Enttec RGB Black Pixel Tape 12V 5m Installation guide

Brand
Enttec
Model
RGB Black Pixel Tape 12V 5m
Type
Installation guide

This manual is also suitable for

Enttec RGB Black Pixel Tape 12V 5m is a high-quality LED strip designed for professional lighting applications. With its 60 LEDs per meter and a maximum length of 7 meters for single injection and 11.3 meters for dual injection, it provides ample brightness and coverage for various lighting scenarios. The pixel tape offers precise color control, allowing you to create vibrant and dynamic lighting effects. Its durable construction and strong adhesive backing ensure long-lasting performance, making it suitable for both indoor and outdoor use.

Enttec RGB Black Pixel Tape 12V 5m is a high-quality LED strip designed for professional lighting applications. With its 60 LEDs per meter and a maximum length of 7 meters for single injection and 11.3 meters for dual injection, it provides ample brightness and coverage for various lighting scenarios. The pixel tape offers precise color control, allowing you to create vibrant and dynamic lighting effects. Its durable construction and strong adhesive backing ensure long-lasting performance, making it suitable for both indoor and outdoor use.

PAGE 1/1
ENTTEC RESERVES THE RIGHT TO MAKE CHANGES TO THIS
PRODUCT AND RELATED DOCUMENTS AT ANY TIME WITHOUT
NOTICE, THE MOST RECENT DOCUMENTATION IS AVAILABLE AT ENTTEC.COM
8P (12 VOLT) PIXEL STRIP
INSTALLATION GUIDE
ID: 5283038
IMPORTANT: FOLLOW THE INSTRUCTIONS AND RECOMMENDATIONS BELOW,
OR YOU MAY EXPERIENCE POOR PRODUCT PERFORMANCE OR EVEN FAILURE.
! !
MAXIMUM RUN LENGTH
COLOUR AND LUMEN OUTPUT WILL BE AFFECTED IF
MAXIMUM LENGTH IS EXCEEDED. TEST CONDUCTED AT
MAXIMUM BRIGHTNESS USING 12 VOLT DRIVER.
SINGLE
DUAL
CUTTING
ONLY CUT ALONG THE LINES MARKED ON THE STRIP
GND
BI
DI
12V
GND
BO
DO
12V
GND
BI
DI
12V
GND
BO
DO
12V
GND
BI
DI
12V
GND
BO
DO
12V
GND
BI
DI
12V
GND
BO
DO
12V
ADHESIVE APPLICATION
• THE PIXEL STRIP WILL NOT ADHERE TO TEXTURED OR
LOW SURFACE ENERGY MATERIALS.
• THE BEST SURFACE FOR LONG LASTING ADHESION IS
CLEAN RAW METAL.
• CLEAN SUBSTRATE WITH ALCOHOL AND A CLEAN CLOTH.
• PEEL OFF PROTECTIVE BACKING TO REVEAL ADHESIVE.
• APPLY PRESSURE WHEN ADHESIVE FIXING TO SUBSTRATE.
THERMAL MANAGEMENT
• THESE PIXEL STRIP PRODUCE HEAT, THERMAL MANAGEMENT MUST
BE CONSIDERED.
• THE MORE LEDS PER METRE THE MORE HEAT.
• ENTTEC RECOMMENDS USING AN ALUMINIUM PROFILE TO
MANAGE HEAT.
• EACH APPLICATION IS DIFFERENT. ENTTEC RECOMMENDS TESTING
A SECTION OF STRIP IN ITS FINISHED ENVIRONMENT TO ENSURE
THE THERMAL MANAGEMENT IS SATISFACTORY.
WIRING SCHEMATIC
• SELECT THE MOST SUITABLE OPTION FROM BELOW. SOLDER OR CRIMP IS RECOMMENDED TO COMBINE MULTIPLE WIRES.
• IF WIRE COLOURS VARY AND YOU ARE UNSURE, PLEASE CONTACT ENTTEC OR YOUR SUPPLIER FOR FURTHER ADVICE.
• THE YELLOW WIRE WILL ALWAYS BE DATA.
SINGLE POWER INJECTION
GND
12V
DATA
BACKUP
DATA
DUAL POWER INJECTION
GND
12V
DATA
BACKUP
DATA
PSU
VOLTAGE: 12
WATTS: (STRIP LENGTH IN
METRES) x (WATTS PER METRE)
GND
12V (1)
BACKUP
DATA
12V (2)GND
DO NOT CONNECT 12V(1) TO 12V(2)
DATA
DATA JOIN WITH MULTIPLE SINGLE POWER INJECTIONS
GND
BI
DI
12V
GND
BO
DO
12V
12V
GND
DATA JOIN
DO:
DI:
(DATA OUT)
(DATA IN)
BLACK
YELLOW
RED
GREEN
VOLTAGE DROP TESTING
USE MULTIMETER TO TEST FOR VOLTAGE DROP TEST WHERE POWER IS INJECTED. IF PROBLEMS OCCUR ALSO METER THE END OF THE STRIP.
POWER INJECTION
12
SET LED COLOUR TO FULL WHITE
PRIOR TO TESTING
END
11.6 - 12.2
11.6 12.3
LEDS PER
METRE
THIS DOCUMENT AND DESIGN IS PROPERTY OF ENTTEC.
REPRODUCTION OR USE OF ANY MATERIAL CONTAINED
WITHIN MUST BE APPROVED IN WRITING BY ENTTEC.
WHITE MAXIMUM LENGTH
(METRE)
POWER
INJECTION
COLOUR CONSISTENCY
TO ACHIEVE OPTIMAL COLOUR CONSISTENCY ACROSS MULTIPLE PIXEL STRIPS,
WE RECOMMEND USING THOSE FROM THE SAME MANUFACTURING BATCH
TOGETHER WHEREVER POSSIBLE. PLEASE CHECK YOUR BATCH NUMBERS -
THESE CAN BE FOUND ON THE PRODUCT LABEL.
60
60
Note: Maximum length of pixel strip run is limited
by maximum universes of data (4 universes)
7
GND
BI
DI
12V
GND
BO
DO
12V
GND
BI
DI
12V
GND
BO
DO
12V
11.3
  • Page 1 1

Enttec RGB Black Pixel Tape 12V 5m Installation guide

Brand
Enttec
Model
RGB Black Pixel Tape 12V 5m
Type
Installation guide
This manual is also suitable for

Enttec RGB Black Pixel Tape 12V 5m is a high-quality LED strip designed for professional lighting applications. With its 60 LEDs per meter and a maximum length of 7 meters for single injection and 11.3 meters for dual injection, it provides ample brightness and coverage for various lighting scenarios. The pixel tape offers precise color control, allowing you to create vibrant and dynamic lighting effects. Its durable construction and strong adhesive backing ensure long-lasting performance, making it suitable for both indoor and outdoor use.

Download PDF
report

Ask a question and I''ll find the answer in the document

Finding information in a document is now easier with AI

Related papers

Other documents