virtually still moving pictures (e.g. closed-captioned
images or video game images which have static portions).
Avoid viewing the On Screen Display for extended periods,
from a DVD player, VCR, and all other components.
Do not leave the same picture freeze-framed or paused
continuously over a long period of time, when using the still
picture mode from a TV, VCR, DVD player or any other
component.
Images which have both very bright areas and very dark
areas side by side should not be displayed for a prolonged
period of time.
When playing a game, the “GAME” mode setting within “AV
Selection” is strongly recommended. However, please limit its
use to less than 2 hours at a time.
•After playing a game, or any still image, it is best to view a
normal moving picture in the “WIDE” or “FULL” screen setting
for over 3 times longer than the previous still/moving image.
•After using the Plasma Display System, always switch the
display to “STANDBY” mode.
Installation guidelines
The Pioneer PureVision PDP-42A3HD/PDP-4214HD Plasma
Display System incorporates a very thin design. To ensure
safety, please take the proper measures to mount or install the
Plasma Display, in order to prevent the unit from tipping over in
the event of vibration or accidental movement.
This product should be installed by using only parts and
accessories designed by PIONEER. Use of accessories other
than the PIONEER installation bracket may result in instability,
and could cause injury. For custom installation, please consult
the dealer where the unit was purchased. To ensure correct
installation, experienced and qualified experts must install the
unit. PIONEER will not be held responsible for accident or
damage caused by the use of parts and accessories manufac-
tured by other companies.
To avoid malfunction and overheating when installing, make
sure that the vents on the main unit are not blocked. To ensure
proper heat emission:
Distance the unit slightly from other equipment, walls, etc.
For the minimum space required around the unit, see page
14.
Do not fit the unit inside narrow spaces where ventilation is
poor.
Do not cover with a cloth, etc.
Clean the vents on the sides and rear of the unit to remove
dust build-up by using a vacuum cleaner set to its lowest
suction setting.
Do not place the product on a carpet or blanket.
Do not reverse the product.
Using the unit without proper ventilation may cause the
internal temperature to rise, and could result in possible
malfunction. When the surrounding or internal temperature
exceeds a certain degree, the display will automatically power
off in order to cool the internal electronics and prevent a
hazardous occurrence.
Malfunction can be caused by many factors: inappropriate
installation site, improper assembly/installation/mounting,
improper operation of or modifications made to this product.
However, PIONEER cannot be held responsible for accidents or
malfunction caused by the above.
The following are typical effects and characteristics of a
phosphor-based matrix display and as such, are not covered by
the manufacturer’s limited warranties:
•Permanent residual images upon the phosphors of the panel.
The existence of a minute number of inactive light cells.
•Panel generated sounds, examples: Fan motor noise, and
electrical circuit humming / glass panel buzzing
01 Important User Guidance Information
04-PDP42A3HD-Eng (05-10) 05.4.20, 4:30 PM5
01 Important User Guidance Information
6
En
PIONEER bears no responsibility for any damages arising from
incorrect use of the product by you or other people, malfunc-
tions when in use, other product related problems, and use of
the product except in cases where the company must be liable.
Information of pixel defect
Plasma Display displays images consisting of hundreds of
thousands of minute pixels (light emitting cells), and there is a
possibility of inactive, flashing or continually illuminated pixels.
Infrared rays
The Plasma Display releases infrared rays because of its
characteristics. Depending on how the Plasma Display is in
use, the remote controls of nearby equipment may be adversely
affected or wireless headphones using infrared rays are
interfered by noise. If this is the case, place that equipment at a
location where its remote control sensor is not affected.
Radio interference
While this product meets the required specifications, it emits a
small amount of noise. If you place such equipment as an AM
radio, personal computer, and VCR close to this product, that
equipment may be interfered. If this happens, place that
equipment far enough from this product.
Plasma Display driving sound
The screen of the Plasma Display is composed of extremely fine
pixels and these pixels emit light according to received video
signals. This principle may make you hear buzz sound electrical
circuit hamming from the Plasma Display.
Also note that the rotation speed of the cooling fan motor
increases when the ambient temperature of the product
becomes high.
You may hear the sound of the fan motor at that time.
Do not attach such items as labels and tape to the
product
This may result in the discoloration or scratch of the cabinet.
When not using the product for a long period of time
If you do not use the product for a long period of time, the
functions of the product may be adversely affected. Switch on
and run the product occasionally.
Condensation
Condensation may take place on the surface or inside of the
product when the product is rapidly moved from a cold place
to a warm place or just after a heater is switched on in winter
morning, for example. When condensation takes place, do
not switch on the product and wait until condensation
disappears. Using the product with condensation may result
in malfunction.
Cleaning the screen
When cleaning the screen of this product, gently wipe it with
a soft dry cloth; the supplied cleaning cloth or other similar
cloths (e.g., cotton and flannel). If you use a hard cloth or rub
the screen hard, the surface of the screen will be scratched.
If you clean the surface of the screen with a wet cloth, water
droplets on the surface may enter into the product, resulting
in malfunction.
Cleaning the cabinet
When cleaning the cabinet of this product, gently wipe it with
a soft dry cloth; the supplied cleaning cloth or other similar
cloths (e.g., cotton and flannel). If you use a hard cloth or rub
the cabinet hard, the surface of the cabinet will be scratched.
The cabinet of this product is mostly composed of plastic. Do
not use chemicals such as benzine or thinner to clean the
cabinet. Using these chemicals may result in quality deterio-
ration or coating removal.
Do not expose the product to volatile gas or fluid such as
pesticide. Do not make the product contact with rubber or
vinyl products for a long period of time. The effect of plasti-
cizer in the plastic may result in quality deterioration or
coating removal.
If you clean the surface of the cabinet with a wet cloth, water
droplets on the surface may enter into the product, resulting
in malfunction.
Handles at the rear of the Plasma Display
Do not remove the handles from the rear of the Plasma
Display.
When moving the Plasma Display, ask another person for
help and use the handles attached to the rear of the Plasma
Display. Do not move the Plasma Display by holding only a
single handle. Use the handles as shown.
Do not use the handles to hang the product when installing
or carrying the product, for example. Do not use the handles
for the purpose of preventing the product from tilting over.
04-PDP42A3HD-Eng (05-10) 05.4.20, 4:30 PM6
01Important User Guidance Information
English
7
En
Panel sticking and after-image lag
Displaying the same images such as still images for a long
time may cause after-image lagging. This may occur in the
following two cases.
1. After-image lagging due to remaining electric
load
When image patterns with very high peak luminance are
displayed more than 1 minute, after-image lagging may occur
due to the remaining electric load. The after-images remaining
on the screen will disappear when moving images are dis-
played. The time for the after-images to disappear depends on
the luminance of the still images and the time they had been
displayed.
2. After-image (lag image) due to burning
Avoid displaying the same image on the Plasma Display
continuously over a long period of time. If the same image is
displayed continuously for several hours, or for shorter periods
of time over several days, a permanent after-image may remain
on the screen due to burning of the fluorescent materials. Such
images may become less noticeable if moving images are later
displayed, but they will not disappear completely.
The Auto Power Off function can be set to help prevent
damage from screen burning (see page 38).
DO NOT PLACE THIS PRODUCT ON AN UNSTABLE CART,
STAND, TRIPOD, BRACKET, OR TABLE. THE PRODUCT MAY
FALL, CAUSING SERIOUS PERSONAL INJURY AND SERIOUS
DAMAGE TO THE PRODUCT. USE ONLY WITH A CART, STAND,
TRIPOD, BRACKET, OR TABLE RECOMMENDED BY THE
MANUFACTURER, OR SOLD WITH THE PRODUCT. FOLLOW
THE MANUFACTURE’S INSTRUCTIONS WHEN INSTALLING
THE PRODUCT AND USE MOUNTING ACCESSORIES RECOM-
MENDED BY THE MANUFACTURER.
A PRODUCT AND CART COMBINATION SHOULD BE MOVED
WITH THE CARE. QUICK STOPS, EXCESSIVE FORCE, AND
UNEVEN SURFACES MAY CAUSE THE PRODUCT AND CART
COMBINATION TO OVERTURN.
04-PDP42A3HD-Eng (05-10) 05.4.20, 4:30 PM7
02 Safety Precautions
8
En
Electricity is used to perform many useful functions, but it can
also cause personal injuries and property damage if improperly
handled. This product has been engineered and manufactured
with the highest priority on safety. However, improper use can
result in electric shock and/or fire. In order to prevent potential
danger, please observe the following instructions when install-
ing, operating and cleaning the product. To ensure your safety
and prolong the service life of your product, please read the
following precautions carefully before using the product.
1. Read instructions—All operating instructions must be read
and understood before the product is operated.
2. Keep this manual in a safe place—These safety and
operating instructions must be kept in a safe place for
future reference.
3. Observe warnings—All warnings on the product and in the
instructions must be observed closely.
4. Follow instructions—All operating instructions must be
followed.
5. Cleaning—Unplug the power cord from the AC outlet before
cleaning the product. To clean the product, use the supplied
cleaning cloth or other soft clothes (e.g., cotton, flannel).
6. Attachments—Do not use attachments not recommended
by the manufacturer. Use of inadequate attachments can
result in accidents.
7. Water and moisture—Do not use the product near water,
such as bathtub, washbasin, kitchen sink and laundry tub,
swimming pool and in a wet basement.
8. Stand—Do not place the product on an unstable cart,
stand, tripod or table. Placing the product on an unstable
base can cause the product to fall, resulting in serious
personal injuries as well as damage to the product. Use
only a cart, stand, tripod, bracket or table recommended by
the manufacturer or sold with the product. When mounting
the product on a wall, be sure to follow the manufacturer’s
instructions. Use only the mounting hardware recom-
mended by the manufacturer.
9. When relocating the product placed on a cart, it must be
moved with utmost care. Sudden stops, excessive force and
uneven floor surface can cause the product to fall from the
cart.
10. Ventilation—The vents and other openings in the cabinet
are designed for ventilation. Do not cover or block these
vents and openings since insufficient ventilation can cause
overheating and/or shorten the life of the product. Do not
place the product on a bed, sofa, rug or other similar
surface, since they can block ventilation openings. This
product is not designed for built-in installation; do not place
the product in an enclosed place such as a bookcase or
rack, unless proper ventilation is provided or the
manufacturer’s instructions are followed.
11. Power source—This product must operate on a power
source specified on the specification label. If you are not
sure of the type of power supply used in your home, consult
your dealer or local power company.
12. Power cord protection—The power cords must be routed
properly to prevent people from stepping on them or objects
from resting on them. Check the cords at the plugs and
product.
13. The plasma Display used in this product is made of glass.
Therefore, it can break when the product is dropped or
applied with impact. Be careful not to be injured by broken
glass pieces in case the plasma Display breaks.
14. Overloading—Do not overload AC outlets or extension
cords. Overloading can cause fire or electric shock.
15. Entering of objects and liquids—Never insert an object into
the product through vents or openings. High voltage flows
in the product, and inserting an object can cause electric
shock and/or short internal parts. For the same reason, do
not spill water or liquid on the product.
16. Servicing—Do not attempt to service the product yourself.
Removing covers can expose you to high voltage and other
dangerous conditions. Request a qualified service person to
perform servicing.
17. Repair—If any of the following conditions occurs, unplug
the power cord from the AC outlet, and request a qualified
service person to perform repairs.
a. When the power cord or plug is damaged.
b. When a liquid was spilled on the product or when
objects have fallen into the product.
c. When the product has been exposed to rain or water.
d. When the product does not operate properly as de-
scribed in the operating instructions.
Do not touch the controls other than those described in
the operating instructions. Improper adjustment of
controls not described in the instructions can cause
damage, which often requires extensive adjustment work
by a qualified technician.
e. When the product has been dropped or damaged.
f. When the product displays an abnormal condition. Any
noticeable abnormality in the product indicates that the
product needs servicing.
18. Replacement parts—In case the product needs replace-
ment parts, make sure that the service person uses replace-
ment parts specified by the manufacturer, or those with the
same characteristics and performance as the original parts.
Use of unauthorized parts can result in fire, electric shock
and/or other danger.
19. Safety checks—Upon completion of service or repair work,
request the service technician to perform safety checks to
ensure that the product is in proper operating condition.
20. Wall or ceiling mounting—When mounting the product on
a wall or ceiling, be sure to install the product according to
the method recommended by the manufacturer.
21. Heat sources—Keep the product away from heat sources
such as radiators, heaters, stoves and other heat- generat-
ing products (including amplifiers).
22. Unplug the power cord from the AC outlet before installing
the speakers.
23. Never expose the screen of the Plasma Display to a strong
impact, for example, by hitting it. The screen may be
broken, resulting in fire or personal injury.
24. Do not expose the Plasma Display to direct sunlight for a
long period of time. The optical characteristics of the front
protection panel changes, resulting in discoloration or
warp.
25. The Plasma Display weighs about 40.5 kg (89.3 lbs.) for the
PDP-42A3HD/PDP-4214HD. Because it has small depth and
is unstable, unpack, carry, and install the product with one
more person at least and use the handles.
02 Safety Precautions
04-PDP42A3HD-Eng (05-10) 05.4.20, 4:30 PM8
02Safety Precautions
English
9
En
Installation Precautions
Observe the following precautions when installing with any items such as the optional brackets.
When using the optional brackets or equivalent items
Ask your dealer to perform the installation.
Be sure to use the supplied bolts.
•For details, see the instruction manual that comes with the optional brackets (or equivalent items).
Rear view Side view
Be sure to use four mounting holes covered with rubber cap.
Use M6 screws, which go 10 mm (3/8 inches) in depth from the mounting surface of the Plasma Display. See the side view above.
Be careful not to block the ventilation opening at the rear of the Plasma Display.
Be sure to install the Plasma Display on a flat surface because it contains glass.
The screw holes other than the above are to be used only for the specified products. Never use them for mounting non-specified
products.
It is strongly recommended to use the optional PIONEER mounting products.
PIONEER shall not be liable for any personal injury or product damage that results from the use of mounting items other than the
optional PIONEER products.
Mounting holes covered with rubber cap
Mounting surface
Mounting bracket (or
equivalent item)
M6 screw
10 mm (3/8 inches)
Plasma
Display
04-PDP42A3HD-Eng (05-10) 05.4.20, 4:30 PM9
03 Supplied Accessories
10
En
Operating Instructions
Always use the power cord supplied with the Plasma Display.
Power cord
Remote control unit
03 Supplied Accessories
AAA size battery × 2
(Alkaline battery)
Warranty card Hook × 2
04-PDP42A3HD-Eng (05-10) 05.4.20, 4:30 PM10
04Part Names
English
11
En
Plasma Display
1 POWER button
2STANDBY indicator
3 Current input source indicators
4 Remote control sensor
5INPUT button
Front view
STAND
BY
/ON
STANDBY
/ON
POWER
POWER
DTV TV VCR DVD HDMI
STANDBY
DTV TV VCR DVD HDMI
STANDBY
5910
1
6
342
78
6OK button
7MENU button
8 VOLUME –/+ buttons
9 CHANNEL –/+ buttons
10 STANDBY/ON button
04 Part Names
05-PDP42A3HD-Eng (11-14) 05.4.20, 4:30 PM11
04 Part Names
12
En
Rear view
1 VIDEO 3 terminals (AUDIO/VIDEO/S-VIDEO)
2 DTV-ANTENNA IN terminal
3 ANTENNA/CABLE IN terminal
4 MONITOR OUT terminals (AUDIO/VIDEO)
5 DIGITAL OUT terminal
6 VIDEO 1/VIDEO 2 terminals (AUDIO/VIDEO/
S-VIDEO)
7 COMPONENT 1/COMPONENT 2 terminals
(COMPONENT VIDEO/AUDIO)
8 HDMI terminal (AUDIO/HDMI)
9 RS-232C terminal (service only)
10 AC IN terminal
1
234 8 9
10
6 7
INPUT
AUDIO
R
L
VIDEO 3
S-VIDEO 3
DTV-
ANTENNA IN
ANTENNA
/ CABLE IN
MONITOR OUT
VIDEO
VIDEO 1
L-AUDIO-R S-VIDEO 1
AUDI O
DIGITAL OUT
OPTICAL
R
L
HDMI
INPUT
SERVICE ONLY AC IN
AUDI OHDMI
R
L
VIDEO 2 L-AUDIO-R
L-AUDIO-R Y
L-AUDIO-R Y
C
B
/P
B
C
B
/P
B
C
R
/P
R
C
R
/P
R
COMPONENT 2
COMPONENT 1
S-VIDEO 2
5
05-PDP42A3HD-Eng (11-14) 05.4.20, 4:30 PM12
04Part Names
English
13
En
Remote control unit
SPLIT SPLIT P IN P SWAP
SPLIT SPLIT
DTV
SIGNAL MTS LIST
CH
DELETE
INPUT SHIFT
CH+ CH–
MUTING
VOLCH
C.C.
FAVORITE
CH
CH
RETURN
EXIT BACK
MENU
SLEEP
DISPLAY
SCREEN SIZESOUND EFFECT
HD WIDEINPUT
TV
AV SELECTION
11 3322
44 6655
77 9988
CH
ENTER
00
OK
1
2
3
4
5
6
8
9
10
11
12
13
14
15
16
19
20
21
22
17
18
7
1 HD WIDE: Adjusts the picture to fit the 16:9
wide aspect ratio. Available in DTV mode.
2INPUT: Displays all available input sources.
Press the c or d button to select the required
input source.
3AV SELECTION: Selects the picture mode
(Standard, Dynamic, Movie, Game or User).
4 SOUND EFFECT: Selects the sound effect
(Flat, Speech, Movie, Music or User).
5 0-9: Select the channel.
6 ÷ (dot): Selects the sub-channel of DTV.
7C.C.: Display captions while in the closed-
caption source.
8FAVORITE CH: Selects the favorite channel.
9 c/d/[/\: Controls the cursor in the on-
screen menu.
10 CH RETURN: Returns the selected channels.
11 EXIT: Exits from any display.
12 CH +/–: Changes the channel.
13
MUTING: Mutes the sound. To turn the
sound back on, press the MUTING, VOL + or
VOL – buttons.
14 TV
: Switches between operation and
standby mode.
15 SCREEN SIZE: Changes the aspect ratio of
the screen (Zoom/Cinema/Full/4:3/Wide).
16 CH ENTER: Enters channels.
17 SLEEP: Sets the sleep timer.
18 DISPLAY: Shows the display.
19 OK: Executes a command.
20 MENU: Displays the on-screen menu.
21 BACK: Returns to the previous menu screen.
22 VOL +/–: Sets the volume.
05-PDP42A3HD-Eng (11-14) 05.4.20, 4:30 PM13
04 Part Names
14
En
SPLIT SPLIT P IN P SWAP
SPLIT SPLIT
DTV
SIGNAL MTS LIST
FAVORITE
CH DELETE
INPUT SHIFT
CH+ CH–
MUTING
VOLCH
SPLIT SPLIT P IN P SWAP
SPLIT SPLIT
DTV
SIGNAL
MTS LIST
CH
DELETE
INPUT SHIFT
CH+ CH–
24
25
26
27
23
23 SPLIT Function Buttons
SPLIT: Selects the SPLIT mode (Off, PIP, Twin1
or Twin2).
SPLIT INPUT: Selects an input source for the
sub picture.
P IN P/SHIFT: Selects a position for the sub-
picture.
SWAP: Interchanges the main picture and
sub-picture.
SPLIT CH + SPLIT CH –: Changes the chan-
nel of the sub-picture.
24 DTV SIGNAL: Displays the signal strength
and quality.
25 MTS: Selects the sound mode.
26 CH DELETE: Deletes a channel.
27 LIST: Displays the channel list in Edit Channel
List. Press the c or d button to select the
required channel.
When using the remote control unit, point it at the Plasma Display.
Slide
05-PDP42A3HD-Eng (11-14) 05.4.20, 4:30 PM14
05Preparation
English
15
En
Installing the Plasma Display
Locating
Avoid direct sunlight. Maintain adequate ventilation.
Because the Plasma Display is heavy, be sure to have
someone help you when moving it.
If you place anything on the top of the Plasma Display it will not
receive enough ventilation and will not operate properly.
Allow enough space around the upper and back parts when
installing to ensure ventilation around the backside.
Operating Environment
Operating environment temperature and humidity: +0°C to
+40°C (+32°F to +104°F); less than 80% RH (cooling vents not
blocked)
Avoid installing at the following locations:
Under direct exposure to sunlight
Under strong artificial light
In high humidity
•Poorly ventilated
Preventing the Plasma Display from
Falling Over
Be sure to take special care to ensure that the Plasma
Display will not fall over.
Using a wall for stabilization
1
Attach the supplied falling prevention bolts (hooks) to the
Plasma Display.
2
Use storing cords or chains to stabilize the Plasma
Display appropriately and firmly to a wall, pillar, or other
study element.
•Perform this work in the same way for both the left and
right sides.
Use ropes, chains and fittings that are available on the
market.
•A table or an area of the floor with adequate strength should
always be used to support the Plasma Display. Failure to do
so could result in personal injury and physical damage.
When installing the Plasma Display, please take the neces-
sary safety measures to prevent it from falling or overturning
in case of emergencies, such as earthquakes, or of acci-
dents.
If you do not take these precautions, the Plasma Display
could fall down and cause injury.
The screws, hooks, chains and other fittings that you use to
secure the Plasma Display to prevent it from overturning will
vary according to the composition and thickness of the
surface to which it will be attached.
Select the appropriate screws, hooks, chains and other
fittings after first inspecting the surface carefully to deter-
mine its thickness and composition and after consulting a
professional installer if necessary.
05 Preparation
Over 10
cm (3
15
/
16
inches)
Over 50 cm (19
11
/16 inches)
1 Hook
2 Cord or chain
3 Fitting
06-PDP42A3HD-Eng (15-18) 05.4.20, 4:30 PM15
05 Preparation
16
En
Preparing the remote control unit
Inserting batteries
1
Open the battery cover.
2
Insert the supplied two AAA (1.5 V) size batteries.
The battery polarities must correspond with the (+) and
(–) indicators in the battery compartment.
3
Close the battery cover.
Cautions regarding batteries
The remote control unit cannot operate the system if the
batteries in the unit are empty. When this happens, replace
the batteries with new ones.
Do not use manganese batteries. When you replace the
batteries, use alkaline ones.
Do not mix batteries of different types. Different types of
batteries have different characteristics.
Do not mix old and new batteries. Mixing old and new
batteries can shorten the life of new batteries or cause
chemical leakage in old batteries.
• Do not leave dead batteries in the remote control unit;
chemical leakage will occur. If you find any chemical leakage,
wipe thoroughly with a cloth.
• The batteries supplied with this product may have a shorter
life expectancy due to storage conditions.
• If you will not use the remote control unit for an extended
period of time, remove the batteries from it.
WHEN DISPOSING OF USED BATTERIES, BE SURE
TO COMPLY WITH GOVERNMENT REGULATIONS
AND ENVIRONMENTAL PROTECTION GUIDELINES
THAT APPLY IN YOUR COUNTRY OR AREA.
Allowed operation range of the remote control
unit
Operate the remote control unit while pointing it toward the
remote control sensor located at the bottom center of the front
panel of the Plasma Display. The distance from the remote
control sensor must be within 7 m (23 feet) and the angle
relative to the sensor must be within 30 degrees in the right or
left direction.
S
TA
N
D
B
Y
/O
N
P
O
W
E
R
D
T
V
T
V
V
C
R
D
V
D
H
D
M
I
S
T
A
N
D
B
Y
30°
Remote control
sensor
7 m (23 feet)
30°
06-PDP42A3HD-Eng (15-18) 05.4.20, 4:30 PM16
05Preparation
English
17
En
Cautions regarding the remote control unit
Do not expose the remote control unit to shock, liquid, or
high humidity.
Do not place the remote control unit under direct sunlight;
the unit may deform.
The remote control unit may not work properly if the remote
sensor window of the Plasma Display is under direct sunlight
or strong lighting. In such case, change the angle of the
lighting or Plasma Display, or operate the remote control unit
closer to the remote sensor window.
When any obstacle exists between the remote control unit
and the remote control sensor, the remote control unit may
not function.
As the batteries become empty, the remote control unit can
function within a shorter distance from the remote control
sensor. Replace the batteries with new ones if necessary.
The Plasma Display emits very weak infrared rays from its
screen. If you place such equipment operated through
infrared remote control as a VCR nearby, that equipment may
not receive commands from its remote control unit properly
or entirely. If this is the case, place that equipment at a
location far enough from the Plasma Display.
Depending on the installation environment, infrared rays
from the Plasma Display may not allow this system to
properly receive commands from the remote control unit or
may shorten allowable distances between the remote control
unit and the remote control sensor. The strength of infrared
rays emitted from the screen differs, depending on images
displayed on the screen.
Cable connections for watching digital
and/or conventional TV channels
This system is equipped with two terminals for inputting TV
broadcasting signals: ANTENNA/CABLE IN and DTV-ANTENNA
IN. The ANTENNA/CABLE IN terminal accepts conventional TV
broadcasting signals. The DTV-ANTENNA IN terminal accepts
digital TV broadcasting signals. When using a cable TV to
watch conventional TV channels, connect to the ANTENNA/
CABLE IN terminal as shown.
Connecting to an Aerial
To view TV channels correctly, the Plasma Display must receive
a signal.
Connecting the aerial of digital TV
When you connect the aerial of digital TV, connect the outdoor
aerial.
DTV-
ANTENNA IN
Connecting the aerial of analog TV
There are three ways to connect the aerial or network input
cable for analog TV.
It is recommended to connect the outdoor aerial for the best
outcome of the images.
Cable
Converter
ANTENNA
/ CABLE IN
Cable TV
06-PDP42A3HD-Eng (15-18) 05.4.20, 4:30 PM17
05 Preparation
18
En
Power cord
Connecting the power cord
Connect the power cord after all component connections are completed.
Plasma Display (rear view)
DTV-
ANTENNA IN
ANTENNA
/ CABLE IN
MONITOR OUT
VIDEO
VIDEO 1
L-AUDIO-R S-VIDEO 1
AUDI O
DIGITAL OUT
OPTICAL
R
L
HDMI
INPUT
SERVICE ONLY AC IN
AUDI OHDMI
R
L
VIDEO 2 L-AUDIO-R
L-AUDIO-R Y
L-AUDIO-R Y
CB/PB
CB/PB
CR/PR
CR/PR
COMPONENT 2
COMPONENT 1
S-VIDEO 2
Use only the supplied power cord.
Be sure to use the specified power supply voltage;
neglecting this can result in fire or electric shock.
•For the Plasma Display, a three-core power cord with a
ground terminal is used for efficiency protection.
Always connect the power cord to a three-pronged
outlet and make sure that the cord is properly grounded.
Always turn off the power of the Plasma Display when connecting
the power cord.
Disconnect the power cord from the power outlet when the Plasma
Display is not going to be used for a long period of time.
06-PDP42A3HD-Eng (15-18) 05.4.20, 4:30 PM18
06Basic Operations
English
19
En
Turning the power on and off (Standby)
1
Press the POWER button on the bottom of the Plasma
Display to enter the standby mode.
The STANDBY indicator lights up.
2
Press the TV button on the remote control or the
STANDBY/ ON button on the bottom of the Plasma
Display.
The Plasma Display switches to on. The STANDBY
indicator lights off and the current input source
indicator lights up.
3
To switch the Plasma Display off, press the TV button
on the remote control or the STANDBY/ ON button on
the bottom of the Plasma Display.
The Plasma Display enters to standby mode and the
STANDBY indicator lights up instead of the current
input source indicator.
4
To switch the Plasma Display off completely, press the
POWER button on the bottom of the Plasma Display.
The STANDBY indicator lights off.
If you are not going you use the Plasma Display for a long period of
time, press POWER button on the bottom of the Plasma Display
to switch the Plasma Display off completely and disconnect the
power cord of the Plasma Display from a wall outlet.
If the Plasma Display is switched off completely, you cannot turn the
Plasma Display on by pressing the TV button on the remote
control.
If the Plasma Display is switched off completely, it cannot switch the
Plasma Display on automatically by the “On Timer“ setting.
06 Basic Operations
POWER
DTV TV VCR DVD HDMI
STANDBY
STANDBY
/ON
DTV TV VCR DVD HDMI
STANDBY
POWER
button
STANDBY indicator
STANDBY/ON button
Current input source indicator
07-PDP42A3HD-Eng (19-23) 05.4.20, 4:30 PM19
06 Basic Operations
20
En
Watching TV channels
Unless you set up TV channels that you can watch under the
current conditions, you cannot tune in those channels. For the
procedure, see “Setting up TV channels” on page 25.
When watching a digital TV program, you may see emergency alert
messages scrolling at the top of the screen. Those messages are
broadcast by TV stations as necessary when in emergency situations.
Selecting the analog and digital channels
You can select the input mode between analog and digital
channels by pressing the INPUT button.
When you switch the input mode, the last channel you previously
selected will be received.
Changing channels
To increase the channel number, press the CH + button on the
remote control unit. To decrease the channel number, press the
CH – button .
CHANNEL +/– on the Plasma Display has the same
function as
CH +/– on the remote control unit.
Using 0 – 9 on the remote control unit
Select channels directly by pressing buttons 0 to 9.
EXAMPLE
•To select channel 5 (1-digit channel), press 5.
•To select channel 25 (2-digit channel), press 2 then 5.
•To select channel 125 (3-digit channel), press 1, 2, then 5.
•To select subchannel 10-01, press 1, 0, •(dot), 0, then 1.
•Pressing the CH ENTER button after entering the channel number,
enables you select channels quickly.
•To return to the previous channel, press the CH RETURN button.
MUTING
VOLCH
C.C.
FAVORITE
CH
CH
RETURN
EXIT BACK
MENU
SLEEP
DISPLAY
SCREEN SIZESOUND EFFECT
HD WIDEINPUT
TV
AV SELECTION
11 3322
44 6655
77 9988
CH
ENTER
00
OK
07-PDP42A3HD-Eng (19-23) 05.4.20, 4:30 PM20
1 / 1

Pioneer PDP-42A3HD User manual

Category
LCD TVs
Type
User manual

Ask a question and I''ll find the answer in the document

Finding information in a document is now easier with AI

Ask the document