Pioneer PDP-4214HD User manual

PLASMA DISPLAY SYSTEM

SYSTEME D’ÉCRAN PLASMA

SISTEMA DE PANTALLA DE PLASMA

PDP-42A3HD

PDP-4214HD

Operating Instructions

Mode d’emploi

Manual de instrucciones

Register Your Product at

www.pioneerelectronics.com (US)

www.pioneerelectronics.ca (Canada)

01-PDP42A3HD-Eng (Cover) 5/17/05, 7:12 PM1

Read these instructions.

Keep these instructions.

Heed all warnings.

Follow all instructions.

Do not use this apparatus near water.

Clean only with dry cloth.

Do not block any ventilation openings. Install in

accordance with the manufacturer’s instructions.

Do not install near any heat sources such as

radiators, heat registers, stoves, or other apparatus

(including amplifiers) that produce heat.

Do not defeat the safety purpose of the polarized or

grounding-type plug. A polarized plug has two

blades with one wider than the other. A grounding

type plug has two blades and a third grounding

prong. The wide blade or the third prong are

provided for your safety. If the provided plug does

not fit into your outlet, consult an electrician for

replacement of the obsolete outlet.

Protect the power cord from being walked on or

pinched particularly at plugs, convenience

receptacles, and the point where they exit from the

apparatus.

1)

2)

3)

4)

5)

6)

7)

8)

9)

10)

Only use attachments/accessories specified by the

manufacturer.

Use only with the cart, stand, tripod, bracket, or

table specified by the manufacturer, or sold with the

apparatus. When a cart is used, use caution when

moving the cart/apparatus combination to avoid

injury from tip-over.

Unplug this apparatus during lightning storms or

when unused for long periods of time.

Refer all servicing to qualified service personnel.

Servicing is required when the apparatus has been

damaged in any way, such as power-supply cord or

plug is damaged, liquid has been spilled or objects

have fallen into the apparatus, the apparatus has

been exposed to rain or moisture, does not operate

normally, or has been dropped.

11)

12)

13)

14)

Note to CATV system installer.

This reminder is provided to call the CATV system installer’s attention to Article 820-40 of the NEC that provides

guidelines for proper grounding and, in particular, specifies that the cable ground–shall be connected to the

grounding system of the building, as close to the point of cable entry as practical.

02-PDP42A3HD-Eng (02-03) 5/17/05, 7:12 PM2

English

WARNING: THE APPARATUS IS NOT WATER-

PROOFS, TO PREVENT FIRE OR SHOCK HAZARD, DO

NOT EXPOSE THIS APPLIANCE TO RAIN OR MOISTURE

AND DO NOT PUT ANY WATER SOURCE NEAR THIS

APPARATUS, SUCH AS VASE, FLOWER POT, COSMET-

ICS CONTAINER AND MEDICINE BOTTLE ETC.

WARNING: Handling the cord on this product or

cords associated with accessories sold with the prod-

uct will expose you to lead, a chemical known to the

State of California and other governmental entities to

cause cancer and birth defects or other reproductive

harm. Wash hands after handling.

NOTE: This equipment has been tested and found to

comply with the limits for a class B digital device, pur-

suant to Part 15 of the FCC Rules. These limits are de-

signed to provide reasonable protection against harm-

ful interference in a residential installation. This equip-

ment generates, uses, and can radiate radio frequency

energy and, if not installed and used in accordance with

the instructions, may cause harmful interference to ra-

dio communications. However, there is no guarantee that

interference will not occur in a particular installation. If

this equipment does cause harmful interference to ra-

dio or television reception, which can be determined by

turning the equipment off and on, the user is encour-

aged to try to correct the interference by one or more of

the following measures:

— Reorient or relocate the receiving antenna.

— Increase the separation between the equipment and

receiver.

— Connect the equipment into an outlet on a circuit

different from that to which the receiver is connected.

— Consult the dealer or an experienced radio/TV tech-

nician for help.

Information to User

Alteration or modifications carried out without appro-

priate authorization may invalidate the user’s right to

operate the equipment.

[For Canadian model]

This Class B digital apparatus complies with Canadian

ICES-003.

CAUTION:

This product satisfies FCC regulations when shielded

cables and connectors are used to connect the unit to

other equipment. To prevent electromagnetic interfer-

ence with electric appliances such as radios and televi-

sions, use shielded cables and connectors for connec-

tions.

IMPORTANT NOTICE: The serial number for this

equipment is located on the rear panel. Please write

this serial number on your enclosed warranty card and

keep it in a secure area. This is for your security.

WARNING: Be sure to plug this equipment into a

grounding-type AC outlet.

02-PDP42A3HD-Eng (02-03) 5/17/05, 7:12 PM3

4

En

Contents

Thank you for buying this Pioneer product.

Please read through these operating instructions so you will know how to operate your model properly. After you have finished

reading the instructions, put them away in a safe place for future reference.

In some countries or regions, the shape of the power plug and power outlet may sometimes differ from that shown in the explana-

tory drawings. However the method of connecting and operating the unit is the same.

01 Important User Guidance Information

02 Safety Precautions

03 Supplied Accessories

04 Part Names

Plasma Display ................................................................... 10

Remote control unit ............................................................ 12

05 Preparation

Installing the Plasma Display ............................................ 14

Preventing the Plasma Display from Falling Over ........... 14

Preparing the remote control unit ..................................... 15

Inserting batteries ......................................................... 15

Cautions regarding batteries ....................................... 15

Allowed operation range of

the remote control unit .............................................. 15

Cautions regarding the remote control unit .............. 16

Cable connections for watching digital and/or conventional

TV channels ....................................................................... 16

Connecting to an Aerial ............................................... 16

Connecting the power cord ............................................... 17

06 Basic Operations

Turning the power on and off (Standby) ........................... 18

Watching TV channels........................................................ 19

Selecting the analog and digital channels ................. 19

Changing channels ...................................................... 19

Changing the volume and sound ................................ 20

Displaying Information ....................................................... 20

Setting MTS/SAP mode ...................................................... 21

Changing the language ............................................... 21

Using the multiscreen functions ....................................... 21

07 Menu Setup

Menu configuration ............................................................ 23

Menu operations ................................................................. 23

08 Tuner Setup

Setting up TV channels ...................................................... 24

Scanning Channels Automatically ............................. 24

Scanning Analog Channels Manually ........................ 24

Scanning Digital Channels Manually ......................... 25

Editing Channel List ..................................................... 25

Display the Channel List .............................................. 26

Setting up the Parental Control ......................................... 26

Activating the Parental Control ......................................... 27

Setting the voluntary movie rating

system (MPAA) ................................................................. 27

Setting the TV Ratings .................................................. 28

Setting up the Canadian rating systems .................... 28

Blocking No rating programs ...................................... 29

Viewing Closed Caption Information................................. 29

Setting the Current Date and Time ................................... 30

09 Adjustments and Settings

Sleep Timer .......................................................................... 31

Picture adjustments ........................................................... 31

Selecting the Picture Mode ......................................... 31

Customizing the Picture Settings ............................... 32

Using the Noise Reduction Feature ............................ 32

Setting the Color Temperature .................................... 33

Selecting the Sound Effect ................................................ 33

Customizing the Sound Settings ....................................... 34

Adjusting the Volume Automatically ................................. 34

Setting the Surround Sound .............................................. 34

Setting up External Digital Sound ..................................... 34

Changing the Screen Size .................................................. 35

Viewing the Input Source ................................................... 35

Setting for the language of on-screen display ................. 35

Setting for the prior audio language of digital TV ............ 36

Screen Saver ....................................................................... 36

Setting the Full White mode ........................................ 36

Power Control ...................................................................... 37

Switching the Plasma Display Off Automatically ...... 37

Setting the Plasma Display On Time .......................... 37

Setting the Plasma Display Off Time .......................... 37

10 Enjoying through External Equipment

Connecting to the External Input ...................................... 38

Connecting to the Component Input ................................ 39

Connecting to the HDMI Input .......................................... 40

Connecting to the Monitor Output .................................... 40

Connecting to the DIGITAL Audio Output ......................... 41

11 Appendix

Troubleshooting .................................................................. 42

Specifications ...................................................................... 44

03-PDP42A3HD-Eng (04) 5/17/05, 7:12 PM4

01Important User Guidance Information

English

5

En

In order to obtain maximum enjoyment from this Pioneer

PureVision PDP-42A3HD/PDP-4214HD Plasma Display System,

please first read this information carefully.

With the Pioneer PureVision PDP-42A3HD/PDP-4214HD, you

can be assured of a high quality Plasma Display System with

long-life and high reliability. To achieve images of exceptional

quality, this Pioneer Plasma Display System incorporates state-

of-the-art design and construction, as well as very precise and

highly advanced technology.

Over the course of its lifetime, the luminosity of the Pioneer

PDP-42A3HD/PDP-4214HD Plasma Display System will

diminish very slowly, such as with all phosphor-based screens

(for example, a traditional tube-type television). To enjoy

beautiful and bright images on your Pioneer Plasma Display

System for many years to come, please carefully read and

follow the usage guidelines below.

Usage guidelines

All phosphor-based screens (including conventional tube-type

televisions) can be affected by displaying static images for a

prolonged period. Plasma Display Systems are no exception to

this rule. After-image and permanent effects on the screen can

be avoided by taking some basic precautions. By following the

recommendations listed below, you can ensure longer and

satisfactory results from your plasma:

• Whenever possible, avoid frequently displaying the same

image or virtually still moving pictures (e.g. closed-captioned

images or video game images which have static portions).

• Avoid viewing the On Screen Display for extended periods,

from a DVD player, VCR, and all other components.

• Do not leave the same picture freeze-framed or paused

continuously over a long period of time, when using the still

picture mode from a TV, VCR, DVD player or any other

component.

• Images which have both very bright areas and very dark

areas side by side should not be displayed for a prolonged

period of time.

• When playing a game, the “Game” mode setting within “AV

Selection” is strongly recommended. However, please limit its

use to less than 2 hours at a time.

•After playing a game, or any still image, it is best to view a

normal moving picture in the “Wide” or “Full” screen setting

for over 3 times longer than the previous still/moving image.

•After using the Plasma Display System, always switch the

display to “STANDBY” mode.

Installation guidelines

The Pioneer PureVision PDP-42A3HD/PDP-4214HD Plasma

Display System incorporates a very thin design. To ensure

safety, please take the proper measures to mount or install the

Plasma Display, in order to prevent the unit from tipping over in

the event of vibration or accidental movement.

This product should be installed by using only parts and

accessories designed by PIONEER. Use of accessories other

than the PIONEER installation bracket may result in instability,

and could cause injury. For custom installation, please consult

the dealer where the unit was purchased. To ensure correct

installation, experienced and qualified experts must install the

unit. PIONEER will not be held responsible for accident or

damage caused by the use of parts and accessories manufac-

tured by other companies.

To avoid malfunction and overheating when installing, make

sure that the vents on the main unit are not blocked. To ensure

proper heat emission:

• Distance the unit slightly from other equipment, walls, etc.

For the minimum space required around the unit, see page

14.

• Do not fit the unit inside narrow spaces where ventilation is

poor.

• Do not cover with a cloth, etc.

• Clean the vents on the sides and rear of the unit to remove

dust build-up by using a vacuum cleaner set to its lowest

suction setting.

• Do not place the product on a carpet or blanket.

• Do not reverse the product.

Using the unit without proper ventilation may cause the

internal temperature to rise, and could result in possible

malfunction. When the surrounding or internal temperature

exceeds a certain degree, the display will automatically power

off in order to cool the internal electronics and prevent a

hazardous occurrence.

Malfunction can be caused by many factors: inappropriate

installation site, improper assembly/installation/mounting,

improper operation of or modifications made to this product.

However, PIONEER cannot be held responsible for accidents or

malfunction caused by the above.

The following are typical effects and characteristics of a

phosphor-based matrix display and as such, are not covered by

the manufacturer’s limited warranties:

•Permanent residual images upon the phosphors of the panel.

• The existence of a minute number of inactive light cells.

•Panel generated sounds, examples: Fan motor noise, and

electrical circuit humming / glass panel buzzing.

01 Important User Guidance Information

04-PDP42A3HD-Eng (05-9) 5/17/05, 7:12 PM5

01 Important User Guidance Information

6

En

PIONEER bears no responsibility for any damages arising from

incorrect use of the product by you or other people, malfunc-

tions when in use, other product related problems, and use of

the product except in cases where the company must be liable.

Information of pixel defect

Plasma Display systems display images consisting of hundreds

of thousands of minute pixels (light emitting cells), and there is

a possibility of inactive, flashing or continually illuminated

pixels.

Infrared rays

The Plasma Display releases infrared rays because of its

characteristics. Depending on how the Plasma Display is in

use, the remote controls of nearby equipment may be adversely

affected or wireless headphones using infrared rays are

interfered by noise. If this is the case, place that equipment at a

location where its remote control sensor is not affected.

Radio interference

While this product meets the required specifications, it emits a

small amount of noise. If you place such equipment as an AM

radio, personal computer, and VCR close to this product, that

equipment may be interfered. If this happens, place that

equipment far enough from this product.

Plasma Display driving sound

The screen of the Plasma Display is composed of extremely fine

pixels and these pixels emit light according to received video

signals. This principle may make you hear buzz sound electrical

circuit hamming from the Plasma Display.

Also note that the rotation speed of the cooling fan motor

increases when the ambient temperature of the product

becomes high. You may hear the sound of the fan motor at that

time.

Do not attach such items as labels and tape to the

product

• This may result in the discoloration or scratch of the cabinet.

When not using the product for a long period of time

• If you do not use the product for a long period of time, the

functions of the product may be adversely affected. Switch on

and run the product occasionally.

Condensation

• Condensation may take place on the surface or inside of the

product when the product is rapidly moved from a cold place

to a warm place or just after a heater is switched on in winter

morning, for example. When condensation takes place, do

not switch on the product and wait until condensation

disappears. Using the product with condensation may result

in malfunction.

Cleaning the screen

• When cleaning the screen of this product, gently wipe it with

a soft dry cloth; the supplied cleaning cloth or other similar

cloths (e.g., cotton and flannel). If you use a hard cloth or rub

the screen hard, the surface of the screen will be scratched.

• If you clean the surface of the screen with a wet cloth, water

droplets on the surface may enter into the product, resulting

in malfunction.

Cleaning the cabinet

• When cleaning the cabinet of this product, gently wipe it with

a soft dry cloth; the supplied cleaning cloth or other similar

cloths (e.g., cotton and flannel). If you use a hard cloth or rub

the cabinet hard, the surface of the cabinet will be scratched.

• The cabinet of this product is mostly composed of plastic. Do

not use chemicals such as benzine or thinner to clean the

cabinet. Using these chemicals may result in quality deterio-

ration or coating removal.

• Do not expose the product to volatile gas or fluid such as

pesticide. Do not make the product contact with rubber or

vinyl products for a long period of time. The effect of plasti-

cizer in the plastic may result in quality deterioration or

coating removal.

• If you clean the surface of the cabinet with a wet cloth, water

droplets on the surface may enter into the product, resulting

in malfunction.

Handles at the rear of the Plasma Display

• Do not remove the handles from the rear of the Plasma

Display.

• When moving the Plasma Display, ask another person for

help and use the handles attached to the rear of the Plasma

Display. Do not move the Plasma Display by holding only a

single handle. Use the handles as shown.

• Do not use the handles to hang the product when installing

or carrying the product, for example. Do not use the handles

for the purpose of preventing the product from tilting over.

04-PDP42A3HD-Eng (05-9) 5/17/05, 7:12 PM6

01Important User Guidance Information

English

7

En

Panel sticking and after-image lag

• Displaying the same images such as still images for a long

time may cause after-image lagging. This may occur in the

following two cases.

1. After-image lagging due to remaining electric

load

When image patterns with very high peak luminance are

displayed more than 1 minute, after-image lagging may occur

due to the remaining electric load. The after-images remaining

on the screen will disappear when moving images are dis-

played. The time for the after-images to disappear depends on

the luminance of the still images and the time they had been

displayed.

2. After-image (lag image) due to burning

Avoid displaying the same image on the Plasma Display

continuously over a long period of time. If the same image is

displayed continuously for several hours, or for shorter periods

of time over several days, a permanent after-image may remain

on the screen due to burning of the fluorescent materials. Such

images may become less noticeable if moving images are later

displayed, but they will not disappear completely.

• The Auto Power Off function can be set to help prevent

damage from screen burning (see page 37).

DO NOT PLACE THIS PRODUCT ON AN UNSTABLE CART,

STAND, TRIPOD, BRACKET, OR TABLE. THE PRODUCT MAY

FALL, CAUSING SERIOUS PERSONAL INJURY AND SERIOUS

DAMAGE TO THE PRODUCT. USE ONLY WITH A CART, STAND,

TRIPOD, BRACKET, OR TABLE RECOMMENDED BY THE

MANUFACTURER, OR SOLD WITH THE PRODUCT. FOLLOW

THE MANUFACTURE’S INSTRUCTIONS WHEN INSTALLING

THE PRODUCT AND USE MOUNTING ACCESSORIES RECOM-

MENDED BY THE MANUFACTURER.

A PRODUCT AND CART COMBINATION SHOULD BE MOVED

WITH THE CARE. QUICK STOPS, EXCESSIVE FORCE, AND

UNEVEN SURFACES MAY CAUSE THE PRODUCT AND CART

COMBINATION TO OVERTURN.

04-PDP42A3HD-Eng (05-9) 5/17/05, 7:12 PM7

02 Safety Precautions

8

En

Electricity is used to perform many useful functions, but it can

also cause personal injuries and property damage if improperly

handled. This product has been engineered and manufactured

with the highest priority on safety. However, improper use can

result in electric shock and/or fire. In order to prevent potential

danger, please observe the following instructions when install-

ing, operating and cleaning the product. To ensure your safety

and prolong the service life of your product, please read the

following precautions carefully before using the product.

1. Read instructions—All operating instructions must be read

and understood before the product is operated.

2. Keep this manual in a safe place—These safety and

operating instructions must be kept in a safe place for

future reference.

3. Observe warnings—All warnings on the product and in the

instructions must be observed closely.

4. Follow instructions—All operating instructions must be

followed.

5. Cleaning—Unplug the power cord from the AC outlet before

cleaning the product. To clean the product, use the supplied

cleaning cloth or other soft clothes (e.g., cotton, flannel). Do

not use liquid cleaners or aerosol cleaners.

6. Attachments—Do not use attachments not recommended

by the manufacturer. Use of inadequate attachments can

result in accidents.

7. Water and moisture—Do not use the product near water,

such as bathtub, washbasin, kitchen sink and laundry tub,

swimming pool and in a wet basement.

8. Stand—Do not place the product on an unstable cart,

stand, tripod or table. Placing the product on an unstable

base can cause the product to fall, resulting in serious

personal injuries as well as damage to the product. Use

only a cart, stand, tripod, bracket or table recommended by

the manufacturer or sold with the product. When mounting

the product on a wall, be sure to follow the manufacturer’s

instructions. Use only the mounting hardware recom-

mended by the manufacturer.

9. When relocating the product placed on a cart, it must be

moved with utmost care. Sudden stops, excessive force and

uneven floor surface can cause the product to fall from the

cart.

10. Ventilation—The vents and other openings in the cabinet

are designed for ventilation. Do not cover or block these

vents and openings since insufficient ventilation can cause

overheating and/or shorten the life of the product. Do not

place the product on a bed, sofa, rug or other similar

surface, since they can block ventilation openings. This

product is not designed for built-in installation; do not place

the product in an enclosed place such as a bookcase or

rack, unless proper ventilation is provided or the

manufacturer’s instructions are followed.

11. Power source—This product must operate on a power

source specified on the specification label. If you are not

sure of the type of power supply used in your home, consult

your dealer or local power company.

12. Power cord protection—The power cords must be routed

properly to prevent people from stepping on them or objects

from resting on them. Check the cords at the plugs and

product.

13. The plasma Display used in this product is made of glass.

Therefore, it can break when the product is dropped or

applied with impact. Be careful not to be injured by broken

glass pieces in case the plasma Display breaks.

14. Overloading—Do not overload AC outlets or extension

cords. Overloading can cause fire or electric shock.

15. Entering of objects and liquids—Never insert an object into

the product through vents or openings. High voltage flows

in the product, and inserting an object can cause electric

shock and/or short internal parts. For the same reason, do

not spill water or liquid on the product.

16. Servicing—Do not attempt to service the product yourself.

Removing covers can expose you to high voltage and other

dangerous conditions. Request a qualified service person to

perform servicing.

17. Repair—If any of the following conditions occurs, unplug

the power cord from the AC outlet, and request a qualified

service person to perform repairs.

a. When the power cord or plug is damaged.

b. When a liquid was spilled on the product or when

objects have fallen into the product.

c. When the product has been exposed to rain or water.

d. When the product does not operate properly as de-

scribed in the operating instructions.

Do not touch the controls other than those described in

the operating instructions. Improper adjustment of

controls not described in the instructions can cause

damage, which often requires extensive adjustment work

by a qualified technician.

e. When the product has been dropped or damaged.

f. When the product displays an abnormal condition. Any

noticeable abnormality in the product indicates that the

product needs servicing.

18. Replacement parts—In case the product needs replace-

ment parts, make sure that the service person uses replace-

ment parts specified by the manufacturer, or those with the

same characteristics and performance as the original parts.

Use of unauthorized parts can result in fire, electric shock

and/or other danger.

19. Safety checks—Upon completion of service or repair work,

request the service technician to perform safety checks to

ensure that the product is in proper operating condition.

20. Wall or ceiling mounting—When mounting the product on

a wall or ceiling, be sure to install the product according to

the method recommended by the manufacturer.

21. Heat sources—Keep the product away from heat sources

such as radiators, heaters, stoves and other heat- generat-

ing products (including amplifiers).

22. Unplug the power cord from the AC outlet before installing

the speakers.

23. Never expose the screen of the Plasma Display to a strong

impact, for example, by hitting it. The screen may be

broken, resulting in fire or personal injury.

24. Do not expose the Plasma Display to direct sunlight for a

long period of time. The optical characteristics of the front

protection panel changes, resulting in discoloration or

warp.

25. The Plasma Display weighs about 40.5 kg (89.3 lbs.) for the

PDP-42A3HD/PDP-4214HD. Because it has small depth and

is unstable, unpack, carry, and install the product with one

more person at least and use the handles.

02 Safety Precautions

04-PDP42A3HD-Eng (05-9) 5/17/05, 7:12 PM8

03Supplied Accessories

English

9

En

Operating Instructions

• Always use the power cord supplied with the Plasma Display.

Power cord

Remote control unit

03 Supplied Accessories

AAA size battery × 2

(Alkaline battery)

Warranty card

Hook × 2 Cleaning cloth

04-PDP42A3HD-Eng (05-9) 5/17/05, 7:12 PM9

04 Part Names

10

En

Plasma Display

1 POWER button

2STANDBY indicator

3 Current input source indicators

4 Remote control sensor

5INPUT button

Front view

STANDBY

/ON

STANDBY

/ON

POWER

DTV TV VCR DVD HDMI

STANDBY

DTV TV VCR DVD HDMI

STANDBY

5910

1

6

342

78

6OK button

7MENU button

8 VOLUME –/+ buttons

9 CHANNEL –/+ buttons

10 STANDBY/ON button

04 Part Names

05-PDP42A3HD-Eng (10-13) 5/17/05, 7:12 PM10

04Part Names

English

11

En

Rear view

1 VIDEO 3 terminals (AUDIO/VIDEO/S-VIDEO)

2 DTV-ANTENNA IN terminal

3 ANTENNA/CABLE IN terminal

4 MONITOR OUT terminals (AUDIO/VIDEO)

5 DIGITAL OUT terminal (OPTICAL)

6 VIDEO 1/VIDEO 2 terminals (AUDIO/VIDEO/

S-VIDEO)

7 COMPONENT 1/COMPONENT 2 terminals

(COMPONENT VIDEO/AUDIO)

8 HDMI terminal (AUDIO/HDMI)

9 RS-232C terminal (service only)

10 AC IN terminal

1

INPUT

AUDIO

R

L

VIDEO 3

S-VIDEO 3

234 8 9

10

6 7

DTV-

ANTENNA IN

ANTENNA

/ CABLE IN

MONITOR OUT

VIDEO

VIDEO 1

L-AUDIO-R S-VIDEO 1

AUDI O

DIGITAL OUT

OPTICAL

R

L

HDMI

INPUT

SERVICE ONLY AC IN

AUDI OHDMI

R

L

VIDEO 2 L-AUDIO-R

L-AUDIO-R Y

CB/PB

CR/PR

COMPONENT 2

COMPONENT 1

S-VIDEO 2

5

The terminals have faced downward.

05-PDP42A3HD-Eng (10-13) 5/17/05, 7:12 PM11

04 Part Names

12

En

Remote control unit

SPLIT SPLIT P IN P SWAP

SPLIT SPLIT

DTV

SIGNAL MTS LIST

CH

DELETE

INPUT SHIFT

CH+ CH–

MUTING

VOLCH

C.C.

FAVORITE

CH

RETURN

EXIT BACK

MENU

SLEEP

DISPLAY

SCREEN SIZESOUND EFFECT

HD WIDEINPUT

TV

AV SELECTION

11 3322

44 6655

77 9988

CH

ENTER

00

OK

1

2

3

4

5

6

8

9

10

11

12

13

14

15

16

19

20

21

22

17

18

7

1 HD WIDE: Adjusts the picture to fit the 16:9

wide aspect ratio. Available in DTV mode.

2INPUT: Displays all available input sources.

Press the c or d button to select the required

input source.

3AV SELECTION: Selects the picture mode

(Standard, Dynamic, Movie, Game or User).

4 SOUND EFFECT: Selects the sound effect

(Flat, Speech, Movie, Music or User).

5 0-9: Select the channel.

6 ÷ (dot): Selects the sub-channel of DTV.

7C.C.: Display captions while in the closed-

caption source.

8FAVORITE CH: Selects the favorite channel.

9 c/d/[/\: Controls the cursor in the on-

screen menu.

10 CH RETURN: Returns the selected channels.

11 EXIT: Exits from any display.

12 CH +/–: Changes the channel.

13

MUTING: Mutes the sound. To turn the

sound back on, press the MUTING, VOL + or

VOL – buttons.

14 TV

: Switches between operation and

standby mode.

15 SCREEN SIZE: Changes the aspect ratio of

the screen (Zoom/Cinema/Full/4:3/Wide).

16 CH ENTER: Enters channels.

17 SLEEP: Sets the sleep timer.

18 DISPLAY: Shows the display.

19 OK: Executes a command.

20 MENU: Displays the on-screen menu.

21 BACK: Returns to the previous menu screen.

22 VOL +/–: Sets the volume.

05-PDP42A3HD-Eng (10-13) 5/17/05, 7:12 PM12

04Part Names

English

13

En

SPLIT SPLIT P IN P SWAP

SPLIT SPLIT

DTV

SIGNAL

MTS LIST

FAVORITE

CH DELETE

INPUT SHIFT

CH+ CH–

MUTING

VOLCH

SPLIT SPLIT P IN P SWAP

SPLIT SPLIT

DTV

SIGNAL

MTS LIST

CH

DELETE

INPUT SHIFT

CH+ CH–

24

25

26

27

23

23 SPLIT Function Buttons

SPLIT: Selects the SPLIT mode (Off, PIP, Twin1

or Twin2).

SPLIT INPUT: Selects an input source for the

sub picture.

P IN P/SHIFT: Selects a position for the sub-

picture.

SWAP: Interchanges the main picture and

sub-picture.

SPLIT CH +, SPLIT CH –: Changes the

channel of the sub-picture.

24 DTV SIGNAL: Displays the signal strength

and quality.

25 MTS: Selects the sound mode.

26 CH DELETE: Deletes a channel in Edit Chan-

nel List.

27 LIST: Displays the channel list. Press the c or

d button to select the required channel.

• When using the remote control unit, point it at the Plasma Display.

Slide

05-PDP42A3HD-Eng (10-13) 5/17/05, 7:12 PM13

05 Preparation

14

En

Installing the Plasma Display

Locating

• Avoid direct sunlight. Maintain adequate ventilation.

• Because the Plasma Display is heavy, be sure to have

someone help you when moving it.

• If you place anything on the top of the Plasma Display it will not

receive enough ventilation and will not operate properly.

• Allow enough space around the upper and back parts when

installing to ensure ventilation around the backside.

Operating Environment

Operating environment temperature and humidity: +0°C to

+40°C (+32°F to +104°F); less than 80% RH (cooling vents not

blocked)

Avoid installing at the following locations:

• Under direct exposure to sunlight

• Under strong artificial light

• In high humidity

•Poorly ventilated

Preventing the Plasma Display from

Falling Over

Be sure to take special care to ensure that the Plasma

Display will not fall over.

Using a wall for stabilization

1

Attach the supplied falling prevention bolts (hooks) to the

Plasma Display.

2

Use storing cords or chains to stabilize the Plasma

Display appropriately and firmly to a wall, pillar, or other

study element.

•Perform this work in the same way for both the left and

right sides.

• Use ropes, chains and fittings that are available on the

market.

•A table or an area of the floor with adequate strength should

always be used to support the Plasma Display. Failure to do

so could result in personal injury and physical damage.

• When installing the Plasma Display, please take the neces-

sary safety measures to prevent it from falling or overturning

in case of emergencies, such as earthquakes, or of acci-

dents.

• If you do not take these precautions, the Plasma Display

could fall down and cause injury.

• The screws, hooks, chains and other fittings that you use to

secure the Plasma Display to prevent it from overturning will

vary according to the composition and thickness of the

surface to which it will be attached.

• Select the appropriate screws, hooks, chains and other

fittings after first inspecting the surface carefully to deter-

mine its thickness and composition and after consulting a

professional installer if necessary.

05 Preparation

Over 10

cm (3

15

/

16

inches)

Over 50 cm (19

11

/16 inches)

1 Hook

2 Cord or chain

3 Fitting

06-PDP42A3HD-Eng (14-17) 5/17/05, 7:29 PM14

05Preparation

English

15

En

Preparing the remote control unit

Inserting batteries

1

Open the battery cover.

2

Insert the supplied two AAA (1.5 V) size batteries.

• The battery polarities must correspond with the (+) and

(–) indicators in the battery compartment.

3

Close the battery cover.

Cautions regarding batteries

• The remote control unit cannot operate the system if the

batteries in the unit are empty. When this happens, replace

the batteries with new ones.

• Do not use manganese batteries. When you replace the

batteries, use alkaline ones.

• Do not mix batteries of different types. Different types of

batteries have different characteristics.

• Do not mix old and new batteries. Mixing old and new

batteries can shorten the life of new batteries or cause

chemical leakage in old batteries.

• Do not leave dead batteries in the remote control unit;

chemical leakage will occur. If you find any chemical leakage,

wipe thoroughly with a cloth.

• The batteries supplied with this product may have a shorter

life expectancy due to storage conditions.

• If you will not use the remote control unit for an extended

period of time, remove the batteries from it.

• WHEN DISPOSING OF USED BATTERIES, BE SURE

TO COMPLY WITH GOVERNMENT REGULATIONS

AND ENVIRONMENTAL PROTECTION GUIDELINES

THAT APPLY IN YOUR COUNTRY OR AREA.

Allowed operation range of the remote control

unit

Operate the remote control unit while pointing it toward the

remote control sensor located at the bottom center of the front

panel of the Plasma Display. The distance from the remote

control sensor must be within 7 m (23 feet) and the angle

relative to the sensor must be within 30 degrees in the right or

left direction.

S

T

A

N

D

B

Y

/O

N

P

O

W

E

R

D

T

V

T

V

C

R

D

V

D

H

D

M

I

S

T

A

N

D

B

Y

30°

Remote control

sensor

7 m (23 feet)

30°

06-PDP42A3HD-Eng (14-17) 5/17/05, 7:29 PM15

05 Preparation

16

En

Cautions regarding the remote control unit

• Do not expose the remote control unit to shock, liquid, or

high humidity.

• Do not place the remote control unit under direct sunlight;

the unit may deform.

• The remote control unit may not work properly if the remote

sensor window of the Plasma Display is under direct sunlight

or strong lighting. In such case, change the angle of the

lighting or Plasma Display, or operate the remote control unit

closer to the remote sensor window.

• When any obstacle exists between the remote control unit

and the remote control sensor, the remote control unit may

not function.

• As the batteries become empty, the remote control unit can

function within a shorter distance from the remote control

sensor. Replace the batteries with new ones if necessary.

• The Plasma Display emits very weak infrared rays from its

screen. If you place such equipment operated through

infrared remote control as a VCR nearby, that equipment may

not receive commands from its remote control unit properly

or entirely. If this is the case, place that equipment at a

location far enough from the Plasma Display.

• Depending on the installation environment, infrared rays

from the Plasma Display may not allow this system to

properly receive commands from the remote control unit or

may shorten allowable distances between the remote control

unit and the remote control sensor. The strength of infrared

rays emitted from the screen differs, depending on images

displayed on the screen.

Cable connections for watching digital

and/or conventional TV channels

This system is equipped with two terminals for inputting TV

broadcasting signals: ANTENNA/CABLE IN and DTV-ANTENNA

IN. The ANTENNA/CABLE IN terminal accepts conventional TV

broadcasting signals. The DTV-ANTENNA IN terminal accepts

digital TV broadcasting signals. When using a cable TV to

watch conventional TV channels, connect to the ANTENNA/

CABLE IN terminal as shown.

Connecting to an Aerial

To view TV channels correctly, the Plasma Display must receive

a signal.

Connecting the aerial of digital TV

When you connect the aerial of digital TV, connect the outdoor

aerial.

DTV-

ANTENNA IN

Connecting the aerial of analog TV

There are three ways to connect the aerial or network input

cable for analog TV.

It is recommended to connect the outdoor aerial for the best

outcome of the images.

Cable

Converter

ANTENNA

/ CABLE IN

Cable TV

06-PDP42A3HD-Eng (14-17) 5/17/05, 7:29 PM16

05Preparation

English

17

En

Power cord

Connecting the power cord

Connect the power cord after all component connections are completed.

Plasma Display (rear view)

DTV-

ANTENNA IN

ANTENNA

/ CABLE IN

MONITOR OUT

VIDEO

VIDEO 1

L-AUDIO-R S-VIDEO 1

AUDI O

DIGITAL OUT

OPTICAL

R

L

HDMI

INPUT

SERVICE ONLY AC IN

AUDI OHDMI

R

L

VIDEO 2 L-AUDIO-R

L-AUDIO-R Y

C

B

/P

B

C

B

/P

B

C

R

/P

R

C

R

/P

R

COMPONENT 2

COMPONENT 1

S-VIDEO 2

• Use only the supplied power cord.

• Be sure to use the specified power supply voltage;

neglecting this can result in fire or electric shock.

•For the Plasma Display, a three-core power cord with a

ground terminal is used for efficiency protection.

Always connect the power cord to a three-pronged

outlet and make sure that the cord is properly grounded.

• Always turn off the power of the Plasma Display when connecting

the power cord.

• Disconnect the power cord from the power outlet when the Plasma

Display is not going to be used for a long period of time.

06-PDP42A3HD-Eng (14-17) 5/17/05, 7:29 PM17

06 Basic Operations

18

En

Turning the power on and off (Standby)

1

Press the POWER button on the bottom of the Plasma

Display to enter the standby mode.

• The STANDBY indicator lights up.

2

Press the TV button on the remote control or the

STANDBY/ ON button on the bottom of the Plasma

Display.

• The Plasma Display switches to on. The STANDBY

indicator lights off and the current input source

indicator lights up.

3

To switch the Plasma Display off, press the TV button

on the remote control or the STANDBY/ ON button on

the bottom of the Plasma Display for 1 second.

• The Plasma Display enters to standby mode and the

STANDBY indicator lights up instead of the current

input source indicator.

4

To switch the Plasma Display off completely, press the

POWER button on the bottom of the Plasma Display.

• The STANDBY indicator lights off.

• If you are not going you use the Plasma Display for a long period of

time, press POWER button on the bottom of the Plasma Display

to switch the Plasma Display off completely and disconnect the

power cord of the Plasma Display from a wall outlet.

• If the Plasma Display is switched off completely, you cannot turn the

Plasma Display on by pressing the TV button on the remote

control.

• If the Plasma Display is switched off completely, it cannot switch the

Plasma Display on automatically by the “On Timer“ setting.

06 Basic Operations

PO

W

ER

DTV TV VCR DVD HDMI

STANDBY

/ON

DTV TV VCR DVD HDMI

STANDBY

POWER

button

STANDBY indicator

STANDBY/ON button

Current input source indicator

07-PDP42A3HD-Eng (18-22) 5/17/05, 7:28 PM18

06Basic Operations

English

19

En

Watching TV channels

Unless you set up TV channels that you can watch under the

current conditions, you cannot tune in those channels. For the

procedure, see “Setting up TV channels” on page 24.

• When watching a digital TV program, you may see emergency alert

messages scrolling at the top of the screen. Those messages are

broadcast by TV stations as necessary when in emergency situations.

Selecting the analog and digital channels

You can select the input mode between analog and digital

channels by pressing the INPUT button.

• When you switch the input mode, the last channel you previously

selected will be received.

Changing channels

To increase the channel number, press the CH + button on the

remote control unit. To decrease the channel number, press the

CH – button .

• CHANNEL +/– on the Plasma Display has the same

function as CH +/– on the remote control unit.

Using 0 – 9 on the remote control unit

Select channels directly by pressing buttons 0 to 9.

EXAMPLE

•To select channel 5 (1-digit channel), press 5.

•To select channel 25 (2-digit channel), press 2 then 5.

•To select channel 125 (3-digit channel), press 1, 2, then 5.

•To select subchannel 10-1, press 1, 0, •(dot), then 1.

•Pressing the CH ENTER button after entering the channel number,

enables you select channels quickly.

•To return to the previous channel, press the CH RETURN button.

MUTING

VOLCH

C.C.

FAVORITE

CH

RETURN

EXIT BACK

MENU

SLEEP

DISPLAY

SCREEN SIZESOUND EFFECT

HD WIDEINPUT

TV

AV SELECTION

11 3322

44 6655

77 9988

CH

ENTER

00

OK

07-PDP42A3HD-Eng (18-22) 5/17/05, 7:28 PM19

06 Basic Operations

20

En

Changing the volume and sound

To increase the volume, press the VOL + button on the remote

control unit. To decrease the volume, press the VOL – button.

• The VOLUME +/– buttons on the Plasma Display operates

the same as the VOL +/– buttons on the remote control unit.

•To mute the sound output, press the MUTING button. “

”

appears on the screen. To quit muting, press the MUTING

button again. Pressing the VOL + button also quits muting.

Plasma Display

(bottom view)

STANDBY

/ON

MUTING

VOLCH

Volume adjustment

Volume 4

Muting

VOLUME –/+ buttons

Displaying Information

You can display the channel information and setting status you

selected.

Press the DISPLAY button.

For analog

TV 3

C9

Mono

8:30am

For SPLIT

Mono

TV 3

C9

DTV 112

8:30am

For external input

VIDEO1

8:30am

Press the DISPLAY button.

For digital

If you press the DISPLAY button again, program

description is displayed.(This may be unavailable for

some programs.)

NBC Sports

8 : 30 a m

DTV 11-2DTV 11-2

For SPLIT (digital reception)

NBC Sports

VIDEO 1

8:30am

DTV 11-2DTV 11-2

07-PDP42A3HD-Eng (18-22) 5/17/05, 7:28 PM20

Page is loading ...

Pioneer PDP-4214HD User manual

This manual is also suitable for

Pioneer PDP-4214HD User manual

in other languages

Related papers

Other documents