Klimaire KTIR24H2 User manual

Brand: Klimaire

Model: KTIR24H2

Category: Split-system air conditioners

Type: User manual

This manual is also suitable for

AIR CONDITIONER

REMOTE CONTROLLER

Thank you very much for purchasing our air conditioner.

Please read this owner's manual carefully before using

your air conditioner.

MODE

FAN SPEED

AUTO

COOL

DRY

HEAT

FAN

ILLUSTRATION

Model

Lowest Voltage of

CPU Emitting Signal

Rated Voltage

3.0V(Dry batteries R03/LR03 2)

2.4V

Remot e Con trolle r Spe cificat ions

1. Operating Mode: AUTO, COOL, DRY, HEAT(cooling & heating models only),

and FAN.

2. Timer Setting Function in 24 hours.

O O O O

3. Indoor Setting Temperature Range : 6 2 F~86 F(17 C~30 C).

4. Full function of LCD (Liquid Crystal Display).

Environment

Signal Receiving

Range

Perfor manc e Featur e

MODE

FAN SPEED

AUTO

COOL

DRY

HEAT

FAN

Sliding door

(closed)

RG05F2/BGEU1

O O O O

23 F~140 F(-5 C~60 C)

Funct ion bu ttons

Each time the button is pressed, the operation

mode is selected in a sequence of following:

MODE Button

ON/OFF Button

Operation starts when this button is pressed

and stops when this button is pressed again.

NOTE: Please do not select HEAT mode if the

machine you purchased is cooling only type. Heat

mode is not supported by the cooling only

appliance.

AUTO

COOL

DRY

HEAT FAN

SLEEP Button

NOTE: While the unit is running under SLEEP

mode, it would be cancelled if MODE, FAN

SPEED or ON/OFF button is pressed.

Active/Disable sleep function. It can maintain

the most comfortable temperature and save

energy. This function is available on COOL,

HEAT or AUTO mode only .

SWING V Button

Used to stop or start horizontal louver move-

ment and set the desired up/down air flow

direction. Push once, the louver changes 6

degree in angle. Keep pushing more than 2

seconds, the louver will swing up and down

automatically.

MODE

FAN SPEED

SWING V SLEEP

TIMER ON

TIMER OFF

CLOCK

RESET LOCK

AUTO

COOL

DRY

HEAT

FAN

TURBO

LED

Sliding door

(opened)

SWING H

SWING H Button

Used to stop or start vertical louver movement

and set the desired left/right air flow direction.

The vertical louver changes 6 degree in angle

for each press.If keep pushing more than 2

seconds,the vertical louver swing feature is

activated.(Not applicable to all the units,please

refer to the OWNER S MANUAL for details).

SELF CLEAN

I FEEL

I FEEL /SELF CLEAN Fun ction

Press this button less than 2 seconds will

initiate I FEEL function. And if keep pressing

this button more than 2 seconds, the

SELF CLEAN function is initiated.

Funct ion bu ttons (cont inued )

Used to select the fan speed in four steps:

AUTO LOW MED HIGH

FAN SPEED Button

DOWN Button

Push this button to decrease setting temperature

or to decrease Hour during Clock time setting.

NOTE: Press and hold UP and DOWN buttons

together for 3 seconds will alternate the temper-

O O

ature display between the C & F scale.

UP Button

Push this button to increase setting temperature

or to increase Hour during Clock time setting.

LOCK Button

Press this recessed button to lock all current

settings, and the remote controller will not

accept any operation except that of the LOCK.

Use the LOCK mode when you want to prevent

settings from being changed accidentally.

Press the LOCK button again to cancel the

LOCK function. A lock symbol will appear on

the remote controller display when the lock

function is activated.

RESET Button

Once the recessed RESET button is pressed,

all of the current settings will be cancelled

and the controller will return to the initial settings.

MODE

FAN SPEED

SWING V SLEEP

TIMER ON

TIMER OFF

CLOCK

RESET LOCK

AUTO

COOL

DRY

HEAT

FAN

TURBO

LED

SWING H

SELF CLEAN

I FEEL

When the I FEEL function is activated, the

remote display is actual temperature at its

location. The remote control will send this

signal to the air conditioner every 3 minutes

interval until press the I FEEL button again.

This indicator light remains on.

The I FEEL function is not available under

DRY and FAN mode.

Switch the operation mode or turn off the unit

will cancel the I FEEL function automatically.

Under SELF CLEAN mode, the air conditioner

will automatically clean and dry the Evaporator

and keep it as fresh for the next operation.

TURBO

Active/Disable Turbo function. Turbo function

enables the unit to reach the preset temperature

in the shortest time. When press this button

on heating mode(applicable to the unit adopts

PTC only), the PTC will be energized and bring

fast heating operation.

LED Button

Disable/Active indoor screen Display.

TIMER ON Button

Press this button to activate the Auto-on time

setting. Each press will increase the time setting

in 30 minutes increments, up to 10 hours, then at

1 hour increments up to 24 hours. To cancel the

Auto-on time setting, just press the button until

the time setting is 0.0.

TIMER OFF Button

Press this button to activate the Auto-off time

setting. Each press will increase the time setting

in 30 minutes increments, up to 10 hours, then at

1 hour increments up to 24 hours. To cancel the

Auto-off time setting, just press the button until

the time setting is 0.0.

CLOCK Button

Used to set the remote clock.

NOTE:

Buttons design might be slightly different

from the actual one depending on individual

models.

All the functions described above are

accomplished by the indoor unit, if the

indoor unit has no this feature, there is no

corresponding operation happened when

press the relative button on the remote

controller.

Please do not select HEAT mode if the

machine you purchased is cooling only

type. Heat mode is not supported by the

coolingonly appliance.

MODE

FAN SPEED

SWING V SLEEP

TIMER ON

TIMER OFF

CLOCK

RESET LOCK

AUTO

COOL

DRY

HEAT

FAN

TURBO

LED

SWING H

SELF CLEAN

I FEEL

Indica tors on LC D

Transmission Indicator

Temp. display

Time display

Fan speed display

Sleep Display

Mode display

ON/OFF display

This transmission indicator lights when remote

controller transmits signals to the indoor unit.

Displays the current operation mode. Including

AUTO( ), COOL( ), DRY( ), HEAT( )

(Not applicable to cooling only models), FAN( )

and back to AUTO( ).

O O O

Displays the temperature setting(62F ~86F /17C ~

30C ). When you set the operating mode to FAN, no

temperature setting is displayed.

Displayed by pressing the ON/OFF button.

Press the ON/OFF button again to remove.

Indicate Timer on/off time(0~24 hours) or clock

time. The clock time is indicated only when no AUTO-

ON/OFF timer is set. When AUTO-TIMER feature is

operating, it displays the AUTO-ON/OFF time. To

check the current time, press the CLOCK button, and

the time will display.

Displays the selected fan speed, AUTO( ) and three

fan speed levels " " (LOW) " " (MED)

" " (HIGH) can be indicated. The fan speed

is auto controlled under AUTO or DRY mode.

Displayed under sleeping operation.

Press the SLEEP button again to remove.

AUTO

Lock Display

Displayed when LOCK mode is activated.

AUTO

COOL

DRY

HEAT

FAN

TEMP.

SET

CLOCK

TIMER

HOUR

ON OFF

Note:

All displays on the remote controller are

shown for illustration purposes only.

I FEEL Display

Displayed when I FEEL function is activated.

Static electricity or other factors (Voltage transients) can

cause the remote controller clock to initialize. If your

remote controller is initialized (the time of "12:00"

flashing), readjust the clock before starting the unit.

CAUTION

How to use t he bu ttons

Before you start operating the air conditioner, set

the clock of the remote controller using the proce-

dures given in this section. The clock panel on the

remote controller will display the time regardless of

whether the air conditioner is in use or not.

After batteries are inserted in the remote controller,

the clock panel will display "12:00" and begin to flash.

1. UP/DOWN button

Press these buttons to set time.

Forward.

Backward.

Each time you press the button, the time moves

forward or backward by one minute depending

on which side you press. The time alters as quickly

as you push the button.

Keep pressing the button without releasing, the

time moves forward or backward by 10 minutes

depending on which side you press.

Initial Setting the Clock

When the right time is achieved, press the CLOCK

button or release the or and wait for 5

seconds, the clock time stops flashing and the

clock starts operating.

Press the CLOCK button on the remote controller,

the time of the clock display will start to flash. To

set the new time, follow 1 and 2 of "Initial Setting

of the Clock".

Note: The time of the CLOCK must be set before

the AUTO-TIMER feature will operate.

* Clock accuracy is within 15 seconds per day.

3.Readjusting the Clock

CLOCK button

MODE

FAN SPEED

SWING V SLEEP

TIMER ON

TIMER OFF

CLOCK

RESET LOCK

AUTO

COOL

DRY

HEAT

FAN

TEMP.

SET

CLOCK

TIMER

HOU R

ON OFF

SWING H

SELF CLEAN

TURBO

LED

I FEEL

Coolin g /Hea ting/Fa n ope ration

Ensure the unit is plugged in and power is

available.

1. Press the MODE button to select COOL, HEAT,

(cooling & heating models only) or FAN mode.

2. Press the UP/DOWN buttons to set the

desired temperature.

3. Press the FAN SPEEDbutton to select the

fan speed in four steps- Auto, Low, Med,or

High.

4. Press the ON/OFF button to start the air

conditioner.

The temperature can

O O O

be set within a range of 62F~86 F in 1F

increments.

In the FAN mode, the setting temperature is not

displayed in the remote controller and you are not able

to control the room temperature either. In this case,

only step 1, 3 and 4 may be performed.

NOTE

Auto o perat ion

Ensure the unit is plugged in and power is

available. The OPERATION indicator on the

display panel of the indoor unit starts flashing.

1. Press the MODE button to select Auto.

2. Press the UP/DOWN button to set the

desired temperature. The temperature can

O O O

be set within a range of 62F~86 F in 1F

increments.

3. Press the ON/OFFbutton to start the air

conditioner.

1. In the Auto mode, the air conditioner can logically

choose the mode of Cooling, Fan, and Heating

by sensing the difference between the actual

ambient room temperature and the setting

temperature on the remote controller.

2. In the Auto mode, you can not switch the fan speed.

It has already been automatically controlled.

3. If the Auto mode is not comfortable for you , the

desired mode can be selected manually.

NOTE

MODE

FAN SPEED

AUTO

COOL

DRY

HEAT

FAN

TEMP.

SET

CLOCK

HOUR

AUTO

COOL

DRY

HEAT

FAN

TEMP.

SET

CLOCK

HOU R

MODE

FAN SPEED

1010

Dehum idifyin g ope ration

Ensure the unit is plugged in and power is

available. The OPERATION indicator on the

display panel of the indoor unit starts flashing.

1. Press the MODE button to select DRY mode.

2. Press the UP/DOWN buttons to set the

desired temperature.

3. Press the ON/OFF button to start the air

conditioner.

The temperature can

O O O

be set within a range of 62F~86 F in 1F

increments.

In the Dehumidifying mode, you can not switch the

fan speed. It has already been automatically controlled.

NOTE

Adjus ting a ir flow dire ction

Use the SWING V button to adjust the desired

airflow direction.

When push the SWING V button, the horizontal

louver changes 6 degree in angle for each push.

Keep pushing more than 2 seconds, the louver

will swing automatically and give UP and

DOWN air flow.

NOTE: When the horizontal louver swing

or move to a position which would affect

the cooling or heating effect of the air

conditioner, it would automatically change

the swing/moving direction.

MODE

FAN SPEED

AUTO

COOL

DRY

HEAT

FAN

TEMP.

SET

CLOCK

HOUR

1111

Timer oper ation

press the TIMER ON button can set the auto-on

time of the unit. And press the TIMER OFF button

can set the auto-off time of the unit.

1. Press the TIMER ON button. The remote

controller shows TIMER ON, the last Auto-on

setting time and the signal "HOUR" will be shown

on the LCD display area. Now it is ready to reset

the Auto-on time to START the operation.

2. Push the TIMER ON button again to set desired

Auto-on time. Each time you press the button,

the time increases in 30 minutes increments, up

to 10 hours, then at 1 hour increments up to 24

hours.

3. After setting the TIMER ON ,there will be a one-

half second delay before the remote controller

transmits the signal to the air conditioner. Then,

after approximately another 2 seconds, the

signal "HOUR" will disappear and the set temper-

ature will re-appear on the LCD display window.

To set the Auto-on time.

To set the Auto-off time.

1. Press the TIMER OFF button. The remote

controller shows TIMER OFF, the last Auto-off

setting time and the signal "HOUR" will be shown

on the LCD display area. Now it is ready to

reset the Auto-off time to START the operation.

2. Push the TIMER OFF button again to set desired

Auto-off time. Each time you press the button,

the time increases in 30 minutes increments, up

to 10 hours, then at 1 hour increments up to 24

hours.

3. After setting the TIMER OFF ,there will be a one-

half second delay before the remote controller

transmits the signal to the air conditioner. Then,

after approximately another 2 seconds, the

signal "HOUR" will disappear and the set temper-

ature will re-appear on the LCD display window.

MODE

FAN SPEED

SWING V SLEEP

TIMER ON

TIMER OFF

CLOCK

RESET LOCK

AUTO

COOL

DRY

HEAT

FAN

TEMP.

SET

CLOCK

TIMER

HOU R

ON OFF

SWING H

SELF CLEAN

TURBO

LED

I FEEL

1212

The effective operation time set by the remote controller for the timer

function is limited to the following settings: 0.5, 1.0, 1.5, 2.0, 2.5, 3.0,

3.5, 4.0, 4.5, 5.0, 5.5, 6.0, 6.5, 7.0, 7.5, 8.0, 8.5, 9.0, 9.5, 10, 11, 12, 13,

14, 15,16,17, 18, 19, 20, 21, 22, 23 and 24.

IMPORTANT

Exam ple of Time r sett ing

Start

Off

6 hours later

(Auto-on Operation)

The TIMER ON feature is useful when you want

the unit to turn on automatically before say when

you return home. The air conditioner will automa-

tically start operating at the set time.

To start the air conditioner in 6 hours.

1. Press the TIMER ON button, the last setting of

starting operation time and the signal "HOUR" will

show on the display area.

2. Press the TIMER ON button to display "6.0" on

the TIMER ON display of the remote controller.

3. Wait for 3 seconds and the TIMER ON indicator

stops flashing and this function is activated. The

digital display area will show the tempera ture

again.

TIMER ON

Example:

Set

TIMER

HOUR

1313

Stop

Set 10 hours later

(Auto-off Operation)

The TIMER OFF feature is useful when you want

the unit to turn off automatically after you go to bed.

The air conditioner will stop automatically at the set

time.

To stop the air conditioner in 10 hours.

1. Press the TIMER OFF button, the last setting of

stopping operation time and the signal "HOUR" will

show on the display area.

2. Press the TIMER OFF button to display "10" on

the TIMER OFF display of the remote controller.

3. Wait for 3 seconds and the TIMER OFF indicator

stops flashing and this function is activated. The

digital display area will show the temperature

again.

TIMER OFF

Example:

Stop

2 hours later

after setting

Set

To stop the air conditioner 2 hours after setting

and start it again 10 hours after setting.

1. Press the TIMER OFF button.

2. Press the TIMER OFF button again to

display 2.0 HOUR on the TIMER OFF display.

3. Press the TIMER ON button.

4. Press the TIMER ON button again to

display 10 HOUR on the TIMER ON display .

5. Wait for the remote control to display

the setting temperature.

TIMER OFF TIMER ON

(On Stop Start operation)

This feature is useful when you want to stop the air

conditioner after you go to bed, and start it again in

the morning when you wake up or when you return

home.

Example:

COMBINED TIMER

(Setting both ON and OFF timers simultaneously)

Start

10 hours later

after setting

TIMER

HOUR

OFF

TIMER

HOUR

ON OFF

1414

Example:

TIMER ON TIMER OFF

(Off Start Stop operation)

This feature is useful when you want to start

the air conditioner before you wake up and

stop it after you leave the house.

To start the air conditioner 2 hours after

setting, and stop it 5 hours after setting.

1. Press the TIMER ON button.

2. Press the TIMER ON button again to

display 2.0 HOUR on the TIMER ON display.

3. Press the TIMER OFF button.

4. Press the TIMER OFF button again to

display 5.0 HOUR on the TIMER OFF display .

5. Wait for the remote control to display

the setting temperature.

Off

Stop

Start

2 hours later

after setting

5 hours later

after setting

Set

TIMER

HOUR

ON OFF

The design and specifications are subject to change without prior notice

for product improvement. Consult with the sales agency or manufacturer

for details.

Tel: (305)594-4972 Fax (305) 499 4378

www.klimaire.com [email protected]

2190 NW 89 Place, Doral, FL 33172 - USA

The Klimaire logo is a registered Trademark of Klimaire Products inc.

Klimaire KTIR24H2 User manual

Brand: Klimaire

Model: KTIR24H2

Category: Split-system air conditioners

Type: User manual

This manual is also suitable for

Download PDF

report

Klimaire KTIR24H2 User manual

This manual is also suitable for

Klimaire KTIR24H2 User manual

Related papers

Other documents