Pella 80ML0106 Installation guide

Brand: Pella

Model: 80ML0106

Type: Installation guide

Page 1 of 6

INSTALLATION INSTRUCTION – INSTRUCCIONES DE INSTALACIÓN

DESIGNER SERIES® HINGED GLASS PANEL,

GRILLE, BLIND AND SHADE INSTRUCTIONS

CAUTION:

DO NOT remove or cut the white cord that limits the opening of the hinged

glass panel. Doing so may cause serious damage, including glass breakage, to your

Pella product. The cord should only be detached by a qualiﬁed service technician when

performing service related procedures.

Latch

release

Shade

operator

handle

Latch

release

Casement window is shown.

Part Number: 80ML0106

Table of Contents:

1. Operating the Hinged Glass Panel

2. Grille Removal and Installation

3. Bottom Up Slimshade Blind and Cellular Shade Removal and Installation

4. Tilt Only Slimshade Blind Removal and Installation

5. Top Down Cellular Shade Removal and Installation

Page 2 of 6

OPERATING THE HINGED GLASS PANEL

Note: For products other than venting casement windows,

proceed to Step C.

A. Casement window with ﬂat screen: Remove the ﬂat screen

by unlatching the screen clips and pulling the screen to the

interior.

B. Casement window with Rolscreen: Unlock and open the

sash to 90° so that the hinged panel will not interfere with the

Rolscreen.

C. Locate the latch release(s) on a side or top of the hinged glass

panel. On large panels check the top and bottom for additional

latch releases.

D. Slide each latch release away from the corner(s) of the sash.

You will feel resistance at the latching points. Push past the

resistance. (On venting double-hung windows, slide the latch

release from the center toward one corner then back toward

the opposite corner.)

E. Return the latch releases to the original positions.

Screen Clip

Latch Release

Product

Type

Frame

Height

Number of

Latches

Fixed or Vent

Casement

> 53" 3

≤ 53" 2

Door

> 82.5" 4

≤ 82.5" 3

Latch

DO NOT unhook

or cut cord

F. Open the hinged glass panel. DO NOT unhook or cut the white

cord that restricts the opening of the hinged glass panel.

Note: Hinged glass panels may be hinged on a side or at the bottom

depending on the unit type.

G. Close the hinged glass panel, noting the latch locations. Press

ﬁrmly on the hinged glass panel frame at the latch locations

until you hear a click which indicates the latch has engaged.

Note: Ensure all latches are engaged.

Page 3 of 6

GRILLES

REMOVAL

Follow the steps in Instruction 1 to open the hinged glass panel.

A. Starting at the bottom, grasp the grille as close to the clip at the

end of each bar as possible and pull toward the interior.

B. Repeat step A at the end of each bar.

Note: If the grille has Stand-Offs (large windows and doors with

double pane), or Bumpers (triple pane), DO NOT remove them

from the grille.

INSTALLATION

A. Starting at the top, Align each clip with the dot matrix patterns

imprinted on the frame.

B. Snap the open side of each clip onto the frame by pressing on

the clip.

Grille

Stand-Off

Grille

Bumper

Grille

Clip

Grille

Bar

Dot

Matrix

Pattern

Grille

Stand-Off

Grille

Bumper

Grille

Clip

Grille

Bar

BOTTOM UP SLIMSHADE®

BLIND AND CELLULAR SHADES

Note: Follow the steps in Instruction 1 to open the hinged glass panel.

Follow the steps in Instruction 2 to remove the grilles (if applicable).

REMOVAL

Note: Remove the two cardboard end caps and other packaging from

the blind/shade (if applicable), do not cut cords, shade cloth or

damage blinds.

A. Place the blind/shade in the full open position.

B. For shades 47” or wider only: Remove the shade support clip

located near the center of the shade mounting channel. Remove the

clip from the bottom of the mounting channel, then remove the clip

from the hinged glass panel.

C. Release the blind/shade from the mounting stud by pulling the

plastic tab.

D. Remove the blind/shade head rail from the drive gear and second

mounting stud by sliding it away from the operator side of the

hinged glass panel.

INSTALLATION

A. Make sure the shade operator handle is near the bottom

of the hinged glass panel. This allows for full travel of the

operator handle to raise or lower the blind/shade completely.

B. To install the blind/shade, slide the operator end of the top

rail over the mounting stud, while guiding the operator drive

into the drive gear. This end is labeled "A" on the top of the

head rail. It may be necessary to move the shade operator

handle up slightly to help align the gear.

Drive

Gear

Mounting Stud

Head Rail

Operator Drive

Plastic Tab

Shade Support Clip

Page 4 of 6

C. Press the opposite end of the rail over the second mounting stud.

Note: Bottom-up cellular shades may appear to be too short for the unit. The shade will lengthen

after hanging in the down position for a few hours. If the shade does not hang straight, open

and close it completely two to three times.

D. For shades 47" or wider: Attach the shade support clip to

the top of the hinged glass panel near the center of the

hinged glass panel. However, if there is a grille that will be

attached at the center point, move the support to the left

or right of center. Next, lift up on the shade head rail, to

engage the clip.

Note: Follow the steps in Instruction 1 to open the hinged glass

panel. Follow the steps in Instruction 2 to remove the grilles

(if applicable).

REMOVAL

A. Slip the metal support clips off the hinged glass panel

frame.

B. Release the blind from the mounting stud by pulling the

head rail.

C. Remove the blind head rail from the drive gear and second

mounting stud by sliding it away from the operator side of

the hinged glass panel.

INSTALLATION

Note: Remove the plastic bands and foam pads from the blind (if applicable), do not cut cords or

damage the slats. With one hand, compress the blind while removing the banding and foam

pads, then remove the cord from the cardboard spool. Grasp the bottom rail, and gently pull

down until the bottom rail almost touches the bottom of the hinged glass panel.

A. Install the bottom rail retainers. (If the bottom rail retainers are already in place, proceed to

Step B.) Pull the tape from the “LH” retainer and place it approximately 1/4" from the left end of

the hinged glass panel bottom rail as shown. Repeat this process for the “RH” retainer, placing it

at the right end of the hinged glass panel bottom rail.

B. Check the location of the shade operator handle. Ensure that it is located at least 4" above or

below one of the hinged glass panel latches. This allows for sufﬁcient travel of the operator

handle to tilt the blind completely.

Shade Support

Clip

Grille

Bar

TILT ONLY SLIMSHADE BLINDS

BOTTOM UP SLIMSHADE®

BLIND AND CELLULAR SHADES (CONTINUED)

Page 5 of 6

C. Install the blind by sliding the operator end of the head rail

over the mounting stud while guiding the operator drive into

the drive gear.

D. Secure the head rail by pressing the opposite end of the rail

over the second mounting stud.

E. There will be up to six support clips depending on the

width of the blind. Space the support clips evenly between

the cord ladders along the head rail. Do not cover locations

where grilles will be installed. Press the top of the clip onto

the hinged glass panel frame.

F. Place the shade bottom rail between the glass of the hinged

glass panel and the legs of the bottom rail retainer.

TILT ONLY SLIMSHADE BLINDS (CONTINUED)

Note: Follow the steps in Instruction 1 to open the hinged glass panel.

Follow the steps in Instruction 2 to remove the grilles (if applicable).

REMOVAL

A. Place the shade in the full open position.

B. For shades 47" or wider only: Remove the center shade support clip

by taking it off of the mounting channel, then remove the clip from

the hinged glass panel.

C. Release the blind/shade from the mounting stud by pulling the

plastic tab.

D. Remove the shade head rail from the drive gear and second

mounting stud by sliding it away from the operator side of the

hinged glass panel.

Note: Take care to avoid tangling the internal cords as the shade is

removed from the window.

Plastic Tab

Shade Support Clip

TOP DOWN CELLULAR SHADES

Page 6 of 6

INSTALLATION

Note: Remove the two cardboard end caps and other packaging from the blind/shade (if

applicable), do not cut cords, shade cloth or damage blinds.

Hold the compressed shade while removing the banding, then gently lower the compressed shade

until it reaches the bottom of the hinged glass panel.

A. Ensure the operator handle is near the bottom of the hinged glass panel prior to inserting the

blind/shade. This allows for full travel of the operator handle to raise or lower the blind/shade

completely.

B. Insert the shade into the hinged glass panel frame by

sliding the operator end of the head rail over the mounting

stud while guiding the operator drive into the drive gear. It

may be necessary to move the shade operator handle up

slightly to help align the gear.

C. Secure the shade head rail by pressing the opposite end of

the rail over the second mounting stud.

Shade Support

Clip

Grille

Bar

WARNING

TOP DOWN CELLULAR SHADES (CONTINUED)

D. For shades 47" or wider: Attach the shade support clip

to the top of the hinged glass panel near the center of

the hinged glass panel. However, if there is a grille that

will be attached at the center point, move the support to

the left or right of center. Next, lift up on the shade head

rail, to engage the clip.

Drive

Gear

Mounting Stud

Head Rail

Operator Drive

Pella 80ML0106 Installation guide

Pella 80ML0106 Installation guide

Pella 80ML0106 Installation guide

Related papers

Other documents