[SPECIFICATION]
*Cal VD34
Cal.VD33 without calendar
3 Hands ( Hour , Minute , Second )
Dual time of 12 hour regulator hand
Dual time of 60 minute regulator hand
24 hour hand , Calendar (Cal.VD33 only)
Two pole stepping motor
Step motor 2 pieces
Electronic circuit reset switch
Second setting device
Date setting (Cal.VD33 only)
Time difference correction
[ Time ]
Indicated by Hour , Minute , Second and 24 hour hands
Dual time of 12 hour regulator and dual time of 60 minute regulator hands
[ Dual time of 12 hour regulator and dual time of 60 minute regulator ]
±1hour / push
SR920SW (Silver oxide battery)
Battery life is approximately 2 years
Use 10-second gate
*Set the winding stem with crown at the normal position
0 Jewel
Cal.
PARTS CATALOGUE / TECHNICAL GUIDE
Cal. No.
Item
Cal.VD33&VD34
Version-01
VD33&VD34
Time indication
Outside diameter
Driving System
Casing diameter
φ29.50 mm × 26.00 mm (3H-9H)
Cal.VD33...4.57 mm
Cal.VD34…3.97 mm
φ28.80 mm
Total height
Free
Movement
Movement
size
1
SII Products
Less than ± 20seconds : Monthly rate at normal temperature range
1600A/m
Jewels
Measuring gate by
quartz tester
Battery
Accuracy
First
click
Left rotation
Right rotation
-1hour/push Time difference correction
Additional mechanism
+1hour/push Time difference correction
Buttons
Antimagnetic
Button B
VD33 VD34
Free
Free
Date setting
Time setting with stop-second device
Time setting with stop-second device
Normal position
Crown
position
Button A
Second click
0012 079
0808 368 …Cal.VD33 only Auxiliary train wheel bridge screw
Date dial guard
Date dial …Cal.VD33 only
Refer to page 5 for each parts code
Auxiliary train wheel bridge
Refer to page 5 for each parts code
0806 368 …Cal.VD33 only
Date corrector wheel
0810 368 …Cal.VD33 only
Date jumper
Small hour hand wheel
Refer to page 5 for each parts code
0737 891 …Cal.VD33 only
Refer to page 5 for each parts code
0836 369 …Cal.VD33 only
0886 003 Intermediate wheel for date
Intermediate 12 hours wheel corrector holder
and pinion (B)
0962 891 …Cal.VD33 only
12 hours wheel
Refer to page 5 for
each parts code 0962 891 …Cal.VD33 only
0886 001
Intermediate 12 hours
wheel and pinion (A)
0885 002
Hour wheel
Refer to page 5 for
each parts code
Small minute wheel
Refer to page 5 for
each parts code
PARTS CATALOGUE
Version-02
VD33&VD34
Intermediate wheel for date corrector (D)
SII Products
Intermediate small minute wheel
Intermediate wheel for date corrector (B)
2
Intermediate wheel for date corrector (C)
Type of oil Oil quantity mark
Moebius 9010 NORMAL QUANTITY
Moebius 9030 SUFFICIENT QUANTITY
Disassembling procedures Figs.
Reassembling procedures Figs.
Battery
Winding stem
Cal.VD33 …0351 177
0012 079 Cal.VD34 …0351 178
Switch spring screw
0012 079
Switch spring screw
Switch spring
Cal.VD33 …4250 332
Cal.VD34 …4250 342
4004 331
Circuit block
0012 079
Train wheel bridge (B) screw
0125 331 4270 358
Train wheel bridge (B) Battery connection (-)
4146 177
Step rotor (B)
4002 923
Coil block (B)
4239 357
Rotor stator (B)
0701 014
Fifth wheel and pinion (B)
*All parts code are subject to changewithout notice.
PARTS CATALOGUE
Version-04
VD33&VD34
SII Products
3
Type of oil Oil quantity mark
Moebius 9010 NORMAL QUANTITY
Moebius 9030 SUFFICIENT QUANTITY
0125 248
Train wheel bridge (A)
Fourth wheel and pinion
Refer to page 5 for each parts code
0701 904
Fifth wheel and pinion (A)
0231 904
Third wheel and pinion
4146 890
Step rotor (A)
0261 034
Minute wheel and pinion
Center wheel and pinion
Cal.VD33 …0221 157
Cal.VD34 …0221 156
0281 904
Setting wheel
Train wheel setting lever
4002 904 Refer to page 5 for each
Coil block (A) parts code
Setting lever
Refer to page 5 for
each parts code
0384 470
Yoke
4239 357
Rotor stator (A) 0282 890
Clutch wheel
Intermediate wheel for
*All parts code are subject to changewithout notice. date corrector (A)
SII Products
4
0962 890 …Cal.VD33 only
PARTS CATALOGUE
Version-04
VD33&VD34
*1
*1
Type of oil Oil quantity mark
Moebius 9010 NORMAL QUANTITY
Moebius 9030 SUFFICIENT QUANTITY
S-6
Remarks:
Date dial …Cal.VD33 only
*All parts code are subject to change without notice.
P-4
42 Setting lever 0383 368 0383 470
41 Train wheel setting lever 0391 368 0391 357
32 Fourth wheel and pinion 0241 178
Hour wheel 0271 407
P-2
0271 406
17 Small minute wheel 0888 014 0888 013
18
0902 015
0817 357
PARTS CATALOGUE
3H 3H White Black
SII Products
0157 1307 Small hour hand wheel 0157 006
0241 177
Intermediate date driving wheel
…Cal.VD33
Intermediate small hour hand wheel
…Cal.VD34
14 12 hours wheel 0902 016
5
Part code
Position of
crown
Position of
date frame
Color of
figure
Color of
background
0878 220 3H 3H Black White
0878 221
8 0817 368
No
Version-03
VD33&VD34
Page
Auxiliary train wheel bridge4
Parts code
0126 357
Parts form
Parts code
0126 368
VD33 VD34 Parts formParts name
The explanation here is only for the particular point of Cal.VD33&VD34
1.REMARKS ON INSTALLING THE BATTERY
(1) Battery
How to install the battery
Remove the hook of the switch springs battery clamp portion.
Insert the battery sideways, and have the hook of the switch springs battery clamp portion catch
the main plate.
Battery clamp position
Hook
Main plate
Hook
(2) After the battery is replaced with a new one or after the
Tweezers
battery is reinstalled following the repairing procedures,
Be sure to touch the short-circuit the AC terminal of circuit
block and the switch spring with conductive tweezers
to reset the circuit as illustrated at right.
(3) When the battery replaced with a new one, the time information stored in the built-in IC and the time
indicated by the dual time of 12 hour regulator and dual time of 60 minute regulator hands do not
correspond with each other.
Reset the dual time of 12 hour regulator and dual time of 60 minute regulator hands to "0" position
following the procedure below.
If the dual time of 12 hour regulator and dual time of 60 minute regulator hands should move improperly,
also follow the same procedure.
Note
Refer to page 8 for each adjustment method.
TECHNICAL GUIDE
Version-01
VD33&VD34
6
SII Products
2.To remove the winding stem
(1) set the winding stem to normal position.
(2) While pushing the indented portion of the arrow,
pull out the winding stem.
Push
3.How to attach hands
Place the movement directly on a flat metal plate or the like and press in the hands.
*install the hour , minute and second hands at the "12"o'clock position.
*Install the 24 hour indicator at the "24" position.
*Install the dual time of 12 hour regulator and dual time of 60 minute regulator hands at the "12" and "60"
position respectively.
[ Reference ] The power of press hands
Minute & Hour Hands
< 5kg
Second Hand < 5kg
24 hour indicator < 3kg
Dual time of 12 hour regulator hand < 3kg
Dual time of 60 minute regulator hand < 3kg
SII Products
7
TECHNICAL GUIDE
Version-01
VD33&VD34
Minute hand
Button A … -1 hour / push
Hour hand
(Difference in time correct, move Crown at normal position
together with dual time 60 minute
regulator hand) Button B … +1 hour / push
Second hand
Dual time of 60 minute regulator hand 24 hour hand
(Difference in time correct, move together (Indicates the time on a 24 hour basis)
with dual time 12 hour regulator hand)
Note
*Dual time of 60 minute regulator hand rotates one revolution every 15 minute.
There is no problem because this is typical function.
Before setting the time , check if the dual time of 12 hour regulator and dual time of 60 minute regulator
hands are in the "0"(12o'clock) position.
If either of the dual time of 12 hour regulator and dual time of 60 minute regulator hands are not in the
"0" position, reset them following the procedure below.
The battery setting and after battery change, please execute the "0" position adjustment.
1.Pull out the crown. 3.Press button A or B to reset the 4.Push the crown back to
VD33…second click dual time of 12 hour regulator and the normal position.
VD34…first click dual time of 60 minute regulator
hands to "0"position.
2.Keep the buttons "A"&"B" *By pressing button A the hands
pressed at the same time move counter clockwise.
more than 2 seconds, *By pressing button B the hands
and then release the buttons. move clockwise.
*Dual time of 60 minute regulator *Press and hold the button,
hand moves. Returned to where possible to fast-forward modification.
it was. *Dual time of 12 hour regulator hand are
linked to dual time of 60 minute regulator hand.
Note
Please repeat above 4 steps, as 0 position adjustment, if the dual time of 60 minute regulator hand
moves as follows;
Up to 1 minute to 14 minutes, one step/push, in 15 minutes, repeat the one rotation / push
OPERATION
Version-01
VD33&VD34
SII Products
8
DISPLAY AND CROWN / BUTTON OPERATION
Dual time of 12 hour regulator hand
ADJUSTING THE DUAL TIME OF 12 HOUR REGULATOR AND DUAL TIME OF 60 MINUTE REGULATOR HANDS POSITION
Dual time of 12 hour regulator hand adjustment
Dual time of 12 hour regulator hand adjustment
A
B
A
B
First position
VD33…Date setting
VD34…Time setting
Second position
VD33…Time setting
1.Pull out the crown when the second hand is at the
12 o'clock position.
[ Crown position ]
VD33…second click
VD34…first click
2.Turn the crown to set the hour and minute hands.
(Check that 24 hour hand is set correctly)
3.Push the crown back normal position in accordance with
a time signal.
Note
*The 24 hour hand moves correspondingly with the hour hand.
*The moment the date changes is midnight. when setting the hour hand, make sure that AM/PM
is correctly set by using the 24 hour hand as an AM/PM indicator.
*At the time of carrying, dual time of 60 minute regulator hand rotates one revolution every 15 minutes.
There is no problem because this is typical function.
Using the time different correction
When moving to a country or area which is in a different timezone , the current time in the local time
can be corrected.
1.Crown the normal position.
2.To adjust the time by pressing the button A or B.
*By pressing button A the hands move counter clockwise. -1hour / push
*By pressing button B the hands move clockwise. +1hour / push
1.Pull out the crown when the second hand is at the
12 o'clock position.
[ Crown position ]
VD33…second click
VD34…first click
2.To adjust the time by pressing the buttons A or B.
By pressing button A the hands move counter clockwise.
By pressing button B the hands move clockwise.
*Press and hold the button, possible to fast-forward modification.
3.Push the crown back in to the normal position.
Note
Every 15 minutes, dual time of 60 minute hand is one rotation/push.
OPERATION
Version-01
VD33&VD34
TIME SETTING
SII Products
9
TIME SETTING...DUAL TIME OF 12 HOUR REGULATOR AND DUAL TIME OF 60 MINUTE REGULATOR HANDS
A
B
*Before setting the date, be sure to set the time.
1.Pull out the crown to the first click.
2.Turn the crown to clockwise until the next date appears.
3.Push the crown back in to the normal position.
Note
*Do not set the date during any time between 9:00 P.M. and 1:00 A.M.
Otherwise, the date may not change properly. If it is necessary to set the date during that time period,
First change the time to any time outside it, set the date and then reset the correct time.
OPERATION
Version-01
VD33&VD34
DATE SETTING …Cal.VD33 only
SII Products
10
-
1
-
2
-
3
-
4
-
5
-
6
-
7
-
8
-
9
-
10
-
11
Time Module VD34 Technical Manual & Parts Catalogue
- Type
- Technical Manual & Parts Catalogue
- This manual is also suitable for
Ask a question and I''ll find the answer in the document
Finding information in a document is now easier with AI
Related papers
Other documents
-
Sekonda M BLACK DIAL DUAL TIME WATCH User manual
-
eta 2894-2 User manual
-
VESTEL DVD4250D Dvd Player
-
-
-
Seiko 5d88A Technical Manual
-
Samsung HLR5067W - 50" Rear Projection TV User manual
-
Haier HL26P2 User manual
-
-
Ronda xtratech Technical Instructions