Silvercrest KH 2610 User manual

■ NEGATIVE DIGITISER

FI

SE

Operating instructions

Käyttöohje

Bruksanvisning

KOMPERNASS GMBH ⋅ BURGSTRASSE 21 ⋅ D-44867 BOCHUM

www.kompernass.com

ID-Nr.: KH2610 08/2009-V3

Negative Digitiser

Negatiivien digitointilaite

Scanner för negativ

3A

GB

CV_KH2610_37970_LB3A.indd 1-4 26.10.2009 14:29:41 Uhr

Operating instructions .........................................................5

Käyttöohje ......................................................................... 33

Bruksanvisning ..................................................................61

KH 2610

FI

SE

2

3

4

6

5

7

GB

CV_KH2610_37970_LB3A.indd 5-8 26.10.2009 14:29:41 Uhr

5

KH 2610

GB

Index

Introduction . . . . . . . . . . . . . . 6

Preface . . . . . . . . . . . . . . . . 6

Information for these

operating instructions . . . . . 6

Copyright . . . . . . . . . . . . . . 7

Limited liability . . . . . . . . . . 7

Warnings . . . . . . . . . . . . . . 7

Proper use . . . . . . . . . . . . . 8

Safety . . . . . . . . . . . . . . . . . . . 9

Basic safety instructions . . . 9

Setting up and connecting to

the power supply . . . . . . . . . 10

Safety information . . . . . . 10

Package contents and

transport inspection . . . . . 11

Disposal of the packaging . . .11

Requirements for the

set-up location . . . . . . . . . 12

Connecting to a computer . . . . .12

Operating components

(see fold-out sides) . . . . . . . . 21

The ArcSoft PhotoImpression

6 programme . . . . . . . . . . 21

Handling and operation . . . 22

Inserting ﬁ lm strips . . . . . . 22

Inserting slides . . . . . . . . . 22

Starting the ArcSoft Photo-

Impression 6 programme . 23

Scanning with the

ArcSoft Photo-

Impression 6 programme . . . .23

After use . . . . . . . . . . . . . . 26

Cleaning . . . . . . . . . . . . . . . . 27

Safety information . . . . . . 27

Cleaning . . . . . . . . . . . . . 27

Troubleshooting . . . . . . . . . . 27

Safety information . . . . . . 28

Malfunction causes and

remedies . . . . . . . . . . . . . . 28

Storage/Disposal . . . . . . . . . 29

Storage . . . . . . . . . . . . . . . 29

Disposing of the device . . 29

Appendix . . . . . . . . . . . . . . . 30

Technical data . . . . . . . . . 30

Note regarding the EG

conformity declaration . . . 31

Warranty . . . . . . . . . . . . . 31

Service . . . . . . . . . . . . . . . 32

Importer . . . . . . . . . . . . . . 32

IB_KH2610_37970_LB3A.indb 5 26.10.2009 12:35:04 Uhr

Introduction

GB

6

KH 2610

Introduction

Preface

Dear customer,

by purchasing the negative digitiser KH 2610 you have decided on

a quality product from SilverCrest which, in terms of technology

and functionality, meets the most up-to-date development standards.

Read the information included here so that you can quickly familiarize

yourself with your device and thus make full use of its functions.

We wish you a great deal of enjoyable use.

Information for these operating instructions

These operating instructions are a component of the negative digitiser

KH 2610 (henceforth designated as the device) and supplies you

with important information for intended use, safety and connection as

well as operation of the device.

The operating instructions must be constantly kept available close to

the device. They are to be read and used by anyone assigned to the

operation and repairing of the device.

Keep these operating instructions and hand them over with the device

to any future owners.

IB_KH2610_37970_LB3A.indb 6 26.10.2009 12:35:05 Uhr

Introduction

7

KH 2610

GB

Copyright

This documentation is copyright protected.

Any copying and/or printing, including partial copying/printing, as

well as reproductions of the diagrams, even in an altered state is only

allowed with written permission from the manufacturer.

Limited liability

All technical information, data and information for connection and

operation, contained in these operating instructions correspond to the

latest at the time of printing and, to the best of our knowledge, take

into account our previous experience and know-how.

No claims can be derived from the details, illustrations and descriptions

in these instructions.

The manufacturer assumes no responsibility for damage caused by

failure to observe the instructions, improper use, inappropriate repairs,

making unauthorized changes or for using unapproved replacement

parts.

Warnings

In the current operation instructions the following warnings are used:

WARNING

A warning of this danger level signiﬁ es a possible

dangerous situation.

If the dangerous situation is not avoided it can lead to injuries.

The directives in this warning are there to avoid personal

►

injuries.

IB_KH2610_37970_LB3A.indb 7 26.10.2009 12:35:05 Uhr

Introduction

GB

8

KH 2610

IMPORTANT

A warning of this danger level signiﬁ es possible

property damage.

If the situation is not avoided it can lead to property damage.

The directives in this warning are there to avoid property

►

damage.

NOTICE

A notice signiﬁ es additional information that assists in the ►

handling of the device.

Proper use

This device is intended exclusively for the non-commercial use of scanning

and digitizing ﬁ lm negatives and slides.

This device is not intended for any other use or for uses beyond those

mentioned.

WARNING

Danger from unintended use!

Danger can come from the device if used for unintended purposes

and/or other types of use.

Use the device exclusively for intended purposes. ►

Observe the procedures described in these operating instruc- ►

tions.

Claims of any kind for damage resulting from unintended use will not

be excepted.

The operator alone bears liability.

IB_KH2610_37970_LB3A.indb 8 26.10.2009 12:35:05 Uhr

Safety

9

KH 2610

GB

Safety

In this chapter you receive important safety information regarding

handling of the device.

This device complies with the statutory safety regulations. Improper

use can lead to personal injury and property damage.

Basic Safety Instructions

For safe handling of the device observe the following safety information:

Before use check the device for visible external damage. Do not put

■

into operation a device that is damaged or has been dropped.

Damaged cables or connections should be replaced by authorized

■

qualiﬁ ed persons or by the customer service department.

Persons who, due to their physical, intellectual or motor abilities,

■

are incapable of operating the device safely may only use the

device under supervision or direction from a responsible person.

Only permit children to use the device under supervision.

■

Repairs should only be carried out by authorized specialist com- ■

panies or by the customer service department. Incorrect repairs

can result in signiﬁ cant dangers for the user. In addition warranty

claims become void.

IB_KH2610_37970_LB3A.indb 9 26.10.2009 12:35:05 Uhr

Setting up and connecting

GB

10

KH 2610

A repair to the device during the warranty period may only be ■

carried out by a cutomer service department authorized by the

manufacturer otherwise no additional warranty claims can be

considered for subsequent damages.

Defective components may only be replaced with original replace-

■

ment parts. Only by using original replacement parts can you

guarantee that the safety requirements are complied with.

Do not carry out any unauthorised recontructions or alterations to

■

the device.

Protect the device from moisture and liquid penetration.

■

Do not operate the device in the vicinity of open ﬂ ames. ■

Setting up and connecting

Safety instructions

WARNING

Personal injury and property damage can occur

during initial operation of the device!

Observe the following safety information to avoid danger:

Packaging material should not be used as a play thing.

►

There is a risk of suﬀ ocation!

IB_KH2610_37970_LB3A.indb 10 26.10.2009 12:35:05 Uhr

Setting up and connecting

11

KH 2610

GB

Package contents and transport inspection

The device is delivered with the following components as standard:

Scanner ●

Slide holder ●

Film negative holder ●

Programme and driver CD ●

Cleaning brush ●

Operating instructions ●

NOTICE

Check the contents to make sure everything is there and for ►

visible damage.

If the contents are not complete or are damaged due to defective

►

packaging or through transportation contact the service hotline

(see warranty card).

Disposal of the packaging

The packaging protects the device from transport damage. The pack-

aging materials are selected from the point of view of their environ-

mental friendliness and disposal technology and are therefore recy-

clable.

The recirculation of packaging into the material circuit saves

on raw material and reduces generated waste. Dispose of

packaging material that is no longer needed according to

the regionally established regulations.

NOTICE

If possible preserve the device's original packaging during ►

the warranty period so that in the case of a warranty claim

you can package the device properly for return.

IB_KH2610_37970_LB3A.indb 11 26.10.2009 12:35:05 Uhr

Setting up and connecting

GB

12

KH 2610

Requirements for the set-up location

For safe and faultless operation of the device the set-up location must

fulﬁ ll the following provisions:

The device must be placed on a ﬁ rm, ﬂ at and level surface.

■

Do not place the device in a hot, wet or very damp environment or ■

in the vicinity of ﬂ ammable materials.

Place the device so that it is not subjected to direct sunlight.

■

Connecting to a computer

System prerequisites

You will need a computer with a vacant USB port and with the



operating system Windows

®

XP, Windows

®

Vista or Windows

®

7

from the Microsoft

®

corporation.

Installation of the drivers and the

ArcSoft PhotoImpression 6 programme

NOTICE

In these operating instructions only the programme sections ►

are described that you will need for scanning your slides

and/or ﬁ lm negatives. You can ﬁ nd further information in the

programme's on-line help.

The illustrations and descriptions refer to the operating system ►

Microsoft® Windows® Vista. The illustration depictions can

diﬀ er, depending on the display settings, with other operating

systems.

IB_KH2610_37970_LB3A.indb 12 26.10.2009 12:35:06 Uhr

Setting up and connecting

13

KH 2610

GB

Insert the supplied programme and driver CD into your computer's 

CD drive.

The window "Automatic playback" will be displayed.

Click on the button "run autorun.exe". 

The installation begins and the start window is displayed.

NOTICE

If you have switched oﬀ the autostart function and the installation ►

process does not begin automatically you can start the in-

stallation process by double clicking on the ﬁ le "autorun.exe"

in the CD's main directory.

Click on the button "Scanner driver". 

Click on the button "Allow" in the Vista user account settings 

window.

IB_KH2610_37970_LB3A.indb 13 26.10.2009 12:35:06 Uhr

Setting up and connecting

GB

14

KH 2610

The driver installation is applied and the installation programme

conﬁ gured.

The welcome window of the installation programme is displayed.

Click on the button "Next >". 

The window "Ready to Install the Program" is displayed.

IB_KH2610_37970_LB3A.indb 14 26.10.2009 12:35:06 Uhr

Setting up and connecting

15

KH 2610

GB

Click on the button "Install" 

The driver will now be installed. The installation progress will be

displayed.

The display will show that the installation has been completed.

IB_KH2610_37970_LB3A.indb 15 26.10.2009 12:35:06 Uhr

Setting up and connecting

GB

16

KH 2610

Click on the button "Finish" to exit the installation wizard. 

The start window will be displayed again.

Click on the button "Arcsoft Software" to install the "ArcSoft Photo-



Impression 6“ programme.

Click on the button "Continue" in the Vista user account settings



window.

The window for language selection will be displayed.

Select the desired language and click on the button "OK". 

The installation wizard will be conﬁ gured.

The start window of the installation wizard will be displayed.

Click on the button "Continue >". 

The window "License agreement" will be displayed.

IB_KH2610_37970_LB3A.indb 16 26.10.2009 12:35:07 Uhr

Setting up and connecting

17

KH 2610

GB

Click on the button "Yes". 

The window for the selection of the installation directory will be

displayed.

Select the desired installation directory and click on the button 

"Continue >".

The window for the selection of the programme folders (Entry in

the Windows start menu) will be displayed.

IB_KH2610_37970_LB3A.indb 17 26.10.2009 12:35:07 Uhr

Setting up and connecting

GB

18

KH 2610

Select the desired programme folder and click on the button 

"Continue >".

The programme will be installed and the installation progress will

be displayed.

The window "Associated ﬁ le formats" will be displayed.

IB_KH2610_37970_LB3A.indb 18 26.10.2009 12:35:07 Uhr

Setting up and connecting

19

KH 2610

GB

Select the ﬁ le format that is to be associated with the programme 

and click on the button "Continue >".

The display will show that the installation has been completed.

Click on the button "Finish". 

The start window will be displayed again.

Click on the button "Exit Installation" to exit the installation programme.



Connection

Connect the USB cable



4

to a USB port on your computer.

When the device is connected for the ﬁ rst time the window "New

hardware found" will be shown.

IB_KH2610_37970_LB3A.indb 19 26.10.2009 12:35:09 Uhr

Setting up and connecting

GB

20

KH 2610

Click on the button "Search for and install driver software 

(Recommended).

Click on the button "Continue" in the Vista user account settings



window. All necessary drivers will be installed.

NOTICE

If you want to connect the device to another USB port the ►

window "Device software installation" will be displayed.

Click on the button "Completion of the software installation ►

(Recommended)".

IB_KH2610_37970_LB3A.indb 20 26.10.2009 12:35:09 Uhr

Operating components

21

KH 2610

GB

Operating components (see foldout sides)

LED PWR

2

COPY button.

3

Slot for ﬁ lm and/or slide holders.

4

USB connection cable.

5

Film holder.

6

Slide holder.

7

Cleaning brush

The ArcSoft PhotoImpression 6 programme

1

5

3

2

4

IB_KH2610_37970_LB3A.indb 21 26.10.2009 12:35:09 Uhr

Handling and operation

GB

22

KH 2610

1 Menu bar

2 Toolbar

3 File extent

NOTICE

In the ﬁ le extent only subdirectory and programme processed ►

ﬁ les will be displayed.

4 Status bar

5 File directory tree

Handling and operation

In this chapter you receive important information for the handling and

operation of the device.

Inserting ﬁ lm strips

Release the fastener on the front of the ﬁ lm holder 

5

and open

the holder.

Insert the ﬁ lm strip into the holder correctly orientated.



Close the holder making sure that the cover locks into place. 

Inserting slides

Release the fastener on the front of the slide holder 

6

and open

the holder.

Insert a maximum of 3 framed slides, correctly orientated, into



the holder.

Close the holder making sure that the cover locks into place.



IB_KH2610_37970_LB3A.indb 22 26.10.2009 12:35:11 Uhr

Page is loading ...

Silvercrest KH 2610 User manual

This manual is also suitable for

Silvercrest KH 2610 User manual

in other languages

Related papers

Other documents