QEP 22500Q User manual

Brand: QEP

Model: 22500Q

Category: Power tools

Type: User manual

READ AND FOLLOW ALL SAFETY AND

OPERATING INSTRUCTIONS BEFORE USING THIS SAW.

LIRE ET SUIVRE TOUTES LES DIRECTIVES

DE SÉCURITÉ ET D’OPÉRATION AVANT D’UTILISER CETTE SCIE.

LEA Y SIGA TODAS LAS INSTRUCCIONES

DE FUNCIONAMIENTO Y SEGURIDAD ANTES DE USAR ESTA SIERRA. TILE SAW

32CG

E200561

500

TILE WET SAW

OWNER’S MANUAL

SCIE COUPE-CARREAUX À EAU

MANUEL D'UTILISATION

SIERRA ELÉCTRICA DE

CORTE EN HÚMEDO

MANUAL DE OPERACIÓN

22500Q

7 in.

180 mm

English.......................................................................................page 1

FOR YOUR OWN SAFETY, READ INSTRUCTION MANUAL

BEFORE OPERATING SAW.

1. Always wear safety goggles when cutting.

2. Use splash hood for every operation for which it can be used.

3. Disconnect saw before cleaning or changing blade.

4. Do not use any cutting blade with openings and grooves. Use only continuous rim blades.

5. Replace damaged blade before operating.

6. Do not expose to rain or use in damp locations.

LIMITED WARRANTY — Refer to warranty card.

Français .................................................................................. page 11

POUR ASSURER VOTRE SECURITE,

LISEz LE MOIDE D'EMPLOI AVANT D'UTILISER LE COUPEUR.

1. Toujours porter des lunettes protectrices pendant la coupe.

2. Utiliser le pare-éclaboussure pour chaque opération dont il peutêtre utiliser.

3. Débrancher l'outil avant de la nettoyer ou de changer les roues.

4. Ne pas utiliser des roues à couper avec des trous ou creux. Utiliser seulement des roues à

couper lisses.

5. Remplacer les roues à couper endommagés avant de faire fonctionner l'outil.

6. Ne pas exposer à la pluie ou utiliser dans des endroits humides.

GARANTIE LIMITÉE — Faire référence à la carte de guarantie.

Español ................................................................................página 22

LEE ESTA INSTUCCION MANUAL ANTES

DE USA LA SIERRA PARA TU BIEN.

1. Siempre utilice gafas de protección al cortar.

2. Utilice una capota de protección para cada operación en la cual la puede utilizar.

3. Desconectar la sierra antes de limpiarla o antes de cambiar el disco de corte.

4. No utilice ningún disco de corte que tenga aperturas o ranuras. Solamente utilice discos de

corte lisos.

5. Reemplace el disco de corte cuando esté dañado.

6. No la exponga a la lluvia o no la utilice en áreas húmedas.

GARANTIA LIMITADA — Referirse a la tarjeta de guarantia.

Servicio al cliente de Q.E.P.: 1-866-435-8665

Q.E.P. Customer Service: 1-866-435-8665

Support de la clientèle de Q.E.P.: 1-866-435-8665

– 1 –

TABLE OF CONTENTS

General safety instructions................1

Warning ................................2

Electrical requirements . . . . . . . . . . . . . . . . . . . 3

Extension cords.......................... 4

California Proposition 65 ..................4

Description.............................. 4

Assembly ...............................5

Operation ...............................6

Maintenance . . . . . . . . . . . . . . . . . . . . . . . . . . . . 8

Troubleshooting..........................9

Parts list ................................9

Exploded parts diagram..................10

GENERAL SAFETY

INSTRUCTIONS

READ THIS OWNER'S

MANUAL COMPLETELY AND MAkE

SURE YOU UNDERSTAND ALL OF IT'S

SAFETY GUIDELINES.

1. KEEP GUARDS IN PLACE and in

working order.

2. REMOVE ADJUSTING KEYS AND

WRENCHES. Before turning on the tile saw,

make sure the keys and adjusting wrenches

have been removed.

3. KEEP WORK AREA CLEAN. Cluttered areas

and benches invite accidents.

4. ALWAYS REMAIN ALERT WHEN THE SAW

IS IN USE. Inattention on the part of the

operator may lead to serious injury.

5. DON’T USE IN A DANGEROUS

ENVIRONMENT. Don’t use power tools in

damp or wet locations or expose them to rain.

Keep work area well lit.

6. KEEP CHILDREN AWAY. All visitors should

remain at a safe distance from work area.

7. MAKE WORKSHOP CHILD-PROOF with

padlocks, master switches or by removing

starter keys.

8. USE THE RIGHT TOOL. Don’t force a tool

or attachment to do a job for which it was

not designed.

9. USE THE PROPER EXTENSION CORD. Make

sure your extension cord is in good condition.

When using an extension cord, be sure to use

one heavy enough to carry the current your

product will draw. An undersized cord will

cause a drop in line voltage resulting in loss

of power and overheating. TABLE 1 shows the

correct size to use depending on cord length

and nameplate ampere rating. If in doubt, use

the next heavier gauge. The smaller the gauge

number, the heavier the cord.

10. DON’T FORCE THE TOOL. It has been

designed to operate at maximum safety and

performance levels.

11. DO NOT FORCE THE MATERIAL BEING CUT.

Always let the blade cut at its own speed.

12. WEAR PROPER APPAREL. Do not wear

loose clothing, neckties, rings, bracelets or

other jewelry which may get caught in moving

parts. Non-slip foot wear is recommended.

Wear protective hair covering if you have

long hair.

13. ALWAYS USE SAFETY GLASSES. Also

use face or dust mask for commercial cutting

operations. Everyday eyeglasses only have

impact-resistant lenses, they are NOT

safety glasses.

14. SECURE WORK. Use clamps or a vise

instead of your hand to hold work when

practical. This safety precaution allows for

proper tool operation using both hands.

15. DON’T OVERREACH. Keep proper footing

and balance at all times.

16. MAINTAIN TOOLS WITH CARE. Keep

tools clean and in good working condition for

maximum safety performance. Follow instruc-

tions for lubricating and changing accessories.

500 TILE WET SAW

OWNER’S MANUAL

– 2 –

17. DISCONNECT TOOLS BEFORE SERVICING

– when changing accessories, such as blades,

bits, cutters, etc.

18. REDUCE THE RISK OF UNINTENTIONAL

STARTING. Make sure switch is in OFF position

before plugging in.

19. USE RECOMMENDED ACCESSORIES.

Consult the owner’s manual for recommended

accessories. The use of improper accessories

may increase risk of injury.

20. DO NOT DRY CUT WITH BLADES

DESIGNED FOR WET CUTS.

21. Make sure you USE THE CORRECT BLADE

for the job you are doing.

22. NEVER STAND ON TOOL. Serious injury

could occur if the wet saw is tipped or if the

cutting tool is unintentionally contacted.

23. CHECK DAMAGED PARTS. Before further

use of the tool, damaged part(s), (i.e., guard)

should be carefully checked to determine

that it will operate properly and perform

its intended function. Check for alignment

of moving parts, binding of moving parts,

breakage of parts, mounting and any other

condition that may affect the saw’s operation.

A guard or other part that is damaged should

be properly repaired or replaced.

24. ENSURE THAT THERE IS A CONTINUOUS

FLOW OF WATER to both sides of blade

during operation.

25. CHECK DIAMOND BLADES carefully for

cracks, nicks, missing diamond matrix or

out-of-alignment condition. Replace damaged

blades immediately. DO NOT USE DAMAGED

BLADES. They may cause bodily injury.

26. DIRECTION OF FEED. Feed work into the

blade against the direction of rotation of the

blade only.

27. DO NOT ALTER THE PLUG or use a 2-prong

receptacle. This saw is equipped with a

3-prong electrical plug.

28. NEVER LEAVE TOOL RUNNING

UNATTENDED. Turn power off. Don’t leave tool

until it comes to a complete stop.

29. POSITIONING OF TILE SAW (see FIGURE 1)

Drip

Loop

FIGURE 1

• To avoid the possibility of the appliance plug

or receptacle getting wet, position the tile

saw to one side of a wall-mounted receptacle

to prevent water from dripping onto the

receptacle or plug. The user should arrange

a “drip loop” in the cord connecting the saw

to a receptacle. The “drip loop” is that part

of the cord below the level of the receptacle,

or connector if an extension cord is used, to

prevent water traveling along the cord and

coming in contact with the receptacle.

• If the plug or receptacle does get wet, DO

NOT unplug the cord. Disconnect the fuse

or circuit breaker that supplies power to the

tool. Then, unplug and examine for presence

of water in the receptacle.

30. CHECK DIAMOND BLADES CAREFULLY

for cracks, nicks, missing diamond matrix, or

out-of alignment. Replace blades immediately.

DO NOT USE DAMAGED BLADES. They may

cause bodily injury.

WARNING

PERSONAL INJURY CAN OCCUR IF OPERATED

IMPROPERLY.

• Keep ngers and loose clothing away from

rotating blade.

• Use extreme caution when cutting tile. Make

sure hands and ngers are clear from the

blade groove in the sliding table. Severe

abrasion, cuts, or pinching of hands or

ngers can occur as the table is advanced,

particularly at the end of its travel.

• Electrical shock can occur if operating

instructions are not followed.

– 3 –

FOR YOUR OWN SAFETY READ INSTRUCTION

MANUAL BEFORE OPERATING SAW.

• Wear eye protection.

• Use splash hood for every operation for

which it can be used.

• Unplug saw before servicing, when changing

cutting wheels, and cleaning.

• Use tool only with smooth-edge cutting

wheels free of openings and grooves.

• Replace damaged cutting wheel

before operating.

• Do not ll water tray above water ll line.

ELECTRICAL

REQUIREMENTS

1. THIS TILE SAW MUST BE CONNECTED TO

A GROUNDED POWER SOURCE while in use to

protect the operator from electrical shock.

2. IN THE EVENT OF A MALFUNCTION OR

BREAKDOWN, grounding provides a path

of least resistance for electrical current to

reduce the risk of electrical shock. The tile

saw is equipped with an electrical cord with

a grounding conductor and a grounding plug.

Insert the 3-prong electrical plug into a 3-pole

receptacle that is properly installed and

grounded in accordance with all local codes

and ordinances.

3. DO NOT MODIFY THE PLUG provided if it

will not t the outlet. Have the proper outlet

installed by a qualied electrician.

4. IMPROPER CONNECTION OF THE

EQUIPMENT-GROUNDING CONDUCTOR CAN

RESULT IN A RISK OF ELECTRIC SHOCK. The

conductor with insulation that is green on the

outside (with or without yellow stripes) is the

equipment-grounding conductor. If repair or

replacement of the electrical cord or plug is

necessary, do not connect the equipment-

grounding conductor to a live terminal.

5. CHECK WITH A QUALIFIED ELECTRICIAN or

service personnel if the grounding instructions

are not completely understood, or if in doubt

as to whether the tool is properly grounded.

6. USE ONLY 3-WIRE EXTENSION CORDS that

have 3-prong grounding plugs and 3-pole

receptacles that accept the tile saw’s plug.

7. REPAIR OR REPLACE DAMAGED OR WORN

CORD IMMEDIATELY.

8. IF THE PLUG OR RECEPTACLE DOES GET

WET, DO NOT UNPLUG THE CORD. Disconnect

the fuse or circuit breaker that supplies power

to the tool. Then, unplug and examine for

presence of water in the receptacle.

9. ONLY UL-LISTED EXTENSION CORDS

SHOULD BE USED WITH THIS PRODUCT.

10. IMPROPER USE OF EXTENSION CORDS

MAY CAUSE INEFFICIENT OPERATION OF

YOUR TOOL, which can result in overheating.

Be sure your extension cord is rated to allow

sufcient current ow to the motor. For the

proper gauge for this tile saw, please refer

to TABLE 1.

11. DO NOT LET YOUR FINGERS TOUCH

THE TERMINALS of plug when installing or

removing the plug to or from the outlet.

12. THIS TILE SAW MUST BE PROPERLY

GROUNDED. The risk of electric shock and

bodily injury are greatly increased if it is not,

particularly when used in damp locations or in

proximity to plumbing.

NOTE: This tool is intended for use on a

circuit that has an outlet that looks like the

one illustrated in FIGURE 2 (A). The tool has

a grounding plug that looks like the plug

illustrated in FIGURE 2 (A). A temporary

adapter, which looks like the adapter

illustrated in FIGURE 2 (B) and (C), may be used

to connect this plug to a 2-pole receptacle

as shown in FIGURE 2 (B) if a properly

grounded outlet can be installed by a qualied

electrician. The green-colored rigid prongs

extending from the adapter must be connected

to a permanent ground such as a properly

grounded outlet box.

(not permitted in Canada)

(A) Grounding

Metal

screw

(B) Grounding outlet box

FIGURE 2

– 4 –

EXTENSION CORDS

1. Use only extension cords that are intended

for outdoor use. These extension cords are

identied by a marking “Acceptable for use

with outdoor appliances: store indoors while

not in use.” Use only extension cords having

an electrical rating not less than the rating of

the product. Do not use damaged extension

cords. Examine extension cord before using

and replace if damaged. Do not abuse

extension cords and do not yank on any cord

to disconnect. Keep cord away from heat and

sharp edges. Always disconnect the extension

cord from the receptacle before disconnecting

the product from the extension cord.

TO REDUCE THE RISk

OF ELECTROCUTION, kEEP ALL CONNECTIONS

DRY AND OFF THE GROUND. DO NOT TOUCH

PLUG WITH WET HANDS.

2. Ground Fault circuit Interrupter (GFCI)

protection should be provided on the circuit(s)

or outlet(s) to be used for the tile saw.

Receptacles are available having built-in GFCI

protection and may be used for this measure

of safety.

3. USE PROPER EXTENSION CORD. Make

sure your extension cord is in good condition.

When using an extension cord, be sure to use

a cord heavy enough to carry the current your

product will draw. An undersized cord will

cause a drop in line voltage, resulting in loss

power and overheating. TABLE 1 shows the

correct size to use depending on cord length

and nameplate ampere rating. If in doubt, use

the next heavier gauge. The smaller the gauge

number, the heavier the cord.

NOTE: When using an extension cord, ensure

all cords are no smaller than #12 gauge, rated

at a 20-amp minimum, and equipped with

3-prong plugs. Use of anything smaller may

result in overheating or burn out of the motor. It

is recommended to have an electrician check

the voltage at the saw motor to ensure proper

voltage to run the saw efciently and safely.

CALIFORNIA

PROPOSITION 65

SOME DUST CREATED

BY POWER SANDING, SAWING, GRINDING,

DRILLING AND OTHER CONSTRUCTION

ACTIVITIES CONTAIN CHEMICALS kNOWN

TO THE STATE OF CALIFORNIA TO CAUSE

CANCER, BIRTH DEFECTS OR OTHER

REPRODUCTIVE HARM.

Some examples of these chemicals are:

• Lead from lead-based paints

• Crystalline silica from bricks and cement and

other masonry products

• Arsenic and chromium from chemically-

treated lumber

Your risk from these exposures varies,

depending on how often you do this type

of work. To reduce your exposure to these

chemicals: work in well ventilated area, and

work with approved safety equipment, such

as those dust masks that are specically

designed to lter out microscopic particles.

DESCRIPTION

Before attempting to use any tool, be sure

to familiarize yourself with all the operating

features and safety instructions.

KNOW YOUR SAW

Your tile saw has many built-in features (see

FIGURE 3) for fast, efcient cutting of ceramic,

marble, slate or limestone wall or oor tile.

Ampere rating

Volts Total length of cord in feet

120 V 25 ft. 50 ft. 100 ft. 150 ft.

240 V 50 ft. 100 ft. 200 ft. 300 ft.

More than No more than AWG

0 6 18 16 16 14

6 10 18 16 14 12

10 12 16 16 14 12

12 16 14 12 Not recommended

TABLE 1

– 5 –

The durable 7 inch blade cuts tile up to 1 1/4

in (33 mm) thick. The adjustable rip and angle

guides allow 90° rip cuts and 0° to 45° miter

cuts on both the right and left sides. The left

cutting table is hinged so it can be adjusted

for 15°, 30° and 45° miter cuts. The right table

has a built-in water reservoir for cooling the

blade. The water reservoir has a side overow

hole for proper water level. The built-in handle

allows easy transporting. The convenient

storage area on bottom holds accessories.

PRODUCT SPECIFICATIONS

Input: 4.8 Amps

No-load Speed: 3600 RPM

Output: 3⁄4-Peak HP

Blade Diameter: 7 in (180 mm)

Rating: 120 Volts~60 Hz AC

Depth of Cut: 1 1⁄4 in (33 mm)

ASSEMBLY

FOLLOW ALL OF THE

ASSEMBLY AND OPERATION INSTRUCTIONS

COMPLETELY BEFORE CONNECTING THE

SAW TO A POWER SOURCE OR TURNING THE

MOTOR ON.

UNPACKING

1. Remove all packing materials from around

your saw.

2. Carefully lift the saw from carton and place

it on a level work surface.

3. Do not discard the packing materials until

you have carefully inspected the saw for loose

or damaged parts.

The following items are included in box with

your tile saw: 7 in Diamond Blade, Blade

Guard, Rip Guide, Angle Gauge, Universal

Wrench and Owner’s Manual

4. Inspect the saw carefully to make sure that

no breakage or damage has occurred during

shipping. If any parts are damaged or missing

return the saw to your place of purchase.

IF ANY PARTS ARE

DAMAGED OR MISSING, DO NOT ATTEMPT

TO OPERATE THIS SAW. OPERATING THIS

SAW WITH DAMAGED OR MISSING PARTS

Rip Guide

Left Cutting

Table Hinge Blade Guard

Right Cutting

Table

Bottom

Storage Area

On/Off

Switch

Water

Reservoir

Angle Guide

FIGURE 3

– 6 –

COULD RESULT IN POSSIBLE SERIOUS

PERSONAL INJURY.

INSTALLING THE BLADE

(see FIGURE 4)

1. Carefully place the blade onto the shaft and

push it against the inner ange.

2. Be sure the side of the blade with the

directional arrow is facing towards you.

3. Place the outer ange and the blade shaft

nut onto blade.

4. Firmly tighten the blade shaft nut with the

included wrench, but do not over tighten.

USE ONLY

CONTINUOUS RIM BLADES WITH THIS SAW.

DO NOT USE SEGMENTED, “TURBO” BLADES,

WOOD SAWING BLADES, BLADES WITH

OPENINGS, OR ANY OTHER CUTTING DEVICES

WITH THIS TILE SAW. USING THESE BLADES

COULD RESULT IN SERIOUS PERSONAL

INJURY AND DAMAGE TO THE SAW.

FIGURE 4

INSTALLING THE BLADE GUARD

(see FIGURE 5)

1. Place the guard support into the socket.

2. Be sure the support is parallel to the blade.

3. Place blade guard onto the support and

tighten wing nut.

FIGURE 5

INSTALLING THE RIP GUIDE

(see FIGURE 6)

1. Place rip guide on the top of the cutting

table and clamp both ends.

NOTE: The rip guide can be placed on either

the left or right side.

FIGURE 6

INSTALLING THE ANGLE GUIDE

(see FIGURE 7)

1. The angle guide is designed to t on top

of the rip guide. Simply place notch in angle

guide onto the top of the rip guide.

NOTE: The angle guide can be placed on either

the left or right side.

FIGURE 7

OPERATION

IMPORTANT: ALWAYS turn off the saw and

remove the plug from the outlet BEFORE

adding or removing accessories and making

adjustments.

FAILURE TO UNPLUG

THE SAW COULD RESULT IN ACCIDENTAL

STARTING CAUSING POSSIBLE SERIOUS

PERSONAL INJURY.

– 7 –

BEFORE STARTING THE SAW

(see FIGURE 8)

1. Remove the blade guard.

2. Open the right cutting table and ll the water

reservoir to the recommended level. DO NOT

ll above the lines.

NOTE: ALWAYS keep enough water in the

reservoir when operating the saw. DO NOT let

the saw run dry.

3. Re-attach the blade guard and close the

right cutting table.

IMPORTANT: ALWAYS completely drain the

water reservoir after each use.

FIGURE 8

TO START THE SAW

(see Figure 9)

1. Remove cord from compartment under the

saw and connect it to a GFCI (Ground Fault

Circuit Interrupter) protected outlet.

2.Push On/Off switch to the “On” position.

FIGURE 9

MAKING CUTS

The edge of the cutting table has easy-to-see

dimensions (in both inches and centimeters)

for cutting accuracy.

IMPORTANT: ALWAYS let the blade cut at its

own speed. DO NOT force the material being

cut. ALWAYS check the blade for cracks or

damage BEFORE each use.

MAKING 90° RIP CUTS

(see FIGURE 10)

1. Install the rip guide by placing it at the

desired position according to the width of the

cut you are making.

2. Place the material to be cut against the

tile guide.

3. Carefully feed the material into the blade.

FIGURE 10

MAKING 0°– 45° ANGLE CUTS

(see FIGURE 11)

1. Install the angle guide on the top of the

rip guide.

2. Select desired angle and tighten the

adjustment knob.

3. Carefully push the angle guide and material

towards the blade.

FIGURE 11

MAKING MITER CUTS

(see FIGURE 12)

– 8 –

1. Raise the left cutting table to the desired

angle. NOTE: Choose 15°, 30° or 45° angles.

2. Place the 2 braces into the grooves to hold

the cutting table in place.

3. Place the material to be cut onto left cutting

table.

4. Carefully push the material towards the

blade.

FIGURE 12

MAINTENANCE

TO AVOID ACCIDENTS,

ALWAYS DISCONNECT THE TOOL FROM

THE POWER SOURCE BEFORE CLEANING OR

PERFORMING ANY MAINTENANCE

Please do not try to service this machine on

your own.

Avoid using solvents when cleaning plastic

parts. Most plastics are susceptible to damage

from various types of commercial solvents

and may be damaged by their use. Use clean

cloths to remove dirt, carbon dust, etc.

DO NOT AT ANY TIME

LET BRAkE FLUIDS, GASOLINE, PETROLEUM-

BASED PRODUCTS, PENETRATING OILS, ETC.

COME IN CONTACT WITH PLASTIC PARTS.

THEY CONTAIN CHEMICALS THAT CAN

DAMAGE, WEAkEN OR DESTROY PLASTIC.

1. ALWAYS clean the tile saw after each use

and store it in a dry location.

2. ALWAYS wipe off all exterior surfaces

and keep the cutting table clean and free of

all debris.

3. ALWAYS check the blade for cracks or

damage BEFORE each use.

4. ALWAYS store the cord in the compartment

underneath the saw after each use.

DIAMOND BLADES

• Use only 7 in. (180 mm) continuous rim

diamond blades in this saw.

• This tile saw is to be used with only

continuous rim diamond blades. Failure to

do so may result in severe bodily injury and

damage to the saw.

• This saw comes with a standard blade that is

ideal for cutting ceramic tile. If your project

requires the cutting of other substrates (ex.

porcelain, slate, stone), it is recommended

that you use the specic type of blade for the

material being cut.

DIAMOND BLADE DO’S & DON’TS

1. DO inspect blades daily for cracks or uneven

wear. Discard cracked, chipped or bent

blades!

2. DO use manufacturer’s recommendation for

matching the right blade with the right material

being cut.

3. DO inspect the arbor shaft for uneven wear

before mounting the blade.

4. DO use blades with the correct arbor size on

a compatible arbor shaft.

5. DO ensure the blade is mounted with the

rotation arrow in the proper direction and is

securely tightened with a wrench.

6. DO wear proper safety equipment at

all times when operating the saw. Wear

goggles and dust mask at all times when

operating saw.

7. DO periodically check the blade for cracks

or bond fatigue.

8. DO ensure a continuous ow of water

on both sides of the blade before cutting

any material.

1. DO NOT operate the saw without all safety

guards in position.

2. DO NOT operate the saw with blades larger

or smaller than recommended.

3. DO NOT cut dry with blades marked

“Use Wet.”

4. DO NOT exceed maximum RPMs

recommended by the blade manufacturer.

– 9 –

5. DO NOT force the material into the blade. Let

the blade cut at its own speed.

6. DO NOT cut material not recommended by

the blade manufacturer.

TROUBLESHOOTING

OVERHEATING OF SAW:

1. Turn saw off and let it rest until motor is cool

to the touch.

2. Check and clean the ventilation slots,

removing blockage and dirt.

THE SAW DOES NOT START:

1. Check that power cord is properly

plugged in.

2. No power from outlet.

3. Switch is damaged.

PARTS LIST

See exploded parts diagram on page 10.

PART # DESCRIPTION

22500-1 Blade Guard Set (w/ Screw,

Wing Nut, Washer & Guard

Support)

22500-2 Miter Guide Set (w/

Adjustment Knob & Hex Nut)

22500-3 Rip Guide

22500-4 Left Cutting Table

22500-5 Right Cutting Table

22500-6 Upper Frame

22500-7 Blade Lock Nut

22500-8 Outer Flange

6-7003Q (9) 7 in Continuous Rim Blade

22500-10 Inner Flange

22500-11 Oil Seal for Motor

22500-12 Motor (w/5 Screws)

22500-13 Capacitor (w/Screw)

22500-14 Main Frame (w/6 Screws)

22500-15 Waterproof Switch (w/

Waterproof Rubber Cover)

22500-16 Carrying Handle

22500-17 Rubber Base (4)

22500-18 Power Cord

22500-19 Strain Relief Bushing

22500-20 Power Cord Shelter

22500-21 Universal Wrench

Page is loading ...

Made in Taiwan

Fabriqué en Taiwan

Hecho en Taiwan

Boca Raton, FL 33487

www.qep.com

T1214-9125

QEP 22500Q User manual

Brand: QEP

Model: 22500Q

Category: Power tools

Type: User manual

Download PDF

report

in other languages

français: QEP 22500Q Manuel utilisateur
español: QEP 22500Q Manual de usuario

QEP 22500Q User manual

QEP 22500Q User manual

in other languages

Related papers

Other documents