Jacobsen E-Walk Owner's manual

Brand
Jacobsen
Model
E-Walk
Category
Lawnmowers
Type
Owner's manual

This manual is also suitable for

Instruction
Sheet
When Performance Matters.
™
WARNING
If incorrectly used, this machine can cause severe injury. Those who use
and maintain this machine should be trained in its proper use, warned of its
dangers and should read the entire manual before attempting to set up,
operate, adjust or service the machine
19
17
18
13
6
5
9
15
16
7
8
10
4
3
11
1 - INCLUDES ITEMS 3 - 16
GB
Mower Caddy Mounting Kits
63310 - Eclipse 122F
68649 - Jacobsen 418, 518 and Eclipse 118
68650 - Jacobsen 422, 522, 522T and Eclipse 122
68651 - Jacobsen 426, 526 and Eclipse 126
68652 - Jacobsen PGM and Ransomes 22
68653 - Toro Greenmaster 1000
68654 - John Deere 220A
68672 - Jacobsen Tournament Cut 22
2701021-Rev B
2
This kit is intended for use with Mower Caddy and specific
walk behind units.
1. Park the tractor on a flat and level surface, fully lower
the cutting units to the ground, engage the parking
brake, turn the ignition switch to the off position, and
remove the key.
a. Wait for all movement to stop before making any
adjustments or modifications.
b. Allow sufficient time for the unit to cool down.
c. Take this opportunity to thoroughly inspect the
equipment and perform other required maintenance.
Mower Latch __________________________________________________________
1. (Units 68649~68654 and 63310) Loosely assemble
left and right mower latch brackets (A and B) to mower
bed, using four 3/8-16 x 1-1/4” carriage bolts, flat
washers, lockwashers and nuts (C). Do not tighten
hardware.
(Unit 68672) Loosely assemble left and right mower
latch brackets (A and B) to mower bed, using spacers
(Z) four 3/8-16 x 3” carriage bolts, flat washers, lock-
washers and nuts (C). Do not tighten hardware.
2. Assemble two springs (D) to brackets (A and B), using
5/16-18 x 1-1/2” screws (E), 5/16-18 hex nuts (F) and
5/16-18 center lock nuts (G).
3. Assemble mower latch bar (H) to brackets (A and B)
using two shoulder bolts (K), 1/2” flat washers and
center lock nuts (J).
4. Attach springs (D) to mower latch bar (H).
Figure 1
Extension Brackets (Jacobsen 426 and 526 and John Deere 220A Mowers Only) _
1. If your Jacobsen 426 or 526 mower has a Turf
Groomer attached, or if you have a John Deere 220A
mower, use only one extension bracket (L) installed on
the right side of the trailer bed in Position 1.
If your Jacobsen 426 or 526 mower does not have a
Turf Groomer attached, use both extension brackets
(L), one installed on left and right side of trailer bed in
Position 2.
2. Assemble bracket(s) (L) to side of trailer bed using 3/8-
16 x 1-1/4” hex head screws, flat washers, lockwashers
and nuts (M).
NOTE: When placing mower on trailer, Jacobsen 426 and 526
units with a Turf Groomer installed and John Deere 220A
mowers will not sit centered on the trailer bed. The mower will
be offset from center, away from the lift / lower handle.
Figure 2
CAUTION
Before you install this kit, read the tractor’s manual to
become familiar with the tractor, the controls and
proper use of the equipment.
Stay alert for potential hazards and follow all safety
precautions. Read all instructions completely and
make sure you understand them before proceeding
with the assembly.
!
WARNING
Before you attempt to clean, adjust, or repair any of
this equipment, disengage all drives, shut down the
engine and allow the unit to cool. Remove the key
from the ignition switch and disconnect the negative
battery terminal to prevent accidental discharge and
potential bodily injuries.
!
A
B
C
D
E
F
G
H
K
C
J
J
Z
(68672 ONLY)
Z
(68672 ONLY)
L (Position 1)
L (Position 2)
M
M
M
L
(Units without Groomer Only)
Litho in U.S.A. 9-2007
3
Mower Rest Hooks (Units 68649~68654 and 63310 Only) _____________________
1. Refer to Figure 4 to determine which set of mounting
holes are used for your mower.
2. Assemble Mower rest hooks (N) to corresponding
holes in trailer bed using eight 3/8-16 x 1-1/4” screws,
flat washers, lockwashers and nuts (P). Do not tighten
hardware.
Figure 3
Figure 4
N
N
P
P
Jacobsen 418
Jacobsen 518
Eclipse 118
Eclipse 118F
Jacobsen 422
Jacobsen 522
Jacobsen 522T
Jacobsen PGM
Ransomes 22
Toro 1000
Eclipse 122
Eclipse 122F
Jacobsen 426
Jacobsen 526
Eclipse 126
(Without Turf Groomer)
Jacobsen 426
Jacobsen 526
Eclipse 126
(With Turf Groomer)
John Deere 220A
4
Mower Catch Rod______________________________________________________
1. Place mower on kickstand, and remove transport tires.
Remove mower from kickstand.
2. Remove hardware (Q) securing handle adjustment
brackets (R) to mower frame.
NOTE: All mowers use a different style handle adjustment
bracket and catch rod. The Jacobsen Greens King 518 mower
is shown as reference. Installation is similar for all other
mowers.
3. Secure catch rod (S) to mower using hardware (Q).
Figure 5
Rubber Strip (68672 Units Only) __________________________________________
1. Cut rubber strip into three 12 inch (305 mm) pieces.
2. Center first rubber stip (X) on trailer bed. Place
remaining two strips (Y) leaving a 1.0 inch ( 25 mm)
gap between strips.
Figure 6
Q
R
S
68649~68652 & 63310 Style
68653~68654 Style
68672 Style
X
Y
Y
5
Final Adjustments _____________________________________________________
1. Lower trailer to ground, and place mower onto trailer
bed.
NOTE: Note the rear of the mower should face the front of
trailer.
2. Raise Trailer for access to bracket mounting hardware.
3. (Units 68649~68654 and 63310) Adjust mower until it
is centered on the trailer bed, the catch bar is engaged
in mower latch (H) and resting on mower rest hooks
(N). Adjust rest hooks (N) and latch brackets (A and B)
to mower and securely tighten all hardware.
NOTE: When placing mower on trailer, Jacobsen Greens King
426, 526 and Eclipse 126 units with a Turf Groomer installed
and John Deere 220A Mower will not sit centered on the trailer
bed. The mower will be offset from center, away from the lift /
lower handle.
4. (Units 68672 Only) Adjust mower until it is centered on
the trailer bed, the catch bar is engaged in mower latch
(H). Adjust latch brackets (A and B) to mower and
securely tighten all hardware.
5. (Units 68672 Only) Route tie strap over reel frame and
under catcher frame. Secue by hooking ends under
enge of trailer bed.
6. (Units 63310 Only) Secure both ends of floating reel
frame to trailer bed using rubber tie downs (Z). Hook
one end of tie down to bedknife adjuster blocks and
other end to cutout in trailer bed.
Figure 7
Figure 8
H
N
A
B
Z
6
2
3
3
3
5
6
6
6
7
8
9
10
12
12
12
11
13
14
16
18
19
20
20
21
22
4
4
4
17
15
1
1
1
23
MOWER CADDY
Mower Mounting Kits
Walk Behind Reel Type Mower Kit No.
Jacobsen Greens King 418 and 518, Eclipse 118 68649
Jacobsen Greens King 422, 522 and 522T, Eclipse 122 68650
Jacobsen Greens King 426, 526, Eclipse 126 68651
Jacobsen PGM and Ransomes 22 68652
Toro 1000 68653
John Deere 220A 68654
Jacobsen Tournament Cut 22 67672
Jacobsen Eclipse 122F 63310
7
> Change from previous revision
Item Part No. Description
6
8
6
4
9
6
8
6
5
0
6
8
6
5
1
6
8
6
5
2
6
8
6
5
3
6
8
6
5
4
6
8
6
7
2
6
3
3
1
0
1
446142 Lockwasher, 3/8 Heavy 12 12 16 12 12 16 4 12
2 400192 Screw, 5/16-18 x -1/12” Hex Head 2 2 2 2 2 2 2 2
3 443110 Nut, 3/8-16 Hex 12 12 16 12 12 16 4 12
4 400264 Screw, 3/8-16 x 1-1/4” Hex Head 8 8 12 8 8 12 0 8
5 443106 Nut, 5/16-18 Hex 2 2 2 2 2 2 2 2
6 453009 Flat Washer 12 12 16 12 12 16 4 12
7 453017Flat Washer, 1/2 22222222
8 365033 Shoulder Bolt, 3/8-16 2 2 2 2 2 2 2 2
9 440120 Carriage Bolt, 3/8-16 x 1-1/4” 4 4 4 4 4 4 0 4
9 440134 Carriage Bolt, 3/8-16 x 3” 0 0 0 0 0 0 4 0
10 444718 Locknut, 5/16-18 Center 2 2 2 2 2 2 2 2
11 444762 Locknut, 3/8-16 Center 2 2 2 2 2 2 2 2
12 2809705 Bracket, Extension 0 0 2 0 0 4 0 0
13 2809736.7 Hook, Left Rest 1 1 1 1 0 0 0 1
13 2809912.7 Hook, Left Rest 0 0 0 0 1 1 0 0
14 2809737.7 Hook, Right Rest 1 1 1 1 0 0 0 1
14 2809913.7 Hook, Right Rest 0 0 0 0 1 1 0 0
15 4138344Rod, Catch 10000000
15 4138345Rod, Catch 01000001
15 4138346Rod, Catch 00100000
15 4138347Rod, Catch 00010000
15 4138349Rod, Catch 00001000
15 4138350Rod, Catch 00000100
15 4129476Rod, Catch 00000010
16 2809765.7 Mower Latch 1 1 1 1 1 1 1 1
17 2809837 Spring, Extension 2 2 2 2 2 2 2 2
18 2809841.7 Bracket, Right Mower Latch 1 1 1 1 1 1 1 1
19 2809842.7 Bracket, Left Mower Latch 1 1 1 1 1 1 1 1
20 4129477 Spacer, TC 22 0 0 0 0 0 0 1 0
21 4129478 Tie Down 0 0 0 0 0 0 1 0
22 4129479 Strip, 36” Adhesive Rubber 0 0 0 0 0 0 1 0
23 4170602 Rubber Tie Down 0 0 0 0 0 0 0 2
Jacobsen, A Textron Company
11108 Quality Drive, Charlotte, NC 28273
www.Jacobsen.com
800-848-1636
Equipment from Jacobsen is built to exacting
standards ensured by ISO 9001 and ISO 14001
registration at all of our manufacturing locations.
A worldwide dealer network and factory trained
technicians backed by Jacobsen Parts Xpress
provide reliable, high-quality product support.
When Performance Matters.
™
  • Page 1 1
  • Page 2 2
  • Page 3 3
  • Page 4 4
  • Page 5 5
  • Page 6 6
  • Page 7 7
  • Page 8 8

Jacobsen E-Walk Owner's manual

Brand
Jacobsen
Model
E-Walk
Category
Lawnmowers
Type
Owner's manual
This manual is also suitable for
Download PDF
report

Ask a question and I''ll find the answer in the document

Finding information in a document is now easier with AI

Related papers

Other documents