CyClone SC502 Installation And Operation Instructions Manual

Brand: CyClone

Model: SC502

Category: Cooker hoods

Type: Installation And Operation Instructions Manual

This manual is also suitable for

Self-Cleaning Range Hoods

Models:

Installation and Operation Instructions

Please read all instructions before installing and operating.

All wiring and installation must be in accordance with CEC, NEC and local electrical codes.

READ AND SAVE THESE INSTRUCTIONS

Wall Mount and Island Range Hoods

SC(B)500, SC(B)501, SC(B)502, SC(B)503, SC510,

SC(B)513, SC(B)514, SI(B)323, SI(B)520, SI(B)521,

SI(B)522, SI(B)523, SI530, SI531

SC322, SCB722, SC712, SC(B)715, SCB717,

SCB718, SC720, SC(B)722

2Cyclone Canopy Installation - English

3Cyclone Canopy Installation - English

Important Safety InStructIonS

• isappliancemustbeinstalledbyaqualiedtechnician.

• emanufacturerdeclinesallresponsibilitiesintheeventof

failuretoobservetheinstructionsgivenhereforinstallation,

maintenanceandsuitableuseoftheproduct.

• emanufacturerfurtherdeclinesallresponsibilityforinjury

duetonegligence,andthewarrantyoftheunitautomatically

expiresduetoimproperinstallationandmaintenance.

WARNING

• Forindooruseonly.

• Forgeneralventilationuseonly.Donotusetoexhausthazardous

orexplosivematerialsorvapors.

• Twoinstallersarerecommendedbecauseofthesizeand

weightofthishood.

CAUTION

TO REDUCE THE RISK OF FIRE, ELECTRIC SHOCK, OR

INJURY TO PERSONS, OBSERVE THE FOLLOWING:

1. Usethisunitonlyinthemannerintendedbythemanufacturer.

2. Before servicing or cleaning the unit, switch power o

atservicepanelandlockservicepaneltopreventpower

from being switched on accidentally. When the service

disconnectingmeanscannotbelocked,securelyfastena

prominentwarningdevicetotheservicepanel.

3. Installationworkandelectrical wiringmustbedoneby

qualiedpersonsinaccordancewithallapplicablecodes

andstandards,includingre-ratedconstruction.

4. Sucientairisneededforpropercombustionandexhausting

of gases through the ue of fuel burning equipment to

prevent back draing. Follow the heating equipment

manufacturer’sguidelineandsafetystandardsaspublished

bythelocalcodeauthorities.

5. Whencuttingordrillingintowallsorceilings,becareful

nottodamageexistingelectricalwiringandotherhidden

utilities.

6. Toreducetheriskofre,electricshockandtoproperly

exhaustair,ductedfansmustalwaysbeventedoutdoors.

Donotventexhaustairintospaceswithinwalls,ceilings,

attics,crawlspaces,orgarages.Donotconnectthisfan

withanysolid-statespeedcontroldevice.

7. Alwayskeeptheductcleartomaintainproperairowfor

venting.

8. ebottomofthehoodMUSTNOTBELESSthan28”

and at a suggested maximum of 36” above cooktop for

bestcapture ofcookingimpurities.Foragas range,the

bottomofthehoodMUSTNOTBELESSthan30”above

cooktop.

WARNING

TO REDUCE THE RISK OF RANGE TOP GREASE FIRE:

1. Neverleavetherangeunattendedathighsettings.

2. AlwaysturnhoodONwhencookingathighheatorwhen

amingfood.

3. Useproperpansize.Alwaysusecookwareappropriatefor

thesizeofthesurfaceelement.

4. Keep fan, lters and grease laden surfaces clean. Clean

ventilatingfansfrequently.Donotallowgreasetoaccumulate

onfanorlter.

5. UseHIGHsettingonhoodonlywhennecessary.

6. Don’tleavehoodunattendedwhencooking.

7. Toreducetheriskofre,useonlymetalductwork.

8. isunitmustbegrounded.

9. Notforoutdooruse.

WARNING

• Donotrepairorreplaceanypartofthisapplianceunless

specicallyrecommendedinthisbook.Allotherservice

shouldbeperformedbyaqualiedtechnician.

• e hood motor has a thermal overload that will

automaticallyshutothemotorifitbecomesoverheated.

emotorwillrestart.Ifthemotorcontinuallyshutso

and restarts, contact the Cyclone service department.

Ensure that the hood is mounted at the recommended

mountingheight.

• isproductmayhavesharpedges.Becarefultoavoid

cutsandabrasionsduringinstallationandcleaning.

WARNING

4Cyclone Canopy Installation - English

contentS

Important Safety Instructions 3

Damage Inspection 4

Ducting 4

Mounting Heights and Clearance 5

Wiring Installation 5

Wall Mount Installation - Tools and Materials Required 6

Wall Mount Installation - Parts Supplied 6

Wall Mount Hood Installation 7

Island Installation - Tools and Materials Required 8

Island Installation - Parts Supplied 8

Island Hood Installation 9

Canopy Hoods Specications 11

Troubleshooting 37

Control Panel 38

Maintenance 38

Cyclone Range Hoods Limited Warranty 39

5Cyclone Canopy Installation - English

Damage InSpectIon

• Pleasefullyinspectunitfordamagebeforeinstallation.

• Iftheunitisdamagedinshipment,returntheunittothestoreinwhichitwasboughtforrepairorreplacement.

• Iftheunitisdamagedbythecustomer,repairorreplacementistheresponsibilityofthecustomer.

• Iftheunitisdamagedbytheinstaller(ifotherthanthecustomer),repairofreplacementmustbemadebyarrangementbetween

customerandinstaller.

• Onceinstalled,alldamageswillbeassumedtheresponsibilityoftheinstaller.

DuctIng

• Toreducetheriskofre,useonlymetalductwork.

• Toreduceriskofreandtoproperlyexhaustair,besure

toductairoutside–donotventexhaustairintospaces

withinwalls,ceilings,attics,crawlspaces,orgarages.

WARNING

• Best to use rigid type metal ducts. Flexible ducts can

restrictairowbymorethan50%.

• Reducethenumberoftransitionsandturnsasmuchas

possible.Ifareducerisused,installalongreducerinstead

ofapancakereducer.Ifturnsandtransitionsarerequired,

installthemasfarawayfromtheopeningaspossibleand

asfarapartbetweentwoaspossible.

CAUTION

• 6”roundductworkmustbeusedtomaintainmaximum

airoweciencywithmotorsof300CFMorgreater.If

theuseofanysizeductingislessthan6”,thewarrantyis

automaticallyvoided.

• eventingductmustgohorizontallyorverticallyuptothe

outsidewallortheroof.Ifitisturneddownwardanywhere

intheventingsystem,thewarrantyisautomaticallyvoided.

WARNING

Fastenallconnectionswithsheetmetalscrewsandtapealljoints

withcertiedsilvertapeorduct.

Donotcutajoistorstudunlessabsolutelynecessary.Ifajoistor

studmustbecutthenasupportingframemustbeconstructed.

Beforemakingcutoutsmakesurethereisproperclearancewithin

theceilingorwallfortheexhaustvent.

Examples of dierent types of ventilation for island

and wall mounted canopies:

Additional parts not provided.

Roof Pitch with Cap

and Flashing

Side wall cap with

gravity damper

Soffit or crawl space

Side wall cap with

gravity damper

6Cyclone Canopy Installation - English

mountIng HeIgHtS anD clearance

• ehoodshouldbeinstalledat28”minimumabovethe

cookingsurface.Ifpairingyourrangehoodwithagas

stoveminimummountingheightmustbe30”abovethe

cookingsurface.

WARNING

Minimum mount height between range top to hood bottom should

benolessthan28”forelectricorceramicstoves,andnolessthan30”

forgasstoves.emaximummountheightshouldbenomorethan

36”.ehoodmustbeinstalledatthecorrectmountingheight.Hoods

mounted too lowcouldresultinheatdamage.Hoodsmountedtoo

high, on the other hand, will be less eective and performance may

suer.

Checkyourceilingheightandthehoodheightmaximumbefore

youselectyourhood.

Hoodinstallationheightabovecooktopistheuser’spreference.

elowerthehoodisabovethecooktopthemoreecientitwill

beindrawingoutcookingodors,greaseandsmoke.

WIrIng InStallatIon

Grounding Instructions

isappliancemustbegrounded.

isapplianceisequippedwithacordhavingagroundingwireor

withaplughavinggroundingwire.egroundingwiremustbe

groundedproperlyinthejunctionboxortheplugmustbeplugged

intoanoutletthatisproperlyinstalledandgrounded.

1. Connectthepowerlinegroundwiretothegreengroundwire

suppliedwiththehood.

2. Connecttheblackpowerwiretotheblackwiresuppliedwith

thehood.

3. Connectthewhiteneutralwiretothewhitewiresuppliedwith

thehood.

Min: 3”

Max. 2 ¾”

Install the Electrical Power Supply

Positiontheoutletorjunctionboxwithinthespacecoveredbythe

ductcover.Placetheoutletorjunctionboxatamaximumdistance

of24”fromwherethecordexitsfromthehood.ecenterofthe

outletorjunctionboxshouldbepositionedat2¾”awayfromthe

centerofthefuturehoodlocation.Makesurethisdoesnotinterfere

withthemountingareaorwiththeductcover.

Min:

Ceramic/Electric

28”

Gas 30”

Max: 36”

36”

Green: Ground

White: Neutral

Black: Power

is appliance requires 120V 60Hz electrical supply and connection to an individual properly grounded branch circuit protected

by a circuit breaker or time delay fuse.

7Cyclone Canopy Installation - English

WALL MOUNT INSTALLATION - PARTS SUPPLIED

1 × Hood 1 × Chimney Flues

(Top and Bottom)

1 × Round Adapter

(May be Pre-Installed)

1 × Upper Mounting Bracket

HARDWARE PACKAGE

4 × Mounting Screws

(Long and Medium, 2 each)

4 × Drywall Anchors

(Large and Small, 2 each)

2 × Washers

1 × Oil Cup

6 × Damper Screws

2 × Top Chimney Screws SC500, SC711, SC715 ONLY:

2 × Bottom Chimney Screws

WALL MOUNT INSTALLATION - TOOLS AND MATERIALS REQUIRED

• Electrical drill or ratchet driver

• ½” drill bit for drilling pilot holes

• 1 ¼” drill bit for drilling electrical wiring acess

hole (if applicable)

• Phillips screwdriver #2 or driver bit

• Wire stripper or cutter

• Tape measure

• Aluminum foil tape and/or duct tape

• Electrical supplies for wiring (i.e. marrets,

electrical tape)

• Hammer

• Jigsaw or saber saw

• Drywall stud (if applicable)

• Step latter

• Stud

• Level

1 × Plastic Damper Cover

PRE-INSTALLED

2 or 4 × G4 Type Lights

(12V, 20W)

PLEASE REFER TO PAGES 11-37 FOR YOUR MODEL’S SPECIFICATIONS

8Cyclone Canopy Installation - English

Install the Wall Mount Hood

1. Measure from range top to hood bottom and use a leveler

to mark line A (28” minimum from range top for electric/

ceramicstoves,30”minimumfromrangetopforgasstoves).

2. PlaceandmarkcenterlineC/L.

3. Use the hood fan as template to nd the mounting screws

position. Keep the hood bottom centered and level on line

A.Markthepositionofthetwomountingscrews(Figure1).

Important: e minimum allowable distance from the top of the

damper on range hood to the bottom of the ductwork protruding

from wall is 3”.

4. Fastentwomountingscrewsintostudswherepossibleatthe

positionsmarkedwithanX.Donotfastenscrewsalltheway.

5. Wherestudsarenotavailable,youmustconstructwoodwall

framing that is ush with surface of wall studs. Wood wall

framingshouldbeatleast1/2”thickand3”high.Assemble

wood wall framing to wall studs for a secure installation.

Makesuretheheightoftheframingallowsthehoodfantobe

securedtothewoodblock(Figure2).

6. Centertheuppercovermountingbracketwiththecenterline

andmountitushwiththeceilingbydrillingpilotholesand

usingsmallanchorsprovided(Figure3).

7. Install6”roundadapterifnotpreinstalled.

8. Removetheltersfromthehood.

9. Hang hood onto screws and hand tighten. If possible, use

extrascrewstofurthersecurethehoodtothewallfrominside

thehood.

10. Install 6” round duct over the adapter, connect it with the

ventingductcomingfromthewallorceiling.Usemetalfoil

ducttapetosealthejoint.

11. Installelectricalconnection.Turnonthehoodandcheckfor

leaksaroundducttape.

12. Placetelescopicductcoversontohoodandextendinnertop

ductcoverupwardsandsecuretoductcoverbracket.

13. Reinstall lters to the hood. Remove protective plastic lm

coveringtheductcoversandhood.

• Woodblockingmayneedtobeaddedbehindthedrywall

ifno studsarepresent.Wallanchorsmay also be used,

checklocalcodesbeforeusingwallanchors.

CAUTION

• Whencuttingordrillingintowall,donotdamageelectrical

wiringandotherhiddenutilities.

WARNING

Min. 3”

Min. 1 ½” Framing Behind

Drywall

Wall Studs

C/L

Min. 28-30”

Min. 3”

Ceiling

Screw Locations

Mounting Bracket

Flush with Ceiling

Wall mount HooD InStallatIon

• Atleasttwoinstallersarerequiredduetotheweightand

sizeofthehood.

• Turnopowercircuitattheservicepanelbeforewiring

thisunit.

• Allelectricalworkmustbedonebyaqualiedelectrician

in accordance with all applicable codes and standards.

israngehoodmustbeproperlygrounded.

CAUTION

Figure3.

Figure1.

Figure2.

9Cyclone Canopy Installation - English

3 × Mounting Brackets

(Upper and Expandable Side)

HARDWARE PACKAGE

4 × Mounting Screws 4 × Washers 6 × Damper Screws 20 × Mounting Bracket Screws

SI520 ONLY

2 × Bottom Chimney Screws

ISLAND INSTALLATION - PARTS SUPPLIED

1 × Hood 1 × Chimney Flues

(Top and Bottom)

1 × Round Adapter

(May be Pre-Installed)

ISLAND INSTALLATION - TOOLS AND MATERIALS REQUIRED

• Electrical drill or ratchet driver

• ½” drill bit for drilling pilot holes

• 1 ¼” drill bit for drilling electrical wiring acess

hole (if applicable)

• Phillips screwdriver #2 or driver bit

• Wire stripper or cutter

• Tape measure

• Aluminum foil tape and/or duct tape

• Electrical supplies for wiring (i.e. marrets,

electrical tape)

• Hammer

• Jigsaw or saber saw

• Drywall stud (if applicable)

• Step latter

• Stud

• Level

PRE-INSTALLED

2 or 4 × G4 Type Lights

(12V, 20W)

1 × Oil Cup 1 × Plastic Damper Cover

PLEASE REFER TO PAGES 11-37 FOR YOUR MODEL’S SPECIFICATIONS

10 Cyclone Canopy Installation - English

Measure Installation Height

Determinetherequireddistancebetweentheceilingandthetopof

theblowerbox(D)baseduponceilingheight(C),desiredheightof

hoodabovecooktop(A)andunitheight(B):

D=C-A-B

e height D is the installation height of the mounting bracket

(Figure3).IftheinstallationheightDislessthan22”,themounting

bracketandductcoversmayneedtobecut.eductcoversneedsa

cleancutandmusttobecutfrombottomendsidesforbothinside

andoutsidepieces.Foroptimalclearance,theminimummounting

shouldbe30”abovethecookingsurface.

C/L

Blower Top Box

Range Hood Bottom

• When building framework, always follow all applicable

constructioncodesandstandards.

WARNING

Install Mounting Bracket

1. Modify ceiling structure at hood location. Install 2 × 4

crossframingbetweenceilingjoistsusingceilingmounting

bracketdimension(Figure4).eframeworkmustbesized

tosupportthetotalweightofthehood.

2. Finish ceiling surface. Be sure to mark the location of the

ceilingjoistsandcrossframing.Bringhousewiringthrough

nishedceiling.

10 ½”

11 ¼”

9 ⅝”

8 ¾”

ø 6 ¾”

3 ⅜”

4 ⅜”

1 ⅜”

Upper Mounting

Bracket

Ceiling Joists

Cross Framing

6” Round

Ductwork

ISlanD HooD InStallatIon

• Atleasttwoinstallersarerequiredduetotheweightand

sizeofthehood.

• ishoodshouldbeinstalledtoanishedceiling.

• Turnopowercircuitattheservicepanelbeforewiring

thisunit.

• Allelectricalworkmustbedonebyaqualiedelectrician

in accordance with all applicable codes and standards.

israngehoodmustbeproperlygrounded.

CAUTION

Figure4.

Figure5.

11Cyclone Canopy Installation - English

3. Positiontheceilingmountingplateinsuchawaythatoneof

thesideswiththreescrewholesfacesthefrontofthehood.

Secure mounting bracket to the ceiling using four wood

screws.Ensurethatscrewsaredrivenintothecenterofthe

framing for maximum strength.  Assemble two upper side

bracketstotheceilingmountingbracketusingsixmounting

screws(threeperbracket)(Figure5&6).

4. Use eight screws to mount the lower brackets to the upper

brackets. Determine lower brackets mounting height based

uponinstallationheightDofthemountingbracket.

Install the Island Hood

1. Removetheltersfromthehood;attachtheadapter/damper

tothetopofthehood.

2. Measure the required length of 6” round metal duct from the

adapter/damper to the ductwork rough-in in the ceiling.

Connectthissectionofducttotheadapter/damperandseal

jointwithmetalfoilducttape.

Mounting Screws

3. Slidethelowerandupperchimneyues

over the installed mounting bracket

andhaveasecondpersonholdittothe

ceiling.

4. Attachthehoodtomountingbracketusing

sixscrews(threeperside)(Figure7).

5. Slidethelowerandupperchimneyues

down on top of the hood.  Install the

electrical connection and connect the

duct to the rough-in duct work in the

ceiling. Seal the joints with metal foil

ducttape.

6. Power up hood and check for leaks

aroundducttape.

7. Carefully slide the upper (inner) ue

overuptotheceilingandsecureittothe

mountingplatefrombothsides.

8. Reinstalllterstothehood,peelothe

protectiveplasticlmcoveringtheues

andthehood.

Note: For some models, the “L” shape support frame may be

used (Figure 8). e installation procedures are same except

that the hood is mounted on one side. If need be, use an

adjustable string wire from other side to keep the hood level.

Figure6.

Figure7.

Figure8.

Note: 10 Feet Ceilings

ForSI520,usethemountingbracketsandductcoverssupplied.

For any other models, optional extension mounting brackets

andductcoversneedtobeordered.

12 Cyclone Canopy Installation - English

canopy HooDS SpecIfIcatIonS

WSC300/SC301/SC322/

SI323

SC500/SC501/SC502/

SC503/SC510/SC513/

SC514

SC707/SC712/SC717/

SC718/SC720/SC722/

SC727/SC771

SCB500/SCB501/

SCB514/SC711/SC715

SI520/SI521/SI522/

SI523/SI530/SI531

SIZE 30”/36” 30”/36”

SC500/SC514-24”/30”/36” 30”/36” 30”/36” 36”

SI523-30”/36”

MOUNTING WALL

SI323-ISLAND WALL WALL WALL ISLAND

MAX.

CUBIC FEET/METER

(CFM)

300 550 550 550 550

MAX. SONES 2.5 6666

FINISH STAINLESSSTEEL

STAINLESSSTEEL+GLASS

STAINLESSSTEEL

STAINLESSSTEEL+GLASS

STAINLESSSTEEL

STAINLESSSTEEL+GLASS

STAINLESSSTEEL

STAINLESSSTEEL+GLASS

STAINLESSSTEEL

STAINLESSSTEEL+GLASS

CONTROLS PUSHBUTTON PUSHBUTTON PUSHBUTTON PUSHBUTTON PUSHBUTTON

SPEED LEVELS 33333

DELAY OFF YES YES YES YES YES

LIGHTING 2×12V20W

HALOGEN

2×12V20W

HALOGEN

2×12V20W

HALOGEN

2×12V20W

HALOGEN

2×12V20W

HALOGEN

FILTERS ALUMINUMMESH ALUMINUMMESH ALUMINUMMESH BAFFLE ALUMINUMMESH

EXTENSION DUCT

OPTION

YES,10’+CEILING

SPECIALORDER

YES,10’+CEILING

SPECIALORDER

YES,10’+CEILING

SPECIALORDER

YES,10’+CEILING

SPECIALORDER

YES,10’+CEILING

SPECIALORDER

DUCT 6”ROUNDTOP 6”ROUNDTOP 6”ROUNDTOP 6”ROUNDTOP 6”ROUNDTOP

AC INPUT 120V

60Hz

120V

60Hz

120V

60Hz

120V

60Hz

120V

60Hz

POWER

CONSUMPTION

170W

2.5A

280W

2.5A

280W

2.5A

280W

2.5A

280W

2.5A

MOUNTING HEIGHT 28”-36” 28”-36” 28”-36” 28”-36” 28”-36”

13Cyclone Canopy Installation - English

3 1/4”

Φ 6”

29 ½” or 35 ½”

9 ¼”

1 ¾”

8”

17 ¾”

10 ¼”

Min. 27 ¾”

Max. 45 ¼”

6 ¼”

7 ⅛”

11 ½”

13”

6 ¾”

3 1/4”

FRONT SIDE

TOP BACK

8”

9 ¼”

18 ½”

30”/36”

1 ¾”

10 ¼”

27 ¾”

Max 45 ¼”

17 ¾”

SpecIfIcatIonS

Alito Collection Wall Mount - Model: SC(B)500

14 Cyclone Canopy Installation - English

3 1/4”

Φ 6”

23 ½”

9 ¼”

1 ¾”

8”

17 ¾”

10 ¼”

Min. 27 ¾”

Max. 45 ¼”

6 ¼”

7 ⅛”

11 ½”

13”

6 ¾”

3 1/4”

FRONT SIDE

TOP BACK

8”

9 ¼”

18 ½”

23 ½”

1 ¾”

11”

27 ¾”

Max 45 ¼”

17 ¾”

SpecIfIcatIonS

Alito Collection Wall Mount - Model: SC50024

15Cyclone Canopy Installation - English

SpecIfIcatIonS

Alito Collection Wall Mount - Model: SC(B)501

FRONT SIDE

TOP BACK

7 ¾”

10 ½”

Min. 23 ½”

Max. 44 ½”

Min. 23 ½”

Max. 44 ½”

29 ½” or 35 ½”

23 ¼”

19 ¾”

17”

7 ½”

9 ½”

12”

13 ¾”

5 ¼”

3 ¼”

Φ 6”

11 ¾”

21 ½”

11 ¾”

10 ½”

19 ¾”

30”/36”

2 ½”

17”

23 ½”

Max: 44 ½”

16 Cyclone Canopy Installation - English

FRONT SIDE

TOP BACK

7 ¾”

9 ½”

12”

5 ¼”

3 ¼”

Φ 6”

7 ½”

11 ¾” 10 ½”

29 ½” or 35 ½” 19 ¾”

13 ¾”

Min. 23 ½”

Max. 44 ½”

23 ¼” 17”

1 ¾”

10 ½”

11 ¾”

21 ½”

2”

30”/36”

19 ¾”

23 ½”

Max: 44 ½”

SpecIfIcatIonS

Alito Collection Wall Mount - Model: SC(B)502

17Cyclone Canopy Installation - English

SpecIfIcatIonS

Alito Collection Wall Mount - Model: SC(B)503

FRONT SIDE

TOP BACK

7 ¾”

9 ½”

12”

5 ¼”

3 ¼”

Φ 6”

7 ½”

11 ¾” 10 ½”

29 ½” or 35 ½” 19 ¾”

13 3/4”

Min. 23 ½”

Max. 44 ½”

23 ¼” 17”

1 ¾”

10 ½”

11 ¾”

21 ½”

2”

30”/36”

19 ¾”

23 ½”

Max: 44 ½”

18 Cyclone Canopy Installation - English

SpecIfIcatIonS

Alito Collection Wall Mount - Model: SC510

FRONT SIDE

TOP BACK

7 ¾”

9 ½”

12”

5 ¼”

3 ¼”

Φ 6”

7 ½”

11 ¾” 10 ½”

29 ½” or 35 ½” 19 ¾”

13 ¾”

Min. 23 ½”

Max. 44 ½”

1 ¾”

5 ¼”

6 ¼”

14 ½”

1 ¾”

10 ½”

11 ¾”

21 ½”

30”/36”

19 ¾”

23 ½”

Max: 44 ½”

19Cyclone Canopy Installation - English

SpecIfIcatIonS

Alito Collection Wall Mount - Model: SC(B)513

FRONT SIDE

TOP BACK

7 ¾”

9 ½”

13 ½”

5 ¼”

3 ¼”

Φ 6”

7 ½”

11 ¾” 10 ½”

29 ½” or 35 ½” 19 ½”

15 ¼”

Min. 24 ½”

Max. 45 ½”

16 ½”

1 ½”

24 ¼”

1 ½”

10 ½”

11 ¾”

21 ½”

30”/36”

19 ½”

24 ½”

Max: 45 ½”

20 Cyclone Canopy Installation - English

SpecIfIcatIonS

Alito Collection Wall Mount - Model: SC(B)514

FRONT SIDE

TOP BACK

7 ¾”

9 ½”

13 ¼”

5 ¼”

3 ¼”

Φ 6”

7 ½”

11 ¾” 10 ½”

29 ½” or 35 ½” 19 ½”

15”

Min. 23 ½”

Max. 44 ½”

2 ¾”

10 ½”

11 ¾”

21 ½”

30”/36”

19 ½”

23 ½”

Max 44 ½”

Page is loading ...

CyClone SC502 Installation And Operation Instructions Manual

Brand: CyClone

Model: SC502

Category: Cooker hoods

Type: Installation And Operation Instructions Manual

This manual is also suitable for

Download PDF

report

CyClone SC502 Installation And Operation Instructions Manual

This manual is also suitable for

CyClone SC502 Installation And Operation Instructions Manual

Related papers

Other documents