DKS Smart Gate Controller User's User manual

DKS
Brand
DKS
Model
Smart Gate Controller User's
Type
User manual

This manual is also suitable for

DKS SMART GATE CONTROLLER
• DO NOT let children use or play with the Smart Gate device or App.
• ONLY operate your Smart Gate device when you are in clear view of your gate, and you have verified that there are no objects
obstructing the operation of the gate.
• ALWAYS wait for the gate to complete its cycle before leaving the area.
• This device complies with Part 15 of the FCC Rules. Operation is subject to the following two conditions:
(1) this device may not cause harmful interference, and
(2) this device must accept any interference received, including interference that may cause undesired operation.
Monitor and control your gate from anywhere. With the combined power of the DKS Smart Gate Controller, Smart Connect
App, and your existing WiFi connection, you can open and close your gate from anywhere — right on your smartphone.
Simply wire the Smart Gate Controller to any gate operator that has a built-in reply switch (or USER SUPPLIED gate
position switch) and your existing WiFi.
WARNING!
Smart Gate
Model: 1800-500
Contains FCC ID: 2ANDL-CB2S
WI-FI: IEEE 802.11b/g/n
Input: AC/DC8-30V
Output: NO
Output
Input
ON/OFF
DOO
RKI
N
G
®
®
DoorKing Part Number
1800-500
Copyright 2023 DoorKing®, Inc. All rights reserved.
120 S. Glasgow Avenue
Inglewood, California 90301 U.S.A.
Table of Contents
Set up your DKS Smart Connect account
Preparation Before Final Installation
Add Smart Connect Device to DKS Smart Connect app
Install your DKS Smart Gate Controller
DKS Smart Connect App
Link DKS Smart Connect account to Alexa
Link DKS Smart Connect account to Google Home
Set Up Siri to Control the DoorKing Smart Gate
2
2
2
3-5
6
7
8
9
Can be linked to personal networks for voice activation:
Hey Google, open the DoorKing Smart Gate.
Hey Google, close the DoorKing Smart Gate.
Alexa, open the DoorKing Smart Gate.
Alexa, close the DoorKing Smart Gate.
Hey Siri, open the DoorKing Smart Gate.
Hey Siri, close the DoorKing Smart Gate.
1
1800-065-D-10-23
First, download DKS Smart Connect app for your iOS or Android device.
Make sure you have the latest version of DKS Smart Connect
from the app store.
First, Check your WI-FI signal strength at gate operator (2.4 Ghz ONLY)
Check the Wi-Fi signal where the Smart Gate Controller
will be installed using your smart phone.
If you’re new to DKS Smart Connect, tap Sign UP to create an account. Enter your e-mail address,
then tap Get Verification Code, enter the code you receive in your e-mail to set up the Password.
If you already have an DKS Smart Connect account used for other devices, tap Log in with Existing Account.
Turn on smart phones bluetooth and Connect smartphone to your home WI-FI network BEFORE the following steps.
Have your SSID WiFi name ready, with WiFi password if asked.
Android: Settings – Apps – Select DKS Smart – Permissions: Make sure “nearby devices”, is listed under Allowed.
I-Phone: Settings-Privacy & Settings – Bluetooth – DKS Smart needs to show enabled.
Next, create your account.
At the installation location, power up the Smart Gate Controller
by connecting it to an 8-30V power source (AC/DC) (see pages 4-5).
The device’s LED will blink.
Next, Power up your Smart Gate Controller.
Smart Gate
Model: 1800-500
Contains FCC ID: 2ANDL-CB2S
WI-FI: IEEE 802.11b/g/n
Input: AC/DC8-30V
Output: NO
Output
Input
ON/OFF
F
F
F
F
F
F
F
F
F
F
F
F
F
F
F
F
F
F
F
F
F
F
F
F
F
F
F
F
F
DOO
RKI
N
G
®
®
DKS Smart
Connect
Set up your DKS Smart Connect account
Add Smart Connect Device to DKS Smart Connect app
12
34
Preparation Before Final Installation
IMPORTANT
Wi-Fi
Signal
Strength
Launch the app and tap the
Plus (+) in the top right
corner to add a device.
Press ON/OFF Button
until LED flashes. Tap
(Add) on your phone.
Enter your Wi-Fi name
and password, then tap
Confirm.
Now your DoorKing Smart
Gate has been successfully
added to DKS Smart
Connect app. Tap Done.
NOTE: if LED is NOT flashing,
press and hold the ON/OFF button
for 8 seconds (Until it flashes)
NOTE:
If device does not show under
discovered devices, press and hold the
button on the device for about 8 seconds
(Until LED flashes red). Make sure DKS
Smart app has access for nearby devices.
DO NOT install the DKS Smart Gate Controller if the Wi-Fi signal is unacceptable.
Make sure DKS Smart Connect has access to nearby devices from your cell phone.
Make sure gate operator’s
power has been turned
OFF BEFORE wiring to it.
Smart Gate
Model: 1800-500
Contains FCC ID: 2ANDL-CB2S
WI-FI: IEEE 802.11b/g/n
Input: AC/DC8-30V
Output: NO
Output
Input
ON/OFF
F
F
F
F
F
F
F
F
F
F
F
F
F
F
F
F
F
F
F
F
F
F
F
F
F
F
F
F
F
F
DOO
RKI
N
G
®
®
Blue
Red
Black Yellow
Relay
Contact
Power
+
-
Relay
Output
2
1800-065-D-10-23
Relay
Contact
Blue
Tesa Tape
Sensor
Mounting Brackets
Waterproof Enclosure
(not provided)
Nail Wire Clips / Screws / Bolts & Nuts
Cable Clip
Holders
Black -
Red +
Power _
+
Relay
Output
Yellow
ON / OFF
Switch
LED
Install your DKS Smart Gate Controller
Kit Includes:
POWER OFF your existing gate operator BEFORE installation
Gate Position Switch (User Supplied)
The DKS Smart Gate Controller’
s signal is impeded by metal. Make sure that the place where you are installing it has a strong
Wi-Fi signal (see previous page
“Preparation Before Installation”).
The operator cover can also diminish the signal. If the controller is being installed
INSIDE the operator, test it with the operator
cover on and see if signal strength is acceptable
.
NOTE: In the app, you can check wireless signal strength, “Check Device Network”
DoorKing’s recommendation is 67dbm or below. The cell phone must be connected to same
Wi-Fi as the DKS Smart Gate Controller.
If the controller is installed
OUTSIDE the operator, make sure to use a waterproof plastic box
(not provided) to protect the controlle
r.
After you are satisfied with the Wi-Fi signal strength in the location where you are installing your
DKS Smart Gate Controlle
r, find your specific DoorKing operator on the next 2 pages to show
how to wire the controller to it.
Smart Gate
Model: 1800-500
Contains FCC ID: 2ANDL-CB2S
WI-FI: IEEE 802.11b/g/n
Input: AC/DC8-30V
Output: NO
Output
Input
ON/OFF
DOO
RKI
N
G
®
®
Zip Ties
Smart Gate
Model: 1800-500
Contains FCC ID: 2ANDL-CB2S
WI-FI: IEEE 802.11b/g/n
Input: AC/DC8-30V
Output: NO
Output
Input
ON/OFF
DOO
RKI
N
G
®
®
Without a gate open position switch connected to the blue wires, the Smart Gate Switch
WILL NOT be able to provide informa-
tion as to whether the gate is open or closed. Use the built-in relay that is available on ever
y DKS gate operator circuit board to
provide the gate open indication to the Smart Gate Switch (see pages 4-5).
Note:
The relay jumper on the DKS gate operator circuit board is set to NC (Normally Closed), and the relay is set to activate
when the
gate reaches the full open position.
Other brand gate operators may have the same type of relay connection available. Check the manufacturer's installation manual
for information.
If a gate open relay is
NOT available, a separate switch (user supplied) will need to be wired to the Smart Gate Switch, otherw
ise
the position of the gate
WILL NOT be available on the app.
IMPOR
TANT: The gate open switch MUST be wired Normally Closed. When the gate reaches the full open position, the
switch opens.
3
1800-065-D-10-23
ON
ON
REVERSE
SENSITIVITY
REVERSE
LOOP
EXIT
LOOP
KEY SWITCH
4602
SW1SW2
OPEN
TIMER
NC
1
2
3
4
5
NO
18
17
16
15
14
13
12
11
10
9
8
7
6
5
4
3
2
1
20
19
18
17
16
15
14
13
12
11
10
9
8
7
6
5
4
3
2
1
NC
NO
1
ON
2 3 4 5 6 7 81
ON
2 3 4 5 6 7 8
12345687
4502
6050, 6100, 6300 Swing Gate Operators9100, 9150 Slide Gate Operators
Power
Relay
Yellow
Blue
Red
Black
Relay
Contact
Com
6050
6100
6300
9100
9150
Set Jumper to NC
Set Jumper to NC
Smart Gate
Model: 1800-500
Contains FCC ID: 2ANDL-CB2S
WI-FI: IEEE 802.11b/g/n
Input: AC/DC8-30V
Output: NO
Output
Input
ON/OFF
DOO
RKI
N
G
®
®
Alternate
Wiring
Yellow
Yellow
Red
Power
Relay
Yellow
Blue
Red
Black
Relay
Contact
Com
Smart Gate
Model: 1800-500
Contains FCC ID: 2ANDL-CB2S
WI-FI: IEEE 802.11b/g/n
Input: AC/DC8-30V
Output: NO
Output
Input
ON/OFF
DOO
RKI
N
G
®
®
Full Open
Partial Open
1
ON SW 1
2 3 4 1
ON SW 2
REVERSE
LOOP
P2 P8
EXIT
LOOP
SELF
TEST
NC
TIME
DELAY
REV SENSEREV SENSE
1
2
3
4
5
6
7
8
9
13
12
11
10
14
15
16
17
18
19
20
2 3 45 6 7 8
NO
4405
20 19 18 17 16 15 14 13 12 11 10 9 8 7 6543 2 1
6500 Series Swing Gate Operators,
9000 Slide Gate Operators
9000
6500
Com
24 Volt
Relay
3-Pin Remote
Terminal
123
Alternate
Wiring
Yellow
Yellow
Red
Com
24 Volt
Relay
3-Pin Remote
Terminal
123
12345678
ON
12345678
ON
20
19
18
17
16
15
14
13
12
11
10
9
8
7
6
5
4
3
2
1
EXIT
LOOP
REVERSE
LOOP
POWER SEL
AC POWER/SOLAR
REV SENSE
P3
SELF TEST
RESET
RED=CHARGING
GREEN=CHARGED
KEY
SWITCH
NO
NC
NC
3 BUTTON
CONTROL
SW1
SW2
OFFON
POWER
P4
P2
16
TIME DELAY
4100
12345678910
1234
ON
OPEN BEAM
CLOSE BEAM
OPEN EDGE
CLOSE EDGE
AC Powered 6524 Swing Gate Operators,
AC Powered 9024 Slide Gate Operators
9024
6524
AC Powered ONLY
Set Jumper to NC
Power
Relay
Yellow
Blue
Red
Black
Relay
Contact
Com
Power
Relay
Yellow
Blue
Red
Black
Relay
Contact
Com
Smart Gate
Model: 1800-500
Contains FCC ID: 2ANDL-CB2S
WI-FI: IEEE 802.11b/g/n
Input: AC/DC8-30V
Output: NO
Output
Input
ON/OFF
DOO
RKI
N
G
®
®
Smart Gate
Model: 1800-500
Contains FCC ID: 2ANDL-CB2S
WI-FI: IEEE 802.11b/g/n
Input: AC/DC8-30V
Output: NO
Output
Input
ON/OFF
DOO
RKI
N
G
®
®
Not for use with the SOLAR Powered 6524 or 9024.
Set Jumper to NC
Make sure gate operator’s
power has been turned
OFF BEFORE wiring to it.
Make sure gate operator’s
power has been turned
OFF BEFORE wiring to it.
ON
12345678
SW 1
#4-OFF
#5-OFF
ON
12345678
SW 4
#1-OFF
#2-OFF
#6-OFF
#7-OFF
ON
12345678
SW 1
#7-OFF
#8-OFF
SW 1
1
ON
2 3 4 5 6 7 8
4
1800-065-D-10-23
6004, 6006, 6400 Swing Gate Operators
123456 7 8910 11 12 13 14 15 16 17 18 19 20
4302
FULL
OPEN
OB
CB
Close
Beam
Open
Beam
GND
GND
SW1
1
ON
2
1476-010
Power
Relay
Yellow
Blue
Red
Black
Relay
Contact
Com
Smart Gate
Model: 1800-500
Contains FCC ID: 2ANDL-CB2S
WI-FI: IEEE 802.11b/g/n
Input: AC/DC8-30V
Output: NO
Output
Input
ON/OFF
DOO
RKI
N
G
®
®
Set Jumper to NC
6004
DOORKING
CLASS
CERTIFIED TO
CAN/CSA C22.2 NO. 247
CONFORMS TO
ANSI/UL-325
VEHICULAR GATE OPERATOR
HP
53382
MODEL
SERIAL
VOLTSPHASE
AMPS 60 Hz
MAX GATE LOAD
DoorKing, Inc., Inglewood, CA
6400
6006
4404-010
TIME
DELAY
EXIT
LOOP
LMT
LMT
REVERSE
LOOP
REV SENSE
OPEN
1
ON
2 3 41
ON
2 3 4 5 6 7 8
NC
P8 P7P6
NO
20 19 18 17 16 15 14 13 12 11 10 987654321
4404
9200 Series,
9500 Slide Gate Operators
9200
9500
Set Jumper to NC
N
Partial Open
Power
Relay
Yellow
Blue
Red
Black
Relay
Contact
Com
Com
Smart Gate
Model: 1800-500
Contains FCC ID: 2ANDL-CB2S
WI-FI: IEEE 802.11b/g/n
Input: AC/DC8-30V
Output: NO
Output
Input
ON/OFF
DOO
RKI
N
G
®
®
LIMIT
LIMIT
PA RT
TIME
DELAY
REV SENSE
CLOSE
REV SENSE
OPEN
1
ON
2 3 41
ON
2 3 4 5 6 7 8
NC
NO
EXIT
LOOP
REVERSE
LOOP
GATE FORCED
20 19 18 17 16 15 14 13 12 11 10 9 8 76 5 4 321
4402
REVERSE
SENSITIVITY
TIME
DELAY
POWER
1
ON
23456781
ON
2 3 4 5 6 7 8
NC
UP
LOOP
DOWN
LOOP
12345678910 11 12 13 14
1601
1601, 1602, 1603 Barrier Gate Operators
1175 Overhead Gate Operator
Power
Relay
Yellow
Blue
Red
Black
Relay
Contact
Arm Relay Contact:
Com-N.C.
Relay
Contact
Com
NO
CNCNO
Smart Gate
Model: 1800-500
Contains FCC ID: 2ANDL-CB2S
WI-FI: IEEE 802.11b/g/n
Input: AC/DC8-30V
Output: NO
Output
Input
ON/OFF
DOO
RKI
N
G
®
®
Set Jumper to NC
Power
Relay
Yellow
Blue
Red
Black
Relay
Contact
Com
Com
Smart Gate
Model: 1800-500
Contains FCC ID: 2ANDL-CB2S
WI-FI: IEEE 802.11b/g/n
Input: AC/DC8-30V
Output: NO
Output
Input
ON/OFF
DOO
RKI
N
G
®
®
1600
1175
Make sure gate operator’s
power has been turned
OFF BEFORE wiring to it.
Make sure gate operator’s
power has been turned
OFF BEFORE wiring to it.
#1-OFF
#2-OFF
SW 2
1
ON
23 4
#5-OFF
#4-OFF
SW 1
1
ON
2345678
SW 1 is Upside-Down on Board
SW 1
1
ON
2 3 4 5 6 7 8
#8-OFF
#7-OFF
5
1800-065-D-10-23
Main Screen
DKS Smart Connect App
Function Description of the Operation Inter
face
Name your smart switch, along with other options.
• Select your added device to control your gate or to edit:
• Device can be removed from here.
• Select to make adjustment as described below.
NOTE: These items are only available when logged in as the PRIMARY user.
Shows gate status: Open or Closed (status relay or user supplied gate position switch must be connected)
Only Available when gate operator’s timer is On and enabled from app settings
“Is your gate timer enabled.”
If gate operator’s timer is Off, close will close gate from previous “Open” command.
If gate operator’s timer is On, you will use “Close” to close from a previous “Hold Open” command.
If gate operator’s timer is Off, select “Open” to open gate or “Close” to close gate.
If gate operator’s timer is On, timer from operator will auto close gate.
Setup: Open/Close Notifications, If gate timer is enabled, Gate run time, Voice control
View Open/Close history log with date and time.
Create auto open/close times by dates.
Name or rename your smart switch.
View smart switch IP address, MAC address, WiFi signal strength.
Not Used
Link to your smart voice assistant devices.
Enable notification to phone, if device stays offline for over 30 minutes.
Share device to others, by SMS text or e-mail.
Select your gate operating closing settings:
If gate operator is set to time out and close- Move slider to the right enable (Yes)
If gate operator’s timer to close is off – Move slider to – left disable (No)
Enable/Disable notifications to cell phone.
Enable voice assistant devices (Alexa, Google).
Create a fast shortcut to desktop showing the name of the switch.
Check WiFi signal to switch (Cell phone must be connected to the same
network as the switch), reading should be no higher than – 67 dbm
Not Used
Set gate limit timing so if not reached after the set time, a warning message will pop up.
Set for Google Assistant if used.
- Create a beginning time with days the gate should go open.
- Create an end time with days the gate should go back to close
DoorKing Smart Gate
Edit name and other options:
Settings:
Histor
y:
Schedule:
• Select to make adjustment as described below.
• Select to view log history of Open/Close/Hold Open events with Date and Time.
• Select to select Auto Open/Close Time.
6
1800-065-D-10-23
Link DKS Smart Connect account to Alexa
Launch Amazon Alexa app and tap More....
Enter the e-mail used when installing DKS
Smart Connect, select Next Step from the
option of apps.
Select the skill, then Enable To Use and “Agree and Link”.Then tap Skills & Games
and search for Smart Life....
Before Linking DKS Smart Connect to Alexa:
• Launch DKS Smart Connect App, tap “DoorKing Smart Gate”.
• Tap the Ring Bell in the bottom LEFT corner.
• Tap “Set Password”.
• Enter a Password, then tap “Confirm”.
NOTE: If Alexa responds that it cannot open multiple devices, delete one of the multiple devices.
Select DKS Smart then select Link
Devices for this App Account.
You will be prompted to enter the password you
setup originally when installing DKS Smart
Connect. Select Next Step,then select Authorize.
Select Close, Alexa will start looking for devices
to connect. This will take from seconds to
minutes, once complete select close.
You will be asked to create a 4-digit
code, enter the same 4 digit-code you
created from DKS Smart Connect,
select Next.
Enter your Amazon account password.
Select Next to complete “open by voice
setup”. At this point will have the option
to organize your device to a group, or
select Skip, then Done.
1
2
3
7
1800-065-D-10-23
Link DKS Smart Connect account to Google Home
Before Linking DKS Smart Connect to Google Home:
• Launch DKS Smart Connect App, tap “DoorKing Smart Gate”.
• Tap the Ring Bell in the bottom LEFT corner.
• Tap “Set Password”.
• Enter a Password, then tap “Confirm”.
Tap on to type and search....
“Smart Life”
Enter the email you setup or
used from the DoorKing
Smart Connect app....
A list of apps will be listed, select
DKS Smart, Then tap Link
devices for this App account....
Enter the e-mail passwords
then select Next Step.
Launch Google Home app.... Devices-Add Device.... Tap on Works with Google.
1
2
Select DoorKing Smart Gate or
the name you setup for the
device,then select Add to room...
You can then select any room from
the list or add one, select Next, You
are now finish, select Done, close
Google Home.
3Tap on Authorize to allow
linking permission....
8
1800-065-D-10-23
Siri can only be used when logged as primar
y user
Log in the
“DKS Smart Connect” app:
Select “Scene” at
the bottom.
Tap “+”. Select
“Launch Tap To Run”.
Select “Run the device”.Select “Add Task”. Select “DoorKing
Smart Gate (Default
device name)”, then
select “Action”, then
select “Open” or
“Close”. Click “Save
”,
Click “Next
”, and click
“Save” again (please
note Siri cannot
support control “Hold
Open”.
Set Up Siri to Control the DoorKing Smart Gate
Go back to “Scene” page,
tap on “Add to Siri”.
Select the tab “DoorKing Smart Gate”,
action: Open or Close.
Select “Done”. Now you can say
“the magic word” to control the
DoorKing Smart Gate.
9
1800-065-D-10-23
  • Page 1 1
  • Page 2 2
  • Page 3 3
  • Page 4 4
  • Page 5 5
  • Page 6 6
  • Page 7 7
  • Page 8 8
  • Page 9 9

DKS Smart Gate Controller User's User manual

DKS
Brand
DKS
Model
Smart Gate Controller User's
Type
User manual
This manual is also suitable for
Download PDF
report

Ask a question and I''ll find the answer in the document

Finding information in a document is now easier with AI

Related papers

Other documents