Replas Kimberley Kingfisher Assembly Instructions

Brand: Replas

Model: Kimberley Kingfisher

Type: Assembly Instructions

KIMBERLEYKINGFISHER

1.Usinga5mmhexagonaldrive,partscrew(acoupleofturnsonly)eachslatontotheirrespectiveseatsupports

startingfrombackoftheseattothefront,thenfromthebottomofthebacksupporttothetop.



2.Ensurethattheseatslatsareatrightanglestothesupportsandthatthesupportsarevertical.



3.Finallytightenallscrewstakingcarenottoovertightenasthiscouldstripthethreadintheseatsupport.

COMPONENTSLIST

ASSEMBLYINSTRUCTIONS

IMPORTANT:Pleasereadcarefullybeforeassembling.

13xSeatSlat—40mmx40mm

3xSeatSupports

39xBugleScrew—14gx75mm

Ifyourequirefurtherinstallation

assistance,pleasecontactyoursupplier.

DAINTREEKINGFISHER

KINGFISHER 1.8m Seat

450mm

790mm

460mm

790mm

525mm 570mm

ASSEMBLYINSTRUCTIONS

IMPORTANT:Pleasereadcarefullybeforeassembling.

PLEASENOTE:

Topbackandbottomfrontslatshavebothoutsideedgesrounded



1.Usinga5mmhexagonaldrive,partscrew(acoupleofturnsonly)eachslat

ontotheirrespectiveseatsupports



2.Ensurethattheseatslatendsarealignedandatrightanglestothesupports

thentightenallscrews,takingcarenottoovertighten,asthiscouldstripthe

threadintheseatsupport.



3.Drillordigholesapproximately500mmdeep(dependingontheheightyou

wanttheseatabovetheground)at705mmcentres.



4.Placethesupportsoftheassembledseatintotheholes.Positiontheseatand

ensurethattheseatiswellbracedtopreventmovementandsagging.Atthis

stageitisimportanttouseaspiritleveltocheckthattheseatishorizontal

andthesupportsarevertical.



5.Oncesatisfiedthattheseatispositionedcorrectly,filltheholeswith

concrete,makingsureitispackedfirmlyaroundthesupports.Oncethe

concretehasset,removethebracing.



SUGGESTION:

WheninstallingInͲGroundfurnitureitisagoodideatonailsometimberbracing

acrossthebackofallsupports.Thiswillensureallsupportsarekeptparallelandin

alignment,aswellaspreventinganysaggingoftheseatduringinstallation.Donot

removebracinguntilafterconcretehasset.

COMPONENTSLIST

KimberleyKingfisher

Seat

InGround

1.8m

Ifyourequirefurtherinstallation

assistance,pleasecontactyoursupplier.

KIMBERLEYKINGFISHER1.8m

13xSeatSlat—40mmx40mm

3xInGroundSeatSupports

39xBugleScrew—14gx75mm

KIMBERLEYKINGFISHER1.1m

13xSeatSlat—40mmx40mm

2xInGroundSeatSupports

26xBugleScrew—14gx75mm

800mm

450mm

500mm

Bracing

Replas Kimberley Kingfisher Assembly Instructions

Brand: Replas

Model: Kimberley Kingfisher

Type: Assembly Instructions

Download PDF

report

Replas Kimberley Kingfisher Assembly Instructions

Replas Kimberley Kingfisher Assembly Instructions

Other documents