RADIO REMOVAL
1. Pull down glove box and remove.
2. Locate and release climate control cable.
3. On drivers side under dash, locate and release
climate control cable.
4. Carefully pry out on radio and climate control
dash bezel, disconnect and remove from dash.
5. Remove radio removal access panels
on either side of radio.
6. Using two sets of radio removal tools
(DT-1) release, disconnect, and
remove radio from dash.
© 2005 SCOSCHE INDUSTRIES, INC.
SI 1/05-MA1537B (3000376)
If you have any further questions, call our toll free technical help line at: 1-800-621-3695x3
MA1537B
IN-DASH INSTALLATION KIT FOR
1995-03 SELECT MAZDA VEHICLES
LIABILITY DISCLAIMER
This instruction booklet is based on carefully documented data and research of automobile dash
disassembly, wire harness/codes and information pertaining to installation of this kit (MA1537B) in
2001-UP Select Mazda Vehicles. Scosche Industries, Inc. can not be held responsible for
discrepancies/inconsistencies that may occur due to the automobile manufacturing changes or
options, or damage that may occur in the automobile during the installation of components while
using this booklet.
For Factory Wiring Codes go to:
www.scosche-cars.com
FACTORY WIRING CODES
5179
TRIM RING
5125 POCKET
5178 MOUNTING PANEL
2
Thank you for purchasing the Scosche MA1537B Kit. This kit was manufactured with the highest of
quality standards.
CAUTION:
DISCONNECT YOUR VEHICLE'S NEGATIVE BATTERY TERMINAL BEFORE THE INSTALLA-
TION TO HELP PREVENT ELECTRICAL DAMAGE. WE RECOMMEND THE USE OF A VOLT/
OHM METER OVER A TEST LIGHT TO CHECK WIRING. A TEST LIGHT OR GROUNDED WIRE
PROBE CAN CAUSE DAMAGE TO THE VEHICLE'S COMPUTER AND/OR DIAGNOSTIC
SYSTEMS. AVOID ALL FACTORY AIR BAG WIRING - AIR BAGS CAN ACCIDENTALLY DEPLOY
CAUSING SERIOUS INJURY OR DEATH.
NOTES:
• See your vehicle's instructions for any special tools your installation might require.
• Read all instructions accompanying your car stereo/cassette player for proper wiring and mounting
instructions.
INTRODUCTION / PRELIMINARY
MOUNTING THE RADIO
MA1537 KIT
REAR
SUPPORT
ISO
MOUNT
RADIO
BEND TABS
OUTWARD
1998-03 MAZDA 626
RADIO REMOVAL
NOTE: The factory radio provision is a DIN radio.
1. Carefully remove plastic covers on radio sides.
2. Using two sets of radio removal tools (DT-1) release, disconnect, and remove radio from dash.
1995-03 MAZDA MILLENIA
RADIO REMOVAL
NOTE: The factory radio provision is a DIN radio.
1. Carefully remove plastic covers on radio sides.
2. Use Scosche DT-1 DIN removal tools to release radiio, lift away, disconnect and remove.
1999-03 MAZDA PROTÉGÉ
RADIO REMOVAL
NOTE: The factory radio provision is a DIN radio.
1. Carefully remove plastic covers on radio sides.
2. Use Scosche DT-1 DIN removal tools to release radiio, lift away, disconnect and remove.
2002-03 MAZDA PROTÉGÉ 5
RADIO REMOVAL
NOTE: The factory radio provision is a DIN sized radio .
1. Pull glove box down and remove, disconnect climate control cable from lever.
2. Disconnect climate control cable on driver's side under dash above gas pedal.
3. Remove radio's end caps.
4. Insert two sets of Ford DIN removal tools to release clips, pull radio out, disconnect and remove. (We
recommend the Scosche DT-1 Ford DIN removal tools).
CAUTION:
REAR SUPPORT AVAILABLE SEPARATELY.
REAR SUPPORTING THE RADIO ADDS TO THE
INSTALLATIONS STRUCTURAL INTEGRITY.
VEHICLE APPLICATIONS
1998-03 MAZDA 626 ------------------------ 2
1995-03 MAZDA MILLENIA -------------- 2
1999-03 MAZDA PROTÉGÉ -------------- 2
2002-03 MAZDA PROTÉGÉ 5 ------------ 2
5324
REAR SUPPORT
-
1
Ask a question and I''ll find the answer in the document
Finding information in a document is now easier with AI
Related papers
Other documents
-
Lund Industries FE-CSMTS User manual
-
PAC MAZK854 User manual
-
-
PAC FMK550 User manual
-
Metra 99-5700 Installation guide
-
Metra Electronics 99-5512 User manual
-
Metra 99-5804 Installation guide
-
-
Metra 88-00-9000 Operating instructions
-
Metra Electronics 95-5600 User manual
