Toro Snow Thrower Power Kit, TX 427, TX 525, or TX 1300 Compact Tool Carrier Installation guide

Type
Installation guide
Form No. 3463-419 Rev A
Snowthrower Power Kit
TX 427, TX 525, or TX 1300 Compact T ool Carrier
Model No. 144-2512
Installation Instructions
Installation
Loose Parts
Use the chart below to verify that all parts have been shipped.
Description
Qty .
Use
No parts required
Remove the fuse panel.
No parts required
Remove the existing USB socket.
No parts required
Install the 12V receptacle.
Electric accessory port 1
Splitter wire harness
1
Wire harness kit (TX 1300 only)
1
Install the wire harnesses.
Preparing the Machine
1. Park the machine on a level surface.
2. Lower the loader arms.
3. Shut of f the engine and remove the key .
4. Open the hood and secure it with the prop rod.
© 2023—The T oro® Company
81 1 1 L yndale A venue South
Bloomington, MN 55420 Register at www .T oro.com.
Original Instructions (EN)
Printed in the USA
All Rights Reserved
*3463-419*
Removing the Fuse Panel
TX 525 Only
1. Pull the hairpin cotter from the bottom end of the
hood prop-rod and slide the prop rod out of the
retaining brackets and the prop-rod tab.
g004984
Figure 1
1. Prop-rod tab 4. Retaining
bracket—bottom
2. Retaining bracket—top 5. Hairpin cotter
3. Prop rod
2. Remove the 4 screws securing the fuse panel
and then pull the panel out and up to remove it.
g004985
Figure 2
1. Fuse panel
2. Screw
Removing the Existing USB
Socket
TX 1300 Only
1. Remove the 4 screws (1/4 inch) securing the
control plate to the main frame.
g454386
Figure 3
2. Move the control plate out of the frame.
3. Remove the black and white wires secured to
the USB connector .
g454385
Figure 4
4. Loosen the retainer nut and remove the USB
socket from the control plate.
2
Installing the 12V Receptacle
W ARNING
Using a drill without proper eye protection may allow debris to enter the eye, causing injury .
When drilling or carrying out other operation, always wear eye protection.
1. TX 427 and TX 525 machines only: Mark and drill a hole (1-5/32 inch diameter) into the control in the
location shown below .
Note: If you do not have a 1-5/32 inch drill bit, use a 1-1/8 inch drill bit to drill the hole and then grind
the hole to expand it.
g331 1 19
Figure 5
TX 427
g331 151
Figure 6
TX 525
2. Remove the locking ring from the 12V receptacle.
3
3. Install the 12V receptacle in the hole and secure it with the locking ring.
g331 165
Figure 7
1. Locking ring 2. 12V receptacle
Installing the W ire Harnesses
g333594
Figure 8
1. Wire harness installed on TX 427 2. Wire harness installed on TX 525
1. Install the post connectors from the port wire harness to the posts on the 12V receptacle.
g31 1406
Figure 9
1. Negative (-) connector 3. Positive (+) connector
2. Negative (-) post 4. Positive (-) post
2. Connect the port wire harness to an outgoing power connector (end with 2 connectors) of the splitter
harness.
4
g331 130
Figure 10
1. Port wire harness
3. Splitter harness
2. Outgoing power connectors 4. Accessory connector of machine wire harness
3. Connect the other end of the splitter harness to an accessory connector on the machine wire harness.
Note: If no connectors are open on the machine wire harness, unplug an accessory from the machine
wire harness and plug it into the other outgoing power connector of the splitter harness.
4. TX 525 machine only: Install the fuse panel.
Note: Reverse the procedure for Removing the Fuse Panel ( page 2 ) .
5. TX 1300 machine only: Install the control plate and secure it with the 4 screws (1/4 inch).
g454386
Figure 1 1
6. Close the hood.
7. TX 1300 machine only: Connect the new wire harness kit to the snowthower and the wire harness
coming from the control box. Refer to the snowthower Operator ’ s Manual .
5
Notes:
Notes:
  • Page 1 1
  • Page 2 2
  • Page 3 3
  • Page 4 4
  • Page 5 5
  • Page 6 6
  • Page 7 7
  • Page 8 8

Toro Snow Thrower Power Kit, TX 427, TX 525, or TX 1300 Compact Tool Carrier Installation guide

Type
Installation guide

Ask a question and I''ll find the answer in the document

Finding information in a document is now easier with AI