2. National
  3. Epicenter Single End Panel

National Epicenter Single End Panel Assembly Instruction

  • Hello! I am an AI chatbot trained to assist you with the National Epicenter Single End Panel Assembly Instruction. I’ve already reviewed the document and can help you find the information you need or explain it in simple terms. Just ask your questions, and providing more details will help me assist you more effectively!
Epicenter Single
End Panel
Proper product installation, in accordance with these instructions, is the responsibility of the installing agent. If you have any
questions concerning these instructions, please call National Customer Service 800.482.1717.
Assembly Instruction
1
Telephone 800.482.1717
Fax 812.482.8800
www.NationalOfficeFurniture.com
Part #2439929
Rev,B
Printed in U.S.A
© 2014 Kimball International, Inc.
Recommended Tools
• Drill with 5/16" bit
• Phillips head screwdriver
• Tape Measure
• 3" wide masking tape
• Pencil
Package Contents Qty.
• End Panel 1
• #8 x 5/8" Pan Head
Screws 4
• 1/4-20 x 2 1/2" Flat Head
Machine Screws 2
• L Bracket 1
2nd Package Contents Qty.
• Epicenter Bracket 1
• #10 x 1" Pan Head
Screw 7
• #10-32 x 3/4" Screws 2
• #10-32 Wellnut 2
Figure A
2
In the desired location, place 3" wide
masking tape where the end panel and
epicenter intersects with the lower
unit. Using a pencil mark the location
of the ends and sides of the end panel
(Figure C). NOTE: If two end panels are
used, mark each one.
Figure C
3
Using a tape measure and pencil, mark the
locations shown in (Figure D) measuring
from the corners marked in step #3 for
boring holes for two (2) 1/4-20 x 2 1/2"
Flat Head Machine Screws per end panel.
Drill two (2) 5/16" holes through the
lower worksurface per end panel. If (2)
end panels are used mark and bore 4
holes.
4
Drill
Figure D
Note: For better clarity, this Instruction does not always show the undersurface
pedestal or other undersurface components.
On a smooth clean dry surface place the
end panel. Attach the Epicenter bracket
ush to the top of the end panel, with
three (3) #10 x 1" pan head screws. Place
the L-bracket on the end panel, attach
with two (2) #8 x 5/8" pan head screws
(Figure A).
NOTE: Epicenter bracket comes in sepa-
rate package from the end panel. If two
end panels are used, attach epicenter
brackets to the epicenter rst, then
center and attach each end panel.
#10 x 1" Pan Head Screws
#8 x 5/8"
Pan Head
Screws
Epicenter
Bracket
Determine the proper end and placement of the epicenter bracket per your conguration
to attach the end panel to the epicenter. Attach with (2) #10-32 x 3/4" screws and (2)
#10-32 wellnuts. (See Figures A and B). Note: Hand start before fully fastening.
Use 10-32 screws
through C channel
Figure B
37/64"
1 31/64"
Drill 5/16"
holes.
Insert Wellnut
Into Bracket
Figure A
If wellnut doesn’t fit
into bracket, use
wellnut as a nut
underneath bracket.
Epicenter Single
End Panel
Assembly Instruction
Proper product installation, in accordance with these instructions, is the responsibility of the installing agent. If you have any
questions concerning these instructions, please call National Customer Service 800.482.1717.
Attach the worksurface to the epicenter
bracket with four (4) #10 x 1" pan head
screws. Attach the L brackets with two
(2) #8 x 5/8" pan head screws (Figure
E).
NOTE: If two end panels are used repeat
process for the other end panel.
NOTE: Repeat
process if two end
panels are used.
Figure E
5
6
With the upper and lower units
positioned in the desired locations,
install two (2) 1/4-20 x 2 1/2" Flat
Head Machine screws through the
lower worksurface into the end
panel (Figure F).
NOTE: If two end panels are used
repeat process for the other end
panel.
Figure F
Two (2) 1/4-20 x 2 1/2" FH
Machine Screws
#10 x 1" Pan
Head Screws
#8 x 5/8"
Pan Head
Screws
NOTE: Repeat
process if two end
panels are used.
/