PA
GE 1/1
ENTTEC RESERVES THE RIGHT TO MAKE CHANGES TO THIS
PRODUCT AND RELATED DOCUMENTS AT ANY TIME WITHOUT
NOTICE, THE MOST RECENT DOCUMENTATION IS AVAILABLE AT ENTTEC.COM
IMPORTANT: FOLLOW THE INSTRUCTIONS AND RECOMMENDATIONS BELOW,
OR YOU MAY EXPERIENCE POOR PRODUCT PERFORMANCE OR EVEN FAILURE.
!!
MAXIMUM RUN LENGTH
CO
LOUR AND LUMEN OUTPUT WILL BE AFFECTED IF
MAXIMUM LENGTH IS EX
CEEDED. TEST CONDUCTED AT
MAXIMUM BRIGHTNESS USING 12
VOLT DRIVER.
CUTTING
ONLY CUT ALONG THE LINES MARKED ON THE STRIP
GND
DI
12V
GND
DO
12V
GND
DI
12V
GND
DO
12V
GND
DI
12V
GND
DO
12V
GND
DI
12V
GND
DO
12V
GND
DI
12V
GND
DO
12V
ADHESIVE APPLICA
TION
• THE STRIP WILL NO
T ADHERE TO TEXTURED OR
LOW SURF
ACE ENERGY MATERIALS.
• THE BEST SURF
ACE FOR LONG LASTING ADHESION IS
CLEAN RA
W METAL.
• CLEAN SUBSTRA
TE WITH ALCOHOL AND A CLEAN CLOTH.
• PEEL OFF PRO
TECTIVE BACKING TO REVEAL ADHESIVE.
• APPL
Y PRESSURE WHEN ADHESIVE FIXING TO SUBSTRATE.
THERMAL MANAGEMENT
• THESE STRIPS PRODUCE HEAT. THERMAL MANAGEMENT MUST
BE CONSIDERED.
• THE MORE LEDS PER METRE, THE MORE HEAT.
• ENTTEC RECOMMENDS USING AN ALUMINIUM PROFILE TO
MANAGE HEAT.
• EACH APPLICATION IS DIFFERENT. ENTTEC RECOMMENDS TESTING
A SECTION OF STRIP IN ITS FINISHED ENVIRONMENT TO ENSURE
THE THERMAL MANAGEMENT IS SATISFACTORY.
WIRING SCHEMA
TIC
• SELECT THE MOST SUIT
ABLE OPTION FROM BELOW. SOLDER OR CRIMP IS RECOMMENDED TO COMBINE MULTIPLE WIRES.
• IF WIRE
COLOURS VARY AND YOU ARE UNSURE, PLEASE CONTACT ENTTEC OR YOUR SUPPLIER FOR FURTHER ADVICE.
• THE MIDDLE WIRE WILL A
LWAYS BE DATA.
SINGLE POWER INJECTION
GND
12V
DATA
DUAL POWER INJECTION
GND
12V
DATA
PSU
VOLTAGE: 12
WATTS: (STRIP LENGTH IN
METRES) x (WATTS PER METRE)
GND
12V (1)
DATA
12V (2)GND
STRIP ONE STRIP TWO
DO NOT CONNECT 12V(1) TO 12V(2)
DATA JOIN WITH MULTIPLE SINGLE POWER INJECTIONS
GND
DI
12V
GND
DO
12V
GND
DI
12V
GND
DO
12V
12V
GND
DATA JOIN
DO:
DI:
(DATA OUT)
(DATA IN)
BLACK
GREEN
RED
VO
LTAGE DROP TESTING
USE MUL
TIMETER TO TEST FOR VOLTAGE DROP TEST WHERE POWER IS INJECTED. IF PROBLEMS OCCUR ALSO METER THE END OF THE STRIP.
PUSH PROBES
THROUGH
PROTECTIVE
SILICONE TO
MAKE CONTACT
THIS DOCUMENT AND DESIGN IS PROPERTY OF ENTTEC.
REPRODUCTION OR USE OF ANY MATERIAL CONTAINED
WITHIN MUST BE APPROVED IN WRITING BY ENTTEC.
COLOUR CONSISTENCY
TO ACHIEVE OPTIMAL COLOUR CONSISTENCY ACROSS MULTIPLE STRIPS,
WE RECOMMEND USING THOSE FROM THE SAME MANUFACTURING BATCH
TOGETHER WHEREVER POSSIBLE. PLEASE CHECK YOUR BATCH NUMBERS -
THESE CAN BE FOUND ON THE PRODUCT LABEL.
8PXW60-F-12-B (12 VOLT) PIXEL STRIP
INST
ALLATION GUIDE
ID: 5628054
60
60
7m
15m
SINGLE
POWER
INJECTION
DUAL
POWER
INJECTION
LEDS PER METRE WHITE
RED,GREEN,BLUE
MAXIMUM LENGTH
12.8m
15m
POWER INJECTION
12
SET LED COLOUR TO FULL WHITE
PRIOR TO TESTING
END
11.7 - 12.2
12.311.6
ALL ON
5m
10m
-
1
Ask a question and I''ll find the answer in the document
Finding information in a document is now easier with AI
Related papers
-
Enttec RGB Black Pixel Tape 12V 5m Installation guide
-
Enttec RGB Black Pixel Tape 5V 5m User manual
-
Enttec Pixie Driver User manual
-
Enttec Pixel Triton User manual
-
Enttec Pixel Triton User manual
-
Enttec S-PLAY Light show recorder User manual
-
Enttec S-Play 51301 User manual
-
Enttec S-Play User manual
-
Enttec CV DRIVER MK2 User manual
-
Enttec MK2 User manual
