none X-RC6776 Installation guide

Category
Household fans
Type
Installation guide

none X-RC6776

none X-RC6776 is a remote controller for ceiling fans and light kits. It allows you to control the fan speed (high, medium, low, off) and the light (on/off), and it has a memory function so that the fan and light will operate at the same speed and status as the last time the power supply was turned off.

Here are some of the key features and possible use cases for the none X-RC6776:

  • Convenience: The remote control allows you to operate the fan and light from anywhere in the room, without having to get up and pull on a chain or switch. This is especially convenient if the fan is high up on the ceiling or if you have mobility issues.

none X-RC6776

none X-RC6776 is a remote controller for ceiling fans and light kits. It allows you to control the fan speed (high, medium, low, off) and the light (on/off), and it has a memory function so that the fan and light will operate at the same speed and status as the last time the power supply was turned off.

Here are some of the key features and possible use cases for the none X-RC6776:

  • Convenience: The remote control allows you to operate the fan and light from anywhere in the room, without having to get up and pull on a chain or switch. This is especially convenient if the fan is high up on the ceiling or if you have mobility issues.
1.) You must set ceiling fan manual switch to high speed and light kit (if any) to on position before
operating remote control.
2.) Read and save these instructions.
3.) Please note that all-fixed wiring appliances should be installed by a qualified electrician.
4.) The supply to the remote control receiver should be connected through a mains switch, i.e. existing
wall switch.
5.) Before installing Remote Controller, make sure the Main Power Supply is turned off.
6.) Install receiver into the ceiling fan canopy of the fan to ensure proper protection.
7.) Electric Rating: AC120V, Light: 300W (Max), Fan: 1.25A (Max).
8.) Do not install in damp locations or immerse into water. (For indoor use only.)
9.) Do not install in Tungsten Light kit, only for the Energy saving bulb.
10.) Do not pull on or cut leads shorter.
11.) Do not drop or bump the unit.
12.) The Battery will weaken with age and should be replaced before leaking takes place as this will
damage the transmitter. Dispose of used battery properly. Keep the battery out of reach of children.
13.) CAUTION: To reduce the risk of fire or injury, do not use this product in conjunction with any
variable(rheostat) wall control.
REMOTE CONTROLLER INSTALLATION INSTRUCTION
IMPORTANT NOTE:
There is a code switch in transmitter and
receiver (See Fig.1). First. Set all of the 4
keys at "ON" position. If more than one
remote controlled fan is installed or the code
interfered, the fan may function abnormally.
In this situation, you need to reset the fan code
switch as per following instructions.
Please use a ball pen (or any convenient tool) to
poke keys to select a desired code mode which
will not interfere with other electrical units. There
are 15 code modes for selection excluding the
original ex-factory mode. (See Fig.2)
SET CODE SWITCH BETWEEN TRANSMITTER AND RECEIVER:
1
2 3
4
1
2 3
4
1
2 3
4
1
2 3
4
1
2 3
4
1
2 3
4
1
2 3
4
1
2 3
4
1
2 3
4
1
2 3
4
1
2 3
41
2 3
4
1
2 3
4
1
2 3
4
1
2 3
4
1
2 3
4
( Fig 2.)( Fig 2.)
*** Please note to change the code switches in the
transmitter & receiver at the same time & at the
same key position.***
When 1 key is in "OFF" position.
When 2 keys are in "OFF" position.
When 3 keys are in "OFF" position.
When 4 keys are in "ON" or "OFF" position.
Page 1
ON DIPON DIP
11
22 33
44
KeyKey
"ON" position
"OFF" position
( Fig 1.)( Fig 1.)
CODE SWITCH
(Ex-Factory Mode)
TO INSTALL THE BATTERY, PRESS DOWN AND
SLIDE OUT BATTERY HOUSING COVER.
Battery Housing
Cover
1.) Make sure the electric power was turned off.
2.) Ceiling fan must be set at HIGH speed and light kit (if any) at
ON position by pulling the "Pull Switch" after installation.
3.) Once the connection has been made, the receiver inserts into
the drop rod hanging bracket. The canopy comes up to cover
the receiver and bracket. (See Fig.3)
4.) Make Wire Connection: (See Fig.4)
a. The Motor white wire to the white "To Motor N" wire from Receiver with a wire nut.
b. The Motor black wire to the black "To Motor L" wire from Receiver with a wire nut.
c. The Motor blue wire to the blue "For Light" wire from Receiver with a wire nut.
d. The white wire from Outlet Box to the red "AC in N" wire from Receiver with a wire nut.
e. The black wire from Outlet Box to the red "AC in L" wire from Receiver with a wire nut.
Make sure all of wire nuts are connected firmly.
Tuck all wire nuts and wires carefully up into the Outlet Box, EXCEPT antenna, which should
remain outside Outlet Box.
INSTALL AND MAKE WIRE CONNECTION:
TRANSMITTER
Fig.6
Fig.5
Fig.3
Fig.4
FAN/OFF
LIGHT
ON/OFF
HI
LOW
MED
5.) Install a 9V battery (not included) into the transmitter. Turn on the power, press button of
transmitter to operate the fan. (See Fig.5)
6.) Functions of Transmitter. (See Fig.6)
Hanger Ball
Receiver
a.
b.
c.
d.e.
Antenna:
Antenna
(Leave unconnected
and do not cut)
VIEW AFTER INSTALLATION
DO NOT CUT
OR SPLICE
Battery 9V
HI: Turn on the fan at high speed.
MED: Turn on the fan at medium speed.
LOW: Turn on the fan at low speed.
FAN/OFF: Turn off the fan.
LIGHT ON/OFF:
Press and release immediately to turn on or off the light.
Page 2
Wall Bracket
Transmitter
7.) Install the transmitter wall bracket in wall by two screws and hang transmitter in it carefully.
(See Fig.7)
Screw
Note:
This remote controller has memory function
setting. The fan will operate at the same
speed and the fan light will stay at the same
status as the last time the power supply was
turned off.
Fig.7
FAN/OFF
LIGHT
ON/OFF
HI
MED
LOW
Hanger Bracket
  • Page 1 1
  • Page 2 2

none X-RC6776 Installation guide

Category
Household fans
Type
Installation guide

none X-RC6776

none X-RC6776 is a remote controller for ceiling fans and light kits. It allows you to control the fan speed (high, medium, low, off) and the light (on/off), and it has a memory function so that the fan and light will operate at the same speed and status as the last time the power supply was turned off.

Here are some of the key features and possible use cases for the none X-RC6776:

  • Convenience: The remote control allows you to operate the fan and light from anywhere in the room, without having to get up and pull on a chain or switch. This is especially convenient if the fan is high up on the ceiling or if you have mobility issues.

Ask a question and I''ll find the answer in the document

Finding information in a document is now easier with AI