Home Styles 5001-0043 Assembly Instructions

Brand: Home Styles

Model: 5001-0043

Type: Assembly Instructions

88 5001 006

Buffet

Home Styles Consumer Assistance : www.homestyles-furniture.com,

[email protected], 888-680-7460, 877-831-0319

Hardware List

Part List

IMPORTANT NOTE

Carefully remove all the parts from the carton and put

them individually on a soft cloth to prevent scratches

or other damage occurring to the parts.

We have taken great care in the design of this

product and request that you carefully and strictly

follow our assembly instructions to ensure

a completed product as it was designed.

Tools required for assembly : Phillips screwdriver, Drill, 3/8” Drill Bit Level,

(Please refer to the last page of these

instructions for drawer assembly steps.)

Side Panel

1 Pc.

Side Panel

1 Pc.

Front Stretcher

1 Pc.

Front Stretcher

1 Pc.

Back Stretcher

1 Pc.

Base

1 Pc.

Front Upright

1 Pc.

Divider

1 Pc.

Back Upright

1 Pc.

Leg

2 Pcs.

Back Stretcher

1 Pc.

Back Panel

2 Pcs.

Shelf

1 Pc.

Drawer

M6x35

Head Cap Bolt

4 Pcs. (+1 extra)

Cam Lock

10 Pcs. (+2 extra)

Cam Lock Screw

10 Pcs. (+1 extra)

M3.5x13

Wood Screw (short)

for Base Drawer

8 Pcs. (+1 extra)

M3.5x16

Wood Screw

for Back Panel

8 Pcs. (+1 extra)

M4x25

Machine Screw

6 Pcs.

Small Hex Wrench

1 Pc.

M6x50

Head Cap Bolt (long)

4 Pcs. (+1 extra)

Cross Dowel

4 Pcs. (+1 extra)

M3.5x25

Wood Screw (long)

for Side Drawer

16 Pcs. (+1 extra)

Adjustable Pin

4 Pcs. (+2 extra)

Pull Handle

2 Pcs.

Knob

2 Pcs.

Hex Wrench

1 pc.

2 Pcs.

Door

1 Pc.

Door

1 Pc.

Assembly Instructions 2/5

IMPORTANT

* Please keep Hex Wrench in a safe place as you may need to tighten up the Head Cap Bolts in the future.

* Do not tighten up all the bolts until each part is properly assembled.

* Use a soft cloth between these parts and the floor.

* After assembly, item must be level to work properly. Use the included adjustable levelers to level.

Back Stretcher (I).

Slide Back Panels (J) into place.

Attach unit from Step 3 to unit.

Attach Side Panels (A) and (B) to

unit with Cam Locks.

(See Figure 2)

Figure 1

Figure 2

Cam Lock Screw

Cam Lock

of Side Panels (A) and (B) and then tighten.

Assembly Instructions 3/5

Cross Dowel

Head Cap Bolt (long)

Cam Lock Screw

Wood Screw

for Back Panel

Head Cap Bolt

Cross Dowels and

Head Cap Bolts (long).

Attach Legs (L) to Base (K) with

Head Cap Bolts.

Figure 3

Figure 4 Figure 5 Figure 6

Note : Please make sure unit is level before tightening these screws.

Cam Lock

lift hinges. (See Figure 5)

To level the unit, adjust the adjustable levelers on the

bottom of unit (See gure 6)ﬁ

Attach Door (N) and (O) to side panels by

sliding the door lift hinges into the side panel

Attach Top to unit with Cam Locks.

Insert Adjustable Pins into side panels at

the desired level.

Place Shelf (M) into position.

Attach Knobs to Door (N) and (O) with

Machine Screws. (See Figure 4)

Adjustable Pin

M3.5x13

Wood Screw

1 pc.(+1 extra)

Anchor

1 pc.(+1 extra)

Bracket

2 pcs.(+1 extra)

Tipover Restraint

1 pc.(+1 extra)

Hardware List

M3.5x40

Wall Screw

1 pc.(+1 extra)

Assembly Instructions 4/5

Wood Screw

Wall Screw

Attention!

To help reduce the risk of the unit tipping over, the Tipover Restraint be installed followingmust

these instructions exactly!

tie end

loop end

Place unit at desired location.

Drill a hole in wall3/8”

at the appropriate location.

Insert Anchor into the wall hole

and attach Bracket with Wall Screw.

Attach Bracket at pre-drilled hole at top

of unit with Wood Screw.

Use Tipover Restraint to secure Bracket

on unit to Bracket on wall.

(See Figure X)

Put tie end of Tipover Restraint into loop end

of Tipover Restraint and pull until tight.

Figure X

Bracket

on wall

Anchor in wall

3/8” wall hole

Bracket at

top of unit

Tipover

Restraint

Top of unit

Drill 3/8” hole in wall

Assembly Instructions 5/5

Part List

Front Part

2 Pcs.

P2.

Back Part

2 Pcs.

P3.

Side Part

2 Pcs.

P4.

Side Part

2 Pcs.

P5.

Base Part

2 Pcs.

Figure 1

Figure 2

Figure 3

Figure 4

screwdriver and long Wood Screws (4X),

tighten halfway.

Attach P2 to P3 and P4 using long Wood

push P5 all the way forward so it meets P1.

(See Figure 2)

holes in P5, tighten screws.

(See Figure 4)

Tighten all screws used in drawer assembly.

Drawer

P1.

Home Styles 5001-0043 Assembly Instructions

Home Styles 5001-0043 Assembly Instructions

Home Styles 5001-0043 Assembly Instructions

Related papers

Other documents