TrailFX PFFF3004S fender flares are designed to add style and protection to your 2008 - 2010 Ford F-250/350 Superduty NON DUALLY. Made from durable materials, these flares are resistant to UV rays and harsh weather conditions. They are also easy to install, with no cutting or drilling required.
TrailFX PFFF3004S fender flares are designed to add style and protection to your 2008 - 2010 Ford F-250/350 Superduty NON DUALLY. Made from durable materials, these flares are resistant to UV rays and harsh weather conditions. They are also easy to install, with no cutting or drilling required.
www.TrailFX.com
Page 1 of 6 Rev 091818
NON DUALLY
REMOVE CONTENTS FROM BOX. VERIFY ALL PARTS ARE PRESENT.
READ INSTRUCTIONS CAREFULLY BEFORE STARTING INSTALLATION.
60-180 min
support@trailfx.com
1 866 638 4870
Limited Lifetime Warranty
Cutting Not
Required
PLEASE USE SAFETY GLASSES & ENSURE TO BLOCK VEHICLE
MOVEMENT DURING INSTALLATION PROCESS
IMPORTANT: DO NOT OVER-TIGHTEN THE MOUNTING SCREWS.
OVER-TIGHTENING THE SCREWS WILL RESULT IN STRESS FRACTURES.
KIT INCLUDES
Qty
Part Description
Qty
Part Description
2 ea.
Front Flares (1 Driver 1 Passenger) (A)
1 ea.
Rubber Edge Trim (26½ft ) (E)
2 ea.
Rear Flares ( 1 Driver 1 Passenger) (B)
30 ea.
Button head stainless steel bolts (F)
10 ea.
Speed clip (C)
30 ea.
Nylon Jam Nut (G)
10 ea.
Philips screws (D)
TOOLS NEEDED
13mm socket with extension
Socket Drive
7/32 socket
2mm Phillips head screw driver
4.5mm Hex key
Fender Flare
PFFF3004T / PFFF3004S
2008 - 2010: Ford F-250/350 Superduty
Drilling Not
Required
www.TrailFX.com
Page 2 of 6 Rev 091818
PRIOR TO INSTALLATION
Read these instructions before beginning the installation
Make sure kit is complete before beginning installation
Ensure you have the correct TrailFX fender flares for your vehicle before beginning the installation process.
NOTE: The flares are embossed with either a D or P indicating Passenger or Driver. Make sure you match the correct
flare to the side of the vehicle you are installing.
If you plan on painting your fender flares it must be done prior to installation. All surfaces must be cleaned and prepped
following the specifications outlined by the paint manufacturer.
PLEASE NOTE: Painted flares cannot be returned.
INSTALLING RUBBER TRIM ON NEW FENDER FLARES
Install the rubber edge trim on the outer edge of the fender flare. The outer edge is the side that comes into contact with the
vehicle’s fender. It DOES NOT get installed on the inner edge of the fender flare.
INSTALLTION OF BUTTON HEAD STAINLESS STEEL BOLTS
Step 1
Starting at one end of the flare, push the rubber trim (E)
onto the outside edge only of flare.
Step 2
Continue pressing the rubber trim (E) on to the flare in
6” increments until you reach the other end of the flare.
Repeat for the other 3 flares.
Step 1
Locate the supplied Button head stainless steel bolts (F) and nylon jam nuts (G). Install one Button head stainless steel
bolts (F) in one of the holes in the recess of the flares as shown above in the two images.
www.TrailFX.com
Page 3 of 6 Rev 091818
INSTALLING FRONT FENDER FLARES
Step 2
Proceed to the inside of the flare. Place a nylon jam nut (G) on the threads of the Button head stainless steel bolts and
tighten. Use a 13mm socket with an extension and a 4.5mm Hex key to as shown above in the two images to complete the
task.
Note: These bolts are decorative only and are not intended for securing the flares
Step 1
Locate 4 factory screws on the inner wall of the wheel
well lip. Using 7/32” socket remove screws in position #1-
3. With 2mm Philips head screw driver remove 4mm
screw, set aside 1-3mm screws for later use. Discard
4mm screws.
1
.
2
3
4
Step 2
Using step 1 image as a reference slide a supplied speed
clip (C) over the factory hole in #4 positions. NOTE: Make
sure to center speed clip hole over factory hole.
www.TrailFX.com
Page 4 of 6 Rev 091818
INSTALLING REAR FENDER FLARES
NOTE: Rear flares must be oriented correctly. Look behind the flare to find a D or P embossed on the flare. Be sure to
install the one marked with a D on the driver side of the vehicle and the one marked P on the passenger side of the
vehicle.
Step 4
Install supplied Philip screw (D) on to #4 positions,
Repeat step 1-4 to complete installation for the other side
of vehicle.
Step 3
Place front fender flare (A) on to vehicle fender.
Firmly press flare against fender and reinstall factory
screws 1-3mm using 7/32 socket.
Line up edge of
flare with edge of
fender
1
2
3
4
Step 1
Locate 4 factory screws on the inner wall of the wheel
well lip. Using 7/32” socket remove screws in position 1-
3mm . With a #2 Philips head screw driver remove 4mm
screw. Discard hardware.
1
2
3
4
Step 2
With all factory screws removed; proceed to install four
supplied speed clips (C) over factory holes. NOTE:
Make sure to center factory speed clip holes over factory
holes.
1
2
3
4
www.TrailFX.com
Page 5 of 6 Rev 091818
Step 3
Place rear fender flare (B) on to vehicle fender. Adjust
flare until holes in the flare are centered over the hole in
the speed clip. Apply firm pressure against the flare and
Install supplied Philip screw (D) onto all 4 locations.
Repeat step 1-3 to complete installation other side of the
vehicle.
1
2
3
4
www.TrailFX.com
Page 6 of 6 Rev 091818
PRODUCT CARE
1. Periodically check the product to ensure all fasteners are tight and components are intact.
2. Regular waxing is recommended to protect the finish of the product.
Check out these other TrailFX Products!! www.TrailFX.com
FAQ’s
1. Fender flares are loose after installation.
Please ensure that all required mounting brackets / hardware’s are installed & tighten correctly.
2. Missing / Excess Hardware.
Re-check hardware count as per the part list.
Keystone Automotive Operations Inc. (KAO) warrants this product to be free of defects in material and workmanship at the time of
purchase by the original retail consumer. KAO disclaims any other warranties, express or implied, including the warranty of fitness
for a particular purpose or an intended use. If the product is found to be defective, KAO may replace or repair the product at our
option, when the product is returned prepaid, with proof of purchase. Alteration to, improper installation, or misuse of this product
voids the warranty. KAO’s liability is limited to repair or replacement of products found to be defective, and specifically excludes
liability for any incidental or consequential loss or damage.
-
1
-
2
-
3
-
4
-
5
-
6
TrailFX PFFF3004S Installation guide
- Type
- Installation guide
- This manual is also suitable for
TrailFX PFFF3004S fender flares are designed to add style and protection to your 2008 - 2010 Ford F-250/350 Superduty NON DUALLY. Made from durable materials, these flares are resistant to UV rays and harsh weather conditions. They are also easy to install, with no cutting or drilling required.
Ask a question and I''ll find the answer in the document
Finding information in a document is now easier with AI
Related papers
-
TrailFX PFFC3001T Installation guide
-
-
-
-
-
-
-
-
-
Other documents
-
Rugged Ridge 11630.30 Installation guide
-
Rugged Ridge 11630.10 Installation guide
-
Rugged Ridge 11630.20 Installation guide
-
Rugged Ridge 11633.10 Installation guide
-
OMIX 11607.01 Installation guide
-
Husky INS-2805939 User manual
-
OMIX 11608.01 Installation guide
-
Bushwacker 10908-07 Installation guide
-
Rough Country 99033 Installation guide
-
Seizmik 67-10009 User manual
