Technical Instructions 7003.L
10/2013 U RONDA AG, Lausen, Switzerland, Phone ++41 (0)61 926 50 00, www.ronda.ch, [email protected] 1
2000.669.G Main
1.
3305.362.CO Cannon pinion with driver (Aig.1)
2.
A
2030.027.CO Centre bridge
3.
Centre bridge held by 5 screws 4000.250.
4000.250 Screw
4.
2130.181.CO Combined maintaining plate
5.
Combined maintaining plate held by 1 screw 4000.250.
4000.250 Screw
6.
B
3016.028 Lever for setting lever
7.
Lever for setting lever held by 1 screw 4000.249.
4000.249 Screw
8.
3016.027 Stop lever
9.
Stop lever held by 1 screw 4000.249.
4000.249 Screw
10.
3622.044 Stator
11.
3715.105.RK Rotor
12.
3147.060.CO Intermediate wheel
13.
3122.070.CO Third wheel
14.
3136.177.CO Centre second wheel (Aig.1)
15.
C
Technical Instructions 7003.L
10/2013 U RONDA AG, Lausen, Switzerland, Phone ++41 (0)61 926 50 00, www.ronda.ch, [email protected] 2
2020.169.G Train wheel bridge
16.
Train wheel bridge held by 3 screws 4000.244.
4000.244 Screws
17.
3603.080 Battery insulator
18.
3601.120.G Battery clamp +
19.
Battery clamp held by 1 screw 4000.248.
4000.248 Screw
20.
3503.071 Tube
21.
D
3612.195 Electronic module
22.
Electronic module held by 4 screws 4000.250.
4000.250 Screw
23.
3603.081 Spacer
24.
E
2130.182.G.M01.7003L Electronic module cover
25.
Electronic module cover held by 4 screws 4000.244.
4000.244 Screws
26.
3600.032.HGF Battery 381
27.
F
Technical Instructions 7003.L
10/2013 U RONDA AG, Lausen, Switzerland, Phone ++41 (0)61 926 50 00, www.ronda.ch, [email protected] 3
2000.669.G Main Plate
28.
3017.054.CO Setting lever
29.
3905.063 Setting lever jumper (3 positions)
30.
Setting lever jumper held by 1 screw 4000.282. Tensioning the spring
arm.
4000.282 Screw
31.
3001.061.FI Sliding pinion
32.
G
3015.077 Yoke (3 positions)
33.
Tensioning the spring arm.
3004.200 Corrector setting wheel
34.
3004.200 Corrector setting wheel
35.
3015.078.CO Rocking bar (3 positions)
36.
Tensioning the spring arm.
H
2130.194 Setting mechanism cover
37.
Setting mechanism cover held by 4 screws 4000.305.
4000.305 Screws
38.
3000.194.CO Setting stem
39.
3004.204 Intermediate setting wheel
40.
3007.079.CO Minute wheel
41.
2130.185 Minute train bridge
42.
Minute train bridge held by 1 screw 4000.278.
4000.278 Screw
43.
3301.296.CO Hour wheel retro (Aig.1)
44.
3147.066.CO Date corrector setting wheel
45.
I
Technical Instructions 7003.L
10/2013 U RONDA AG, Lausen, Switzerland, Phone ++41 (0)61 926 50 00, www.ronda.ch, [email protected] 4
2000.671.G Main plate retro (6h)
46.
Main plate retro held by 4 screws 4000.248
4000.248 Screw
47.
3004.220 Tens indicator driving wheel
48.
The short tooth of the tens indicator driving wheel must point to the
center of the movement.
3500.072 Tens jumper
49.
J
2130.187 Tens jumper maintaining plate
50.
Tens jumper maintaining plate held by 2 screws 4000.279. Tensioning
the spring arm.
4000.279 Screw
51.
3004.208.CO Date indicator driving wheel
52.
3147.061 Intermediate date wheel
53.
3404.005.CO Day cam (6h)
54.
Place parts as shown on graphics.
3406.032 Day rack
55.
3406.031 Day rack lever
56.
3507.059.CO Date corrector wheel
57.
K
2130.188 Date indicator plate
58.
3905.068 Date corrector spring
59.
Date corrector spring held by 1 screw 4000.244.
3905.066 Day rack lever spring
60.
3500.069 Day jumper
61.
Tensioning the spring arm.
3500.068 Date jumper
62.
3504.229.AF.1.A Units indicator (standard)
63.
Nick of the indicator at 3 o`clock.
L
Technical Instructions 7003.L
10/2013 U RONDA AG, Lausen, Switzerland, Phone ++41 (0)61 926 50 00, www.ronda.ch, [email protected] 5
2130.189 Date indicator maintaining plate
64.
Date indicator maintaining plate held by 1 screw 4000.250.
4000.250 Screw
65.
3905.064 Date jumper spring
66.
Insert the date jumper spring in the provided opening.
3907.047 Day finger flange
67.
Stem pos III: Turn crown forwards until the date jumps. Stem pos II:
Move the date until the nick is at 3 o`clock.
3004.211 Day finger
68.
Position the end of the teeth against the day came pinion while turning
softly in counterclockwise direction.
M
3004.212 Days driving wheel
69.
Insert the tooth of the wheel in the flange gap, while turning softly in
counterclockwise direction to ensure correct position of the day finger.
3401.082.FI Day indicator pinion
70.
3147.062 Tens intermediate wheel
71.
Arrow positioning radially outwards.
3315.003 Friction spring
72.
N
3504.230.AF.1.A Tens indicator (standard)
73.
Nick of the indicator at 3 o`clock.
2130.190.G Date mechanism maintaining plate
74.
Date mechanism maintaining plate held by 3 screws 4000.320.
4000.320 Screw
75.
3506.077.G Intermediate dial support
76.
Polished version first.
3506.076.G Dial support
77.
O
8200 Moebius 8200
78.
9014 Moebius 9014
79.
124 Jismaa 124
80.
9020 Moebius 9020
81.
10/2013 RONDA AG, Lausen, Switzerland, Phone ++41 (0)61 926 50 00, www.ronda.ch, [email protected] EM 1
Electronic measurements
7003.L
Battery
381
Voltage
1.55 V
Setting stem in p
osition I, calendar not in gear,
60 s measur
ing interval for rate and consumption:
Typ
ical consumption
Maximal
consumption
1.32 µA
3.10 µA
R
ate
-10s/M. .. +20s/M.
Lower working voltage limit
1.20 V
Setting stem in position
III, 60 s measuring interval:
Typical consumption
Maximal consumption
0.10 µA
0.30 µA
/
