SMART Technologies SMART Board 3000i Installation guide

SMART Technologies
Brand
SMART Technologies
Model
SMART Board 3000i
Type
Installation guide

This manual is also suitable for

SMART Technologies SMART Board 3000i is an interactive whiteboard that allows you to control your computer and interact with digital content using your finger or a pen. It is ideal for use in classrooms, meeting rooms, and other collaborative environments.

Capabilities:

  • Write, draw, and annotate on the screen using your finger or a pen
  • Control your computer's mouse and keyboard from the screen
  • Open and interact with files, applications, and websites
  • Collaborate with others in real time, even if they are remote
  • Save your work to a variety of file formats, including PDF, PowerPoint, and SMART Notebook

SMART Technologies SMART Board 3000i is an interactive whiteboard that allows you to control your computer and interact with digital content using your finger or a pen. It is ideal for use in classrooms, meeting rooms, and other collaborative environments.

Capabilities:

  • Write, draw, and annotate on the screen using your finger or a pen
  • Control your computer's mouse and keyboard from the screen
  • Open and interact with files, applications, and websites
  • Collaborate with others in real time, even if they are remote
  • Save your work to a variety of file formats, including PDF, PowerPoint, and SMART Notebook
Rear Projection SMART Board 3000i Interactive Whiteboard Setup
1
Rear Projection SMART Board
™
3000i Interactive
Whiteboard Setup
WARNING: Two people are required to perform the following procedures.
1. Cut the shipping bands and remove the cardboard covering and plastic wrap from around the
cabinet.
2. Remove the band that holds the pallet ramp against the touch screen. Lower the pallet ramp.
Pallet Ramp
Cut this band
Touch Screen
2
Rear Projection SMART Board 3000i Interactive Whiteboard Setup
3. Remove the cardboard and plastic wrapping.
NOTE: Do not remove the foam-lined cardboard that protects the rear surface of the touch
screen. Only remove this protective cardboard when you are ready to mount the screen onto
the cabinet.
4. To remove the screen from the four angle brackets, loosen and remove the four corner hex-
cap screws that secure the screen to the four brackets. Then lift the screen off the top
standoff posts and carefully move it to one side.
5. Using a Phillips® No. 2 screwdriver, loosen the four captive corner screws that secure the
cabinet top to the angle brackets.
Captive Fasteners
Touch Screen
Foam-Lined
Cardboard
Angle Bracket × 4
Cardboard Cover
Rear Projection SMART Board 3000i Interactive Whiteboard Setup
3
6. Carefully lift the top half of the cabinet off the bottom half. To prevent damage or mirror
misalignment, turn the upper cabinet right side up, so that only the four corner pins on its
bottom surface make contact with the floor.
7. Remove the piece of wood with two angle brackets attached to the bottom of the cabinet by
removing the two bolts on either end.
8. Using the 9/16" wrench provided (you'll find it attached to the pallet) remove the bolts that
secure the four orange shipping brackets that hold the bottom half of the cabinet to the pallet.
You can also remove the four angle brackets from the pallet, if necessary. You can now
wheel the lower cabinet down the pallet ramp.
Orange Shipping Brackets × 4
Wood with Angle Brackets
Angle Brackets × 4
Bolt Locations
4
Rear Projection SMART Board 3000i Interactive Whiteboard Setup
9. With each person lifting the cabinet top by a side handle with one hand while supporting it
with the other hand, carefully maneuver the four bottom-corner pins over the holes in the
lower half of the cabinet and gently lower it into place.
10. Using the hex key provided in the accessory kit, insert and tighten two of the four supplied
security screws to the underside of the top cabinet, on either side of the pen tray.
He
x
Ke
y
Rear Projection SMART Board 3000i Interactive Whiteboard Setup
5
11. Using the same hex key, secure the remaining two security screws inside each side handle.
12. Before attaching the screen, remove the protective cardboard liner from the back of the
screen. Then, with each person holding the screen by the top and bottom corners, carefully
hang the screen by inserting the two upper-corner standoff posts into the corresponding
keyholes on the cabinet.
CAUTION
Do not, under any circumstances, touch the rear surface of the screen. If a mark
has been made on its surface, dab it gently with a soft cloth that’s been sprayed
with standard, alcohol-free glass cleaner. Do not apply the cleaner directly to the
surface.
Do not apply isopropyl alcohol, water or acetone to the rear surface of the touch
screen. Any of these fluids will damage the diffusion coating, resulting in a
permanent deterioration in display quality.
Location of
Standoff Post
Keyhole × 2
99-261-00 REV D0
SMART Technologies Inc.
1207 - 11 Avenue SW, Suite 300
Calgary, AB T3C 0M5
CANADA
Support +1.403.228.5940 or Toll Free 1.866.518.6791 (Canada/U.S.)
Support Fax +1.403.806.1256
[email protected] www.smarttech.com
© 2001–2006 SMART Technologies Inc. All rights reserved. The SMART logo is a trademark of SMART Technologies Inc. All other third-party product and company
names may be trademarks of their respective owners. Contents are subject to change without notice. 02/2006.
13. Facing the front of the cabinet, pull the bottom of the screen slightly towards you and attach
the modular cable to the RJ45 connector, and the power cable to its connector on the
communications hub.
14. Using a Phillips No. 2 screwdriver, tighten the four captive fasteners in the rear corners of the
screen, starting with the two at the top. Press firmly on the screwdriver to avoid damaging the
screw heads.
Communications Hub
Modular Cable
RJ45 Connector
Power Cable
Power
Connector
Captive
Corner
Fasteners
  • Page 1 1
  • Page 2 2
  • Page 3 3
  • Page 4 4
  • Page 5 5
  • Page 6 6

SMART Technologies SMART Board 3000i Installation guide

SMART Technologies
Brand
SMART Technologies
Model
SMART Board 3000i
Type
Installation guide
This manual is also suitable for

SMART Technologies SMART Board 3000i is an interactive whiteboard that allows you to control your computer and interact with digital content using your finger or a pen. It is ideal for use in classrooms, meeting rooms, and other collaborative environments.

Capabilities:

  • Write, draw, and annotate on the screen using your finger or a pen
  • Control your computer's mouse and keyboard from the screen
  • Open and interact with files, applications, and websites
  • Collaborate with others in real time, even if they are remote
  • Save your work to a variety of file formats, including PDF, PowerPoint, and SMART Notebook
Download PDF
report

Ask a question and I''ll find the answer in the document

Finding information in a document is now easier with AI

Related papers

Other documents