Kodak I1220 - Document Scanner Quick Tips

Brand: Kodak

Model: I1220 - Document Scanner

Type: Quick Tips

This manual is also suitable for

CLEANING THE ROLLERS

The scanner transport rollers and imaging area should be

cleaned routinely for optimum performance. Some paper

types and operating environments require cleaning more

often then specified in the User’s Guide.

1. Turn off the scanner.

2. Open the scanner cover.

3. With a roller cleaning pad, wipe the rollers from side to

side. Rotate the rollers to clean the entire surface.

IMPORTANT:The Roller Cleaning Pad contains sodium

lauryl ether sulfate which can cause eye

irritation. Refer to the MSDS for more

information.

4. Dry the rollers with a lint-free cloth.

CLEANING OR REPLACING THE SEPARATION

MODULE

1. Open the scanner cover.

2. Push the separation module release lever down and

lift the separation module up and out of position.

3. Manually rotate and wipe the separation module tires

with a roller cleaning pad.

4. Inspect the separation module. If the tires show signs of

wear or damage, replace the tires or the separation

module.

5. Insert the separation module by aligning the pins and

placing it into position.

CLEANING THE IMAGING AREA

1. Remove dust and debris from this area by using a Stati-

cide wipe or a small brush. Be careful not to scratch the

imaging area when cleaning

IMPORTANT:Staticide wipes contain isopropanol which can

cause eye irritation and dry skin. Wash your

hands with soap and water after performing

maintenance procedures. Refer to the MSDS

for more information.

2. Wipe the upper and lower imaging area again with an

almost-dry Staticide wipe to remove any streaks

SUPPLIES*

* Items are subject to change.

EASTMAN KODAK COMPANY

343 State Street

Rochester, New York 14650 U.S.A.

A-61561 / Part #9E4867 August, 2007

TM: Kodak

i1200/i1300 Series Scanners

Quick Tips

www.kodak.com

Kodak Service

1-800-822-1414

Kodak Parts Services

1-800-471-0803

1-585-724-6042

Kodak Professional Services

1-800-525-6325

CAT No. Description

148 4864 Kodak Feed Rollers for i1200/i1300

Series Scanners

173 6115 Kodak Separation Module for i1200/

i1300 Series Scanners

826 9607 Kodak Feed Module for i1200/i1300

Series Scanners

853 5981 Kodak Digital Science Roller Cleaning

Pads (qty 24)

896 5519 Staticide Wipes for Kodak Scanners

(qty 144)

INDICATOR LIGHTS AND ERROR CODES

Indicator light — illuminates or flashes indicating scanner

status.

Steady green: scanner is ready to scan.

Steady red: indicates a scanner error; such as, the

scanner cover is open or a document jam, etc.

Flashing green: waiting/Energy Star mode; scanning/busy.

Flashing red: scanner failure.

POWER SWITCH AND CONNECTORS

Power switch — turns the scanner on and off.

Power port — connects the power cord to the scanner.

USB port — connects the scanner to the PC.

Flatbed port — connects the tethered flatbed accessory to

the scanner.

Security lock port — connects a security lock to the

scanner.

CLEANING AND MAINTENANCE

For detailed cleaning and replacement procedures, see the

User’s Guide, Chapter 5, Maintenance.

OPENING THE SCANNER COVER

1. Turn off the scanner.

2. Press the scanner cover release lever and pull the

scanner cover down.

3. Close the cover when finished cleaning the scanner or

replacing parts.

4. Turn on the scanner.

CLEANING OR REPLACING THE FEED

MODULE

1. Open the scanner cover.

NOTE: The paper present sensor is located to the right

of the feed module. Be careful not to damage

the paper present sensor when removing or

cleaning around the feed module.

2. Push against the raised edge of the feed module cover

and lift it up and out of position.

3. Rotate the feed module upward and push it to the left to

lift it out of position.

4. Manually rotate and wipe the feed module tires with a

roller cleaning pad.

5. Inspect the feed module. If the tires show signs of wear

or damage or multi-feeds continue to occur after

cleaning, replace the tires or feed module.

6. Using a vacuum or cleaning pad, remove dust and

debris from the feed module area.

7. Insert the feed module by aligning the pins and pushing

it toward the left to fit it into position. Be sure the gears

are aligned and it snaps into place.

8. Reinstall the feed module cover by aligning the tabs in

the slots and pushing the feed module cover down until

it snaps into place.

Error Code Description

0 USB cable is not connected

1-5,

7 and 8

Call Service

6 The scanner cover is open

9 Document jam

Power switch

USB port

Power port

Flatbed port

Security lock port

Kodak I1220 - Document Scanner Quick Tips

Brand: Kodak

Model: I1220 - Document Scanner

Type: Quick Tips

This manual is also suitable for

Download PDF

report

Kodak I1220 - Document Scanner Quick Tips

This manual is also suitable for

Kodak I1220 - Document Scanner Quick Tips

Related papers