none X-RC7098 Installation guide

Brand: none

Model: X-RC7098

Category: Hardware cooling accessories

Type: Installation guide

None X-RC7098

The None X-RC7098 is a wireless remote controller for ceiling fans that allows you to conveniently operate your fan from anywhere in the room. It features 16 frequency modes, so you can choose the best channel to avoid interference from other remote-controlled devices. The remote control can be used to turn the fan on or off, adjust the fan speed, and set the fan to oscillate. It also has a built-in timer that allows you to set the fan to turn off automatically after a certain amount of time.

The None X-RC7098 is easy to install and use. Simply follow the instructions in the included manual to connect the receiver to your fan and the transmitter to the remote control. Once the remote control is paired with the receiver, you can start using it to control your fan.

None X-RC7098

The None X-RC7098 is a wireless remote controller for ceiling fans that allows you to conveniently operate your fan from anywhere in the room. It features 16 frequency modes, so you can choose the best channel to avoid interference from other remote-controlled devices. The remote control can be used to turn the fan on or off, adjust the fan speed, and set the fan to oscillate. It also has a built-in timer that allows you to set the fan to turn off automatically after a certain amount of time.

The None X-RC7098 is easy to install and use. Simply follow the instructions in the included manual to connect the receiver to your fan and the transmitter to the remote control. Once the remote control is paired with the receiver, you can start using it to control your fan.

REMOTE CONTROLLER WIRING CHART

Step 1: To Set Frequency before making wire connection.

*

There is a Frequency Setter respectively in Transmitter

& Receiver (as figure 1). When produced, all of 4 keys

on the frequency setters are in "ON" position. Basically,

customers do not need to adjust the frequency and

the remote control.

*

If you buy one more remote controlled fan or the

frequency is interrupted, the fan may function abnormally.

In this situation, you need to change the fan frequency.

There are 16 modes of setting frequency for you to

select the best channel to operate the fan (see figure 2).

Following are the 16 modes for your channel selection.

Please use a pin to switch the keys carefully.

*

White Wire from Outlet Box to Red Wire from

Receiver with "AC IN N" sticker.

*

Black Wire from Outlet Box to Red Wire from

Receiver with "AC IN L" sticker.

*

Black Wire from Receiver to Black Wire from Motor.

*

Blue Wire from Receiver to Blue Wire from Motor.

White Wire from Receiver to White Wire from Motor.

*

Brown Wire from Receiver to Brown Wire from Motor.

*

Ground Wire from Outlet Box to Green Ground Wire

from Motor bracket & Down Rod.

*

Install the battery (not included) to transmitter.

Turn on the electric power. Press button to operate the fan.

Warning:

Before installing Remote Controller,

make sure the Main Power Supply is turned off.

AC : 110-130V/60HZ

LIGHT : 165W ( MAX )

FAN : 85W ( MAX )

Neutral Wire From

Outlet Box

(

White Wire

)

Receiver

Fan

Red Wire

with

"AC IN L" sticker

Red Wire

with

"AC IN N" sticker

Hot Wire From

Outlet Box

(Black Wire)

Ground Wire

(Green Wire)

*** Please note to change the frequency-setters in the transmitter

& receiver at the same time & in the same key position.***

When 1 key is in "OFF" position.

When 2 keys are in "OFF" position.

When 3 keys are in "OFF" position.

When 4 keys are in "ON" or "OFF" position.

1.)

2.)

3.)

4.)

ON DIPON DIP

11

22 33

44

KeyKey

" ON" position

" OFF" position

( Fig 1.)( Fig 1.)

1

2 3

4

1

2 3

4

1

2 3

4

1

2 3

4

1

2 3

4

1

2 3

4

1

2 3

4

1

2 3

4

1

2 3

4

1

2 3

4

1

2 3

4

1

2 3

4

1

2 3

41

2 3

4

1

2 3

4

1

2 3

4

( Fig 2.)( Fig 2.)

Step 2: To make wire connection.

Antenna

X-RC7098

1

none X-RC7098 Installation guide

Brand: none

Model: X-RC7098

Category: Hardware cooling accessories

Type: Installation guide

None X-RC7098

The None X-RC7098 is a wireless remote controller for ceiling fans that allows you to conveniently operate your fan from anywhere in the room. It features 16 frequency modes, so you can choose the best channel to avoid interference from other remote-controlled devices. The remote control can be used to turn the fan on or off, adjust the fan speed, and set the fan to oscillate. It also has a built-in timer that allows you to set the fan to turn off automatically after a certain amount of time.

The None X-RC7098 is easy to install and use. Simply follow the instructions in the included manual to connect the receiver to your fan and the transmitter to the remote control. Once the remote control is paired with the receiver, you can start using it to control your fan.

Related papers

none X-RC6776 Installation guide

Other documents