Livex Lighting 65538-35 Installation guide

Type
Installation guide

This manual is also suitable for

Livex Lighting 65538-35 is a lighting fixture that can be used to replace an old fixture. It features a classic design with a glass shade and requires three light bulbs to operate. The fixture is easy to install and comes with all the necessary hardware, including mounting screws, a mounting plate, and ball nuts. It is important to turn off the power at the fuse or circuit breaker before installing the fixture. The fixture should be mounted to a junction box (not included) using the provided mounting screws.

Livex Lighting 65538-35 is a lighting fixture that can be used to replace an old fixture. It features a classic design with a glass shade and requires three light bulbs to operate. The fixture is easy to install and comes with all the necessary hardware, including mounting screws, a mounting plate, and ball nuts. It is important to turn off the power at the fuse or circuit breaker before installing the fixture. The fixture should be mounted to a junction box (not included) using the provided mounting screws.

ASSEMBLING & INSTALLATION INSTRUCTIONS
The drawing shown may not exactly match the product enclosed.
However, the installation instructions do apply to this product.
65536 65537 65538
WARNING! SHUT POWER OFF AT FUSE OR CIRCUIT BREAKER.
ATTENTION! COUPER LE COURANT AU FUSIBLE OU UN DISJONCTEUR.
ASSEMBLING THE FIXTURE (Fig.1)
1. Shut off the power at the fuse box or circuit breaker box. Remove the old
fixture from ceiling, including the mounting plate.
2. Carefully unpack your new fixture and lay out all the parts on a clear area.
Take care not to lose any small parts necessary for installation.
3. Thread the two mounting screws about 1/4”into the pre-drilled holes in the
mounting plate spaced the same distance apart as the holes in the pan
(A).
4. Attach the mounting plate to the Junction Box using the two screws from
the Junction Box as shown. The side of the mounting plate marked "GND"
must face out.
The junction box is not included.
5. Hold the pan (A) towards the mounting plate and connect the electrical
wires as follows (See Fig.2). Connect the black wire from the fixture to the
black house (hot) wire; connect the white wire from the fixture to the white
house (neutral) wire. Make sure all wire nuts are secured. You may wrap
the connections with electrical tape. If your Junction box has a ground
wire (green or bare copper) connects fixture’s ground wire to it. Otherwise
attach the bare copper fixture wire to the green ground screw on the
mounting plate. Tuck the wire connections neatly into the ceiling junction
box as you are holding the fixture assembly toward the ceiling.
6. Finish mounting the pan (A) by placing it over both mounting screws so
that the screws protrude from the holes in the bottom of the pan (A), lock it
securely with the ball nut(C).
7. Install the light bulbs(not included) in accordance with the fixture’s
specifications.
DO NOT EXCEED THE MAXIMUM WATTAGE
RATING!
8. Attach the glass shade(D) to the pan(A), then tighten it with the
screws(B).
Your installation is now complete. Return power to the
j
unction box and test the fixture.
Mountingplate
Mountingscrew
Fixture
JunctionBox
B
D
A
(Notincluded)
Wire
Wire
Ground
C
FIXTURE
WIRES
Black or
Smooth
HOUSE
WIRES
Black(Hot)
FIXTURE
WIRES
White or
Ribbed
FIXTURE
WIRES
Bare
Copper
(Ground)
HOUSE
WIRES
White
(Neutral)
HOUSE
WIRES
Green or Bare
Copper(Ground)
Thank you for purchasing a LIVEX product.
Need assistance with parts or assembly? Please call customer service at: 800-761-8056
Or visit us online at: WWW.LIVEXLIGHTING.COM
©COYRIGHT ALL RIGHTS RESERVED.LIVEX LIGHTING,INC. DOC20151265536
FIG.2
FIG.1
  • Page 1 1

Livex Lighting 65538-35 Installation guide

Type
Installation guide
This manual is also suitable for

Livex Lighting 65538-35 is a lighting fixture that can be used to replace an old fixture. It features a classic design with a glass shade and requires three light bulbs to operate. The fixture is easy to install and comes with all the necessary hardware, including mounting screws, a mounting plate, and ball nuts. It is important to turn off the power at the fuse or circuit breaker before installing the fixture. The fixture should be mounted to a junction box (not included) using the provided mounting screws.

Ask a question and I''ll find the answer in the document

Finding information in a document is now easier with AI