TrailFX PFFG3001T Installation guide

Type
Installation guide
www.TrailFX.com
Page 1 of 6 Rev 091818
TO AVOID BEING SCRATCHED, PLEASE PROTECT THE SURFACE OF
THE FENDER FLARE CAREFULLY.
REMOVE CONTENTS FROM BOX. VERIFY ALL PARTS ARE PRESENT.
READ INSTRUCTIONS CAREFULLY BEFORE STARTING INSTALLATION.
60-180 min
support@trailfx.com
1 866 638 4870
Limited Lifetime Warranty
Cutting Not
Required
PLEASE USE SAFETY GLASSES & ENSURE TO BLOCK VEHICLE
MOVEMENT DURING INSTALLATION PROCESS
IMPORTANT: DO NOT OVER-TIGHTEN THE MOUNTING SCREWS.
OVER-TIGHTENING THE SCREWS WILL RESULT IN STRESS FRACTURES.
KIT INCLUDES
Qty
Qty
Part Description
2 ea.
8 ea.
S brackets (F)
2 ea.
8 ea.
Phillips head screws 8x1/4” (G)
48 ea.
6 ea.
Speed clips (H)
48 ea.
6 ea.
8x ¾” mounting screw (I)
1 ea.
TOOLS NEEDED
Stubby Ratchet
Utility knife
7/32 socket
2mm Phillips head bit
Drill and 1/16 drill bit
Phillips head screw driver
13mm socket with extension
4.5mm Hex key
Fender Flare
PFFG3001T / PFFG3001S
2007 - 2013: GMC Sierra 1500
Drilling
Required
www.TrailFX.com
Page 2 of 6 Rev 091818
PRIOR TO INSTALLATION
Read these instructions before beginning the installation
Make sure kit is complete before beginning installation
Ensure you have the correct TrailFX fender flares for your vehicle before beginning the installation process.
NOTE: The flares are embossed with either a D or P indicating Passenger or Driver. Make sure you match the correct flare to
the side of the vehicle you are installing.
If you plan on painting your fender flares it must be done prior to installation. All surfaces must be cleaned and prepped following
the specifications outlined by the paint manufacturer.
PLEASE NOTE: Painted flares cannot be returned.
STEP 1
INSTALLTION OF BUTTON HEAD STAINLESS STEEL BOLTS
Locate the supplied Button head stainless steel bolts, and nylon jam nuts. Install one Button head stainless steel bolts in one
of the holes in the recess of the flares as shown below in the Fig. a
Proceed to the inside of the flare. Place a nylon jam nut on the threads of the Button head stainless steel bolts and tighten.
Use a 13mm socket with an extension and a 4.5mm Hex key as shown in . Fig. b and c to complete the task.
Note: These bolts are decorative only and are not intended for securing the flares
INSTALLING RUBBER TRIM ON NEW FENDER FLARES
Install the rubber edge trim on the outer edge of the fender flare. The outer edge is the side that comes into contact with the
vehicle’s fender. It DOES NOT get installed on the inner edge of the fender flare.
Fig a
Fig b
Fig c
www.TrailFX.com
Page 3 of 6 Rev 091818
Step 1
Locate the supplied rubber edge trim (E). Peel back approx. 2” of the red lining. Starting at one end of the flare, push the
trim onto the edge of the flare. Fig 1
NOTE: Make sure the red liner sits inside the flare.
Continue pressing the rubber trim onto the flare in 6” increments. Fig 2
Step 2
Peel back 6 inches of the red liner. Fig 3
Firmly press the trim to bond to the flare. Repeat steps 1-4 until you have gone completely around the flare. Repeat this
process for the remaining flares. Fig 4
REMOVING FRONT FACTORY SCREWS
Step 1
Proceed to the inside of the vehicle wheel well.
Using a 10mm socket locate and remove 6 factory bolts on the inner wall of the wheel well lip. Set factory
hardware aside for later use.
www.TrailFX.com
Page 4 of 6 Rev 091818
INSTALLING FRONT FENDER FLARES
INSTALLING REAR FENDER FLARE
Step 1
Place front flare (A) onto vehicle. Line up the
holes in the flare with the holes in the inner wheel
well.
Step 2
Reinstall factory hex head screws onto all six positions as
shown. Repeat step 1-2 for other side front fender.
Step 1
With help from an assistant place the flare onto the vehicle.
Adjust the flare for best fit. Using the pilot holes in the flare
as a guide place a mark on the lip of the wheel well.
Remove flare from vehicle. Set flare aside in a protected
area.
Step 2
Place a piece of masking tape on the wheel well lip over the
previously made marks. Slide a supplied S bracket over the
taped areas.
www.TrailFX.com
Page 5 of 6 Rev 091818
INSTALLING REAR FENDER FLARE
Step 4
Place fender (A) back onto vehicle. Line up the holes in the
fender flare with the S brackets. Place supplied Philips head
screw #8x1/4” (G) through the hole in the fender flare and onto S
bracket. Tighten down using a #2 Phillip’s head screw driver.
Repeat step for remaining Phillip’s head screw. Repeat step 1-3
for other side rear fender.
Step 3
Slide a supplied speed clip (H) onto the vehicle as
shown. Line up the speed clip hole with the factory holes
on the inner wheel well lip. Repeat step for remaining
speed clips.
Step 5
Place supplied Philips head screw #8x ¾” (I) through the hole in the fender flare and onto the speed clip (H). Tighten down
using a #2 Phillip’s head screw driver. Repeat step for remaining Phillip’s head screw. Repeat step 1-5 for other side rear
fender.
www.TrailFX.com
Page 6 of 6 Rev 091818
PRODUCT CARE
1. Periodically check the product to ensure all fasteners are tight and components are intact.
2. Regular waxing is recommended to protect the finish of the product.
Check out these other TrailFX Products!! www.TrailFX.com
FAQ’s
1. Fender flares are loose after installation.
Please ensure that all required mounting brackets / hardware’s are installed & tighten correctly.
2. Missing / Excess Hardware.
Re-check hardware count as per the part list.
Keystone Automotive Operations Inc. (KAO) warrants this product to be free of defects in material and workmanship at the time of
purchase by the original retail consumer. KAO disclaims any other warranties, express or implied, including the warranty of fitness
for a particular purpose or an intended use. If the product is found to be defective, KAO may replace or repair the product at our
option, when the product is returned prepaid, with proof of purchase. Alteration to, improper installation, or misuse of this product
voids the warranty. KAO’s liability is limited to repair or replacement of products found to be defective, and specifically excludes
liability for any incidental or consequential loss or damage.
  • Page 1 1
  • Page 2 2
  • Page 3 3
  • Page 4 4
  • Page 5 5
  • Page 6 6

TrailFX PFFG3001T Installation guide

Type
Installation guide

Ask a question and I''ll find the answer in the document

Finding information in a document is now easier with AI