Kichler Lighting 44011MIZ User manual

Brand
Kichler Lighting
Model
44011MIZ
Type
User manual
12) Make wire connections (connectors not provided). Reference
chart below for correct connections and wire accordingly.
13) Push fixture to ceiling, carefully passing mounting screws
through holes in canopy.
14) Thread knurl knobs onto mounting screws. Tighten knurl
knobs to secure fixture to ceiling.
15) Raise glass up to fixture. Pass hole in glass over socket.
16) Fit larger washer inside glass. Pass hole in washer over socket.
17) Thread socket ring onto socket. Tighten socket ring to hold
glass in place. (DO NOT over tighten.)
18) Insert recommended bulb. CAUTION: DO NOT touch bulb
with bare hands. If this happens, clean bulb with denatured
alcohol and a lint free cloth.
19) Carefully thread glass sleeve onto socket. (DO NOT over
tighten.)
Connect Black or
Red Supply Wire to:
Connect
White Supply Wire to:
Black White
*Parallel cord (round & smooth) *Parallel cord (square & ridged)
Clear, Brown, Gold or Black
without tracer
Clear, Brown, Gold or Black
with tracer
Insulated wire (other than green)
with copper conductor
Insulated wire (other than green)
with silver conductor
*Note: When parallel wires (SPT I & SPT II)
are used. The neutral wire is square shaped
or ridged and the other wire will be round in
shape or smooth (see illus.)
Neutral Wire
IMPORTANT SAFETY INSTRUCTIONS
LIGHTED BULB IS HOT!
WARNING: To reduce the risk of FIRE or INJURY TO PERSON:
• Turnoffandallowtocoolbeforereplacingbulb.
• BulbgetsHOTQUICKLY!Contactswitchonlywhenturningoff.
• DONOTremaininlightifskinfeelswarm.(Lightisintense,
may cause “sunburn”)
• DONOTlookdirectlyatlightedbulb.
• Keepmaterialsawayfrombulbthatmayburn.
• UseONLYwithwattagespeciedorlower.
• DONOTtouchbulbatanytime,useasoftcloth.Oilfromskin
may damage bulb.
• DONOToperatexturewithmissingordamagedglass.
1) Pass wire through stem and screw stem to coupling on top
of fixture body. NOTE: Thread locking compound must be
applied to all stem threads as noted with symbol (3) to prevent
accidental rotation of fixture during cleaning, relamping, etc.
2) Pass wire through remaining stems and screw stems
together.
3) Pass fixture wire through swivel. Thread swivel onto end of
last stem.
4) Pass fixture wire through small threaded pipe. Screw end of
small threaded pipe into end of swivel.
5) Passxturewirethroughholeincanopy.Lowercanopy
down and pass hole in canopy over end of threaded pipe on
swivel.
6) Pass fixture wire through hole in lockwasher. Thread
lockwasher onto end of threaded pipe protruding from
inside canopy.
7) Pass fixture wire through hole in hexnut. Thread hexnut onto
end of threaded pipe.
8) TURN OFF POWER.
IMPORTANT:Beforeyoustart,NEVERattemptanywork
without shutting off the electricity until the work is done.
a) Go to the main fuse, or circuit breaker, box in your
home. Place the main power switch in the “OFF”
position.
b) Unscrew the fuse(s), or switch “OFF” the circuit breaker
switch(s), that control the power to the fixture or room
that you are working on.
c) Place the wall switch in the “OFF” position. If the fixture
to be replaced has a switch or pull chain, place those in
the “OFF” position.
9) Find the appropriate threaded holes on mounting strap.
Assemble mounting screws into threaded holes.
10) Attach mounting strap to outlet box. (Screws not provided).
Mounting strap can be adjusted to suit position of fixture.
11)Groundinginstructions:(SeeIllus.AorB).
A) On fixtures where mounting strap is provided with a
hole and two raised dimples. Wrap ground wire from
outlet box around green ground screw, and thread into
hole.
B) Onxtureswhereacuppedwasherisprovided.Attach
ground wire from outlet box under cupped washer and
green ground screw, and thread into mounting strap.
If fixture is provided with ground wire. Connect fixture
ground wire to outlet box ground wire with wire connector
(not provided.) after following the above steps. Never
connect ground wire to black or white power supply wires.
Date Issued: 3/28/14 IS-44011-US
GREEN GROUND
SCREW
CUPPED
WASHER
A
B
OUTLET BOX
GROUND
FIXTURE
GROUND
DIMPLES
WIRE CONNECTOR
(NOT PROVIDED)
OUTLET BOX
GROUND
GREEN GROUND
SCREW
FIXTURE
GROUND
SEE OTHER SIDE FOR SPANISH TRANSLATIONS.
VEA EL OTRO LADO DE TRADUCCIONES AL ESPAÑOL.
We’re here to help 866-558-5706
Hrs: M-F 9am to 5pm EST
MOUNTING STRAP
ABRAZADERADEMONTAJE
CANOPY
ESCUDETE
FIXTUREBODY
CUERPODELARTEFACTO
KNURLKNOB
PERILLAESTRADA
3
STEM
VASTAGO
GLASS
VIDRIO
BULB
BOMBILLA
GLASSSLEEVE
CAMISADEVIDRIO
SOCKETRING
ANILLODELCASQULLO
LOCKWASHER
ARANDELADE
SEGURIDAD
HEXNUT
TUERCAHEXAGONAL
LARGEWASHER
ARANDELAMÁSGRANDE
SWIVEL
UNIÓN GIRATORIA
SMALLTHREADEDPIPE
PEQUEÑOTUBOROSCADO
3
3
Page is loading ...
IMPORTANT SAFETY INSTRUCTIONS
LIGHTED BULB IS HOT!
WARNING: To reduce the risk of FIRE or INJURY TO PERSON:
• Turnoffandallowtocoolbeforereplacingbulb.
• BulbgetsHOTQUICKLY!Contactswitchonlywhenturningoff.
• DONOTremaininlightifskinfeelswarm.(Lightisintense,
maycause“sunburn”)
• DONOTlookdirectlyatlightedbulb.
• Keepmaterialsawayfrombulbthatmayburn.
• UseONLYwithwattagespeciedorlower.
• DONOTtouchbulbatanytime,useasoftcloth.Oilfromskin
maydamagebulb.
• DONOToperatexturewithmissingordamagedglass.
1) Passwirethroughstemandscrewstemtocouplingontop
ofxturebody.NOTE:Threadlockingcompoundmustbe
appliedtoallstemthreadsasnotedwithsymbol(3)toprevent
accidentalrotationofxtureduringcleaning,relamping,etc.
2) Passwirethroughremainingstemsandscrewstems
together.
3) Passxturewirethroughswivel.Threadswivelontoendof
laststem.
4) Passxturewirethroughsmallthreadedpipe.Screwendof
smallthreadedpipeintoendofswivel.
5) Passxturewirethroughholeincanopy.Lowercanopy
downandpassholeincanopyoverendofthreadedpipeon
swivel.
6) Passxturewirethroughholeinlockwasher.Thread
lockwasherontoendofthreadedpipeprotrudingfrom
insidecanopy.
7) Passxturewirethroughholeinhexnut.Threadhexnutonto
endofthreadedpipe.
8) TURN OFF POWER.
IMPORTANT:Beforeyoustart,NEVERattemptanywork
withoutshuttingofftheelectricityuntiltheworkisdone.
a) Gotothemainfuse,orcircuitbreaker,boxinyour
home.Placethemainpowerswitchinthe“OFF”
position.
b) Unscrewthefuse(s),orswitch“OFF”thecircuitbreaker
switch(s),thatcontrolthepowertothextureorroom
thatyouareworkingon.
c) Placethewallswitchinthe“OFF”position.Ifthexture
tobereplacedhasaswitchorpullchain,placethosein
the“OFF”position.
9) Findtheappropriatethreadedholesonmountingstrap.
Assemblemountingscrewsintothreadedholes.
10)Attachmountingstraptooutletbox.(Screwsnotprovided).
Mountingstrapcanbeadjustedtosuitpositionofxture.
11)Makewireconnections(connectorsnotprovided.)Reference
chartbelowforcorrectconnectionsandwireaccordingly.
12) Pushxturetoceiling,carefullypassingmountingscrews
throughholesincanopy.
13) Threadknurlknobsontomountingscrews.Tightenknurl
knobstosecurexturetoceiling.
14) Raiseglassuptoxture.Passholeinglassoversocket.
15) Fitlargerwasherinsideglass.Passholeinwasheroversocket.
16) Threadsocketringontosocket.Tightensocketringtohold
glassinplace.(DONOTovertighten.)
17) Insertrecommendedbulb.CAUTION: DONOTtouchbulb
withbarehands.Ifthishappens,cleanbulbwithdenatured
alcoholandalintfreecloth.
18) Carefullythreadglasssleeveontosocket.(DONOTover
tighten.)
Connect Black or
Red Supply Wire to:
Connect
White Supply Wire to:
Black White
*Parallel cord (round & smooth)
*Parallel cord (square & ridged)
Clear, Brown, Gold or Black
without tracer
Clear, Brown, Gold or Black
with tracer
Insulated wire (other than green)
with copper conductor
Insulated wire (other than green)
with silver conductor
*Note: When parallel wires (SPT I & SPT II)
are used. The neutral wire is square shaped
or ridged and the other wire will be round in
shape or smooth (see illus.)
Neutral Wire
DateIssued:3/28/14 IS-44011-CB
INSTRUCTIONS
For Assembling and Installing Fixtures in Canada
Pour L’assemblage et L’installation Au Canada
We’re here to help 866-558-5706
Hrs: M-F 9am to 5pm EST
SEE OTHER SIDE FOR CANADIAN FRENCH TRANS-
LATIONS.
VOIR L’AUTRE CÔTÉ POUR LES CANADIENS TRA-
DUCTIONS EN FRANÇAIS.
MOUNTINGSTRAP
PATTEDEFIXATION
CANOPY
CACHE
KNURLKNOB
BOUTONMOLETÉ
STEM
TIGE
FIXTUREBODY
LUMINAIRE
4
GLASS
VERRE
BULB
L’AMPOULE
GLASSSLEEVE
MANCHONDEVERRE
SOCKETRING
ANNEAUDELADOUILLE
3
HEXNUT
ECROUHEXAGONAL
LOCKWASHER
RONDELLEDE
BLOCAGE
SMALLTHREADEDPIPE
PETITTUBEFILETÉ
LARGEWASHER
GRANDERONDELLE
SWIVEL
PIVOT
3
Page is loading ...
  • Page 1 1
  • Page 2 2
  • Page 3 3
  • Page 4 4

Kichler Lighting 44011MIZ User manual

Brand
Kichler Lighting
Model
44011MIZ
Type
User manual
Download PDF
report

Ask a question and I''ll find the answer in the document

Finding information in a document is now easier with AI

in other languages

Related papers

Other documents