Charlotte Pipe CTS 12010 0500 User manual

TECHNICAL MANUAL

Plastics

TECHNICAL AND INSTALLATION MANUAL

TM-PL

ABS DWV

PVC DWV

RePVC® DWV Pipe with Recycled Content

PVC Sewer & Pressure Pipe

PVC Schedule 40 & 80

FlowGuard Gold® CTS CPVC

ReUze® CTS CPVC

Corzan® Schedule 80 CPVC

(Updated March 28, 2013)

2

Plastics Technical Manual

INTRODUCTION

Charlotte Pipe

®

has been relentless in our commitment

to quality and service for more than a century. Through

the years we have broadened and enhanced our product

lines to better serve our customers. As the leading full-line

manufacturer of PVC, CPVC, and ABS piping systems

for drainage and pressure applications, we welcome

the opportunity to be the one-stop source for all your

thermoplastic piping systems. Charlotte

®

is the only

company that manufactures pipe and ﬁttings to exacting

TrueFit tolerances. Our systems are designed to ﬁt together

precisely for easier installation, fewer callbacks and a

lifetime of trouble-free service - the major beneﬁts of a

Charlotte Pipe TrueFit

®

system.

Monroe, North Carolina

Cameron, Texas

Muncy, Pennsylvania

Wildwood, Florida

Manufacturing

Facilities

• Monroe,NorthCarolina

• Muncy,Pennsylvania

• Cameron,Texas

• Wildwood,Florida

• Huntsville,Alabama

• CedarCity,Utah

CharlottePipe,Charlotte,CharlottePipeTrueFit,RePVC,ReUze,and“Youcan’tbeatthesystem”

are registered trademarks of Charlotte Pipe and Foundry Company.

Huntsville, Alabama Cedar City, Utah

3

TABLE OF CONTENTS

GENERAL INFORMATION Page

Introduction ...................................................................................................................... 2

Understanding Safety-Alert Messages .............................................................................. 5

Major Advantages of ABS, PVC and CPVC Pipe .............................................................. 6

Handling and Storage of ABS, PVC and CPVC Pipe ......................................................... 7

Physical Properties of ABS and PVC Materials ................................................................ 8

ABS and PVC Standards ................................................................................................... 8

Physical Properties of FlowGuard Gold

®

, ReUze

®

and Corzan

®

CPVC Materials .............. 9

CPVC Standards ................................................................................................................ 9

Product Speciﬁcations ............................................................................................... 10-21

  ABSCellularCore(FoamCore)PipeandABSDWVFittingSystem ............................ 10

  PVCSchedule40SolidWallPipeandPVCDWVFittingSystem ................................. 11

  PVCCellularCore(FoamCore)PipeandPVCDWVFittingSystem ............................ 12

RePVC

®

-PVCSchedule40PipewithRecycledContentandPVCDWV

Fitting System ..................................................................................................... 13

PVC Schedule 40 Pressure Pipe and Fitting System ...................................................... 14

PVC SDR Pressure Pipe and Fitting System ................................................................. 15

PVC Schedule 80 Pressure Pipe and Fitting System ...................................................... 16

FlowGuard Gold CPVC CTS Pipe and Fitting System .................................................... 17

  ReUze

®

CPVC CTS Pipe and Fitting System ................................................................. 18

PVC SDR 35 Gravity Sewer Pipe ................................................................................. 19

PVC D 2729 Sewer and Drain Pipe .............................................................................. 20

Product Certiﬁcation ...................................................................................................... 21

PRODUCT DATA

Pipe Reference Guide ...................................................................................................... 22

Product Data (Dimensions, Weight and Pressure Ratings) ........................................ 23-39

Socket Dimensions for Belled-End Pipe .......................................................................... 34

DESIGN AND ENGINEERING DATA

Pressure/Temperature Relationship ............................................................................ 40-41

  MaximumOperatingTemperaturesforVariousPipingSystems ..................................... 40

Temperature De-Rating for PVC and CPVC................................................................... 40

  MaximumOperatingTemperaturesforCTSCPVCSDR11PipingSystems ................... 41

Low Temperature Recommendations ............................................................................. 41

Fluid Flow Properties ................................................................................................. 42-51

Gravity Flow and Fluid Flow Rate ............................................................................... 42

Pressure Flow Rate ..................................................................................................... 43

  WaterVelocities ......................................................................................................... 43

Friction Loss Through Fittings ..................................................................................... 43

  WaterHammer ...................................................................................................... 44-45

Entrapped Air ............................................................................................................. 46

  Weathering/UVExposure/HeatBuild-Up .................................................................. 46

Friction Loss and Flow Velocity Table ..................................................................... 47-51

Support Spacing for ABS, PVC and CPVC Pipe ........................................................ 52-53

Typical Pipe Hangers, Clamps, and Supports .................................................................. 53

Expansion and Contraction of Iron Pipe Size ABS, PVC and CPVC .......................... 54-56

  ThermalExpansioninDWVSystems............................................................................ 55

  ThermalExpansioninUndergroundSystems ................................................................ 55

Expansion and Contraction of CTS CPVC ..................................................................... 56

Permissible Bending Deﬂections for FlowGuard Gold

®

Pipe ........................................... 57

Flame Spread and Smoke Development Rating for ABS, PVC and CPVC ...................... 58

Chemical Resistance Chart of ABS, PVC, and CPVC ................................................ 59-79

Helpful Reference Standards ..................................................................................... 80-83

Conversion Charts ...................................................................................................... 84-85

ReUzeandRePVCareregisteredtrademarksofCharlottePipeandFoundryCompany.

CorzanandFlowGuardGoldareregisteredtrademarksofLubrizolCorp.

4

Plastics Technical Manual

INSTALLATION

Installation Procedures for ABS, PVC and CPVC Piping Systems ............................ 86-94

  FlowGuardGoldandReUze

®

CTS CPVC Pipe and Fitting Systems ........................... 86-88

  1/2”-4”ABS,PVCandCPVCPipeandFittingSystems .......................................... 88-90

  6”andLargerABS,PVCandCPVCPipeandFittingSystems................................. 90-93

Solvent Cements .......................................................................................................... 94

Applicator Types .......................................................................................................... 94

Joint Curing .................................................................................................................... 95

Flanges ............................................................................................................................ 96

Threaded Joints and Threading of PVC and CPVC Pipe .......................................... 97-100

Taper Thread Dimensions .......................................................................................... 100

  ImportantInformationforFittingswithPlasticorMetalNuts ................................... 100

Joining Roll-Grooved Pipe ............................................................................................. 101

Antifreeze Solutions - Pressure Testing CPVC and PVC at Reduced Temperatures ...... 101

Antifreeze Solutions for ABS DWV Systems ................................................................. 102

Underground Installation .............................................................................................. 102

Trenching .................................................................................................................. 102

Bedding and Backﬁlling ............................................................................................. 102

CTS CPVC Under-Slab Installations ............................................................................. 103

ABS and PVC Under-Slab Instalations ........................................................................... 103

In-Slab Installations ...................................................................................................... 103

Testing and Inspection .................................................................................................. 103

Testing DWV System ..................................................................................................... 103

Testing Pressure System ............................................................................................... 104

SPECIAL CONSIDERATIONS

FlowGuard Gold

®

Domestic Water Systems .................................................................. 105

Advantages of a FlowGuard Gold CPVC System ........................................................... 105

Chemical Compatibility with CPVC Products ............................................................... 105

CTS CPVC Pipe Passing Through Studs ........................................................................ 106

Closed-Loop Systems .................................................................................................... 106

Connecting CTS CPVC to Fixtures or Other Materials .......................................... 106-107

Disinfection ................................................................................................................... 107

Elevated-Temperature Performance ....................................................................... 107-108

Horizontal and Vertical Support .................................................................................... 108

HVAC Condensate Drain Lines ...................................................................................... 108

Low Temperature Recommendation .............................................................................. 108

Cold Weather Considerations for CPVC ........................................................................ 109

Heat Build-Up ............................................................................................................... 109

Thermal Conductivity and Sweating of CTS CPVC ................................................ 109-110

Water Hammer Arrestors .............................................................................................. 110

FlowGuard Gold and Corzan Domestic Water Systems Do’s and Dont’s ................ 110-111

Hydronic Heating, Chilled Water or Geothermal Applications .............................. 112-113

Material Selection, Special System Design and Engineering Considerations ........ 114-115

  SelectionofMaterialforSanitaryandStormDrainage ............................................. 114

Engineered Applications ........................................................................................... 114

  UnstableSoil ........................................................................................................... 115

  UsingPlasticsinMulti-StoryConstruction ................................................................ 115

  UsingPlasticsforVentingCombustionGases ............................................................. 115

Repairs or Modiﬁcations to Existing CPVC CTS Systems ............................................. 115

LIMITED WARRANTY ......................................................................................................... 116

FLOWGUARD GOLD CPVC CTS LIMITED WARRANTY ...................................................... 117

TABLE OF CONTENTS

CorzanandFlowGuardGoldareregisteredtrademarksofLubrizolCorp.

5

This is the safety alert symbol. It is used to alert

you to potential personal injury hazards. Obey all

safety messages that follow this symbol to avoid

personal injury or death.

It is important to read and understand this manual. It contains information to help protect your safety and prevent

problems.

GENERAL INFORMATION

Understanding Safety Alert Messages

“WARNING” Indicates a hazardous situation which, if not

avoided, could result in severe injury or death.

“CAUTION” Indicates a hazardous situation which, if not

avoided, could result in minor or moderate injury.

“NOTICE” Indicates a hazardous situation which, if not

avoided, may result in system failure and property damage.

6

Plastics Technical Manual

• WhileABS,PVCandCPVCareverydifferentmaterials,

they share numerous advantages common to plastic piping

systems. Advantages include ease of installation, corrosion

resistance, low friction loss, initial cost, and longevity.

Easy Installation

• ABS, PVC and CPVC systems are light in weight

(approximately one-half the weight of aluminum and

one-sixth the weight of steel) reducing transportation,

handling, and installation cost. They have smooth,

seamlessinteriorwalls.Nospecialtoolsarerequiredfor

cutting. These materials can be installed using the solvent

cement joining technique.

Strength

• ABS,PVCandCPVCproductsarehighlyresilient,tough

and durable with high tensile and high impact strength.

Freedom from Toxicity, Odors, Tastes

• PVCandCPVCpipingsystemsdesignedfordomesticwater

applicationsarelistedtoconformtoNSFInternational

Standard61.ThisHealthEffectsstandardensuresthe

safety of products coming into contact with drinking

water.

Corrosion Free External and Internal

• With many other pipe materials, slight corrosion may

occur. The corroded particles can contaminate the

piped ﬂuid, complicating further processing, or causing

bad taste, odors, or discoloration. This is particularly

undesirable when the piped fluid is for domestic

consumption.WithPVCandCPVC,therearenocorrosive

by-products, therefore, no contamination of the piped

ﬂuid.

Immunity to Galvanic or Electrolytic Attack

• ABS,PVCandCPVCareinherentlyimmunetogalvanic

or electrolytic action. They can be used underground,

underwater, in the presence of metals, and can be

connected to metals.

Fire Resistance

• PVC and CPVC piping systems are self extinguishing

andwillnotsupportcombustion.TheASTME84test

protocol is used to determine the ﬂame and smoke rating

for various materials.

• PVCwillnotpasstheASTME-8425/50amespread

/smokedevelopedtestandisnotacceptableforusein

plenum areas.

• Consult Charlotte Pipe for additional information on

CPVC in plenum applications.

• For plenum applications, follow prevailing code

requirements.

Low Friction Loss

• The smooth interior surfaces of ABS, PVC and CPVC

assure low friction loss and high ﬂow rate. Additionally,

since ABS, PVC and CPVC pipe resist rusting, pitting,

scaling and corrosion, the high ﬂow rate can be maintained

for the life of the piping system.

Low Thermal Conductivity

• PVC and CPVC pipe have a much lower thermal

conductivity factor than metal pipe. Therefore, ﬂuids

being piped maintain a more constant temperature. In

many cases, pipe insulation is not required.

Major Advantages of ABS,

PVC and CPVC Pipe

GENERAL INFORMATION

Tothebestofourknowledgetheinformationcontainedinthispublicationisaccurate.However,CharlottePipeandFoundrydoesnot

assume any liability whatsoever for the accuracy or completeness of such information. Final determination of the suitability of any

information or product for the use to be contemplated is the sole responsibility of the user. The manner of that use and whether there is

any infringement of patents is also the sole responsibility of the user.

To reduce the risk of death or serious injury from an explo-

sion, collapse or projectile hazard and to reduce the risk of

property damage from a system failure:

• Always follow the warnings and procedures provided in

this manual.

• Only use PVC/ABS/CPVC pipe and fitting for the

conveyance of fluids as defined within the applicable

ASTM standards.

• Never use PVC/ABS/CPVC pipe and fittings for the

conveyance of gasses.

• Never use PVC/ABS/CPVC pipe or fittings in structural

application or in any load-bearing applications.

• Never strike the pipe or fittings or drive them into the

ground or into any other hard substance.

7

GENERAL INFORMATION

Testing with or use of compressed air or gas in PVC / ABS

/ CPVC pipe or fittings can result in explosive failures and

cause severe injury or death.

• NEVER test with or transport/store

compressed air or gas in PVC / ABS / CPVC

pipe or fittings.

• NEVER test PVC / ABS / CPVC pipe or

fittings with compressed air or gas, or air

over water boosters.

• ONLY use PVC / ABS / CPVC pipe for water

or approved chemicals.

• Refer to warnings in PPFA User Bulletin

4-80 and ASTM D 1785.

Cost Effective

• ABS,PVCandCPVCproductsareextremelylightweight,

convenient to handle, relatively ﬂexible, and easy to

install. These features lead to lower installed cost than

other piping systems.

Virtually Maintenance Free

• OnceanABS,PVCorCPVCsystemisproperlyselected,

designed, and installed, it is virtually maintenance free.

Therefore, years of trouble-free service can be expected

when using Charlotte Pipe and Foundry ABS, PVC and

CPVC systems.

Handling and Storage of ABS,

PVC and CPVC Pipe

Receiving Pipe

As pipe is received, it must always be thoroughly inspected,

prior to unloading. The person receiving the pipe must look for

any transportation damage caused by over-tightened tie-down

straps, improper treatment, or a shift in the load.

Pipe received in a closed trailer must be inspected as the trailer

is opened. Take extra time to ensure that the pipe has not been

damaged by other materials having been stacked on top of it,

load shift, or rough handling.

Visually examine the pipe ends for any cracks, splits, gouges,

or other forms of damage. Additionally, the pipe should be

inspected for severe deformation which could later cause

joining problems. The entire inside diameter of larger diameter

pipe(4”andabove)mustbecheckedforanyinternalsplitsor

cracks which could have been caused by loading or transit. The

use of a ﬂashlight may be necessary to perform this inspection.

Any damages must be observed by all parties involved,

including the driver, and should be clearly noted on the bill of

ladingand/ordeliveryticket.Acopyofthisdocumentshould

be retained by the receiver. In addition, the manufacturer and

carrier should be notiﬁed, within 24 hours, of any damages,

shortages, or mis-shipped products.

Handling Pipe

The pipe should be handled with reasonable care. Because

thermoplastic pipe is much lighter in weight than metal pipe,

there is sometimes a tendency to throw it around. This should

be avoided.

The pipe should never be dragged or pushed from a truck bed.

Removing and handling pallets of pipe should be done with a

forklift. Loose pipe lengths require special handling to avoid

damage. Precautions to follow when unloading and handling

loose pieces include not banging lengths together or dropping

lengths, even from low heights, on hard or uneven surfaces.

In all cases, severe contact with any sharp objects (rocks,

angle irons, forks on forklifts, etc.) should be avoided. Also,

the pipe should never be lifted or moved by inserting the forks

of a forklift into the pipe ends.

HandlingPVCandparticularlyCPVCpipediametersgreater

than 4-inch requires extra care as the added pipe weight can

cause cracking from relatively minor impacts. Also, plastic

pipe becomes more brittle as the temperature decreases. The

impact strength and ﬂexibility of PVC and especially CPVC

pipe are reduced. Therefore, take extra care when handling

skids or loose lengths when the temperature drops below 50°F.

Storing Pipe

If possible, pipe should be stored inside. When this is not

possible, the pipe should be stored on level ground which is

dry and free from sharp objects. If different schedules of pipe

are stacked together, the pipe with the thickest walls should

be on the bottom.

If the pipe is in pallets, the pallets should be stacked with the

pallet boards touching, rather than pallet boards being placed

on the pipe. This will prevent damage to or bowing of the pipe.

If the pipe is stored in racks, it should be continuously

supported along its length. If this is not possible, the spacing

ofthesupportsshouldnotexceedthreefeet(3’).

The pipe should be protected from the sun and be in an area

with proper ventilation. This will lessen the effects of ultraviolet

rays and help prevent heat build-up.

8

Plastics Technical Manual

ABS DWV

 Schedule40DWVFoamCorePipe ASTMD3965 ASTMF628

 Schedule40DWVFittings ASTMD3965 ASTMD2661

PVC DWV

 Schedule40DWVPipe ASTMD1784

ASTMD2665&ASTMD1785

 Schedule40DWVFoamCorePipe ASTMD4396 ASTMF891

 Schedule40DWVPipewithRecycledContent ASTMD4396 ASTMF1760

 Schedule40DWVFittings ASTMD1784 ASTMD2665

 FabricatedSchedule40DWVFittings ASTMD1784 ASTMF1866

PVC Pressure

 Schedule40PlainEndPipe ASTMD1784 ASTMD1785

 Schedule40BellEndPipe ASTMD1784 ASTMD1785

 Schedule40BellEndWellCasing ASTMD1784 ASTMD1785&ASTMF480

 SDR21(PR200)BellEndPipe ASTMD1784 ASTMD2241

 SDR26(PR160)BellEndPipe ASTMD1784 ASTMD2241

 Schedule40Fittings ASTMD1784 ASTMD2466

 Schedule80PlainEndPipe ASTMD1784 ASTMD1785

 Schedule80Fittings ASTMD1784 ASTMD2464&ASTMD2467

 SpecicGravity g/cc 1.05 D792 1.40 D792

 TensileStrength(73°F)Minimum Psi 4,500 D638 7,000 D638

 ModulusofElasticityinTension(73°F)Minimum Psi 240,000 D638 400,000 D638

Flexural Strength (73°F) Psi 10,585 D 790 14,000 D 790

 IzodImpact(notchedat73°F)Minimum ftlb/in.ofnotch 6.00 D256 0.65 D256

 Hardness(DurometerD)  70 D2240 80±3 D2240

 Hardness(RockwellR)  100 D785 110-120 D785

Compressive Strength (73°F) Psi 7,000 D 695 9,600 D 695

 HydrostaticDesignStress Psi N/A  2,000 D1598

 CoefcientofLinearExpansion in./in./°F 5.5x10

-5

D 696 3.0 x 10

-5

D 696

 HeatDistortionTemperatureat264psiMinimum degreesF 180 D648 160 D648

 CoefcientofThermalConductivity BTU/hr/sqft/°F/in. 1.1 C177 1.2 C177

 SpecicHeat BTU/°F/lb 0.35 D2766 0.25 D2766

 WaterAbsorption(24hrsat73°F) %weightgain 0.40 D570 .05 D570

Cell Classiﬁcation - Pipe 42222 D 3965 12454 D 1784

Cell Classiﬁcation - Fittings 32222 D 3965 12454 D 1784

Burning Rate Self Ext. D 635

 BurningClass    V-0 UL94**

MATERIAL DIMENSIONS

PROPERTY UNITS ABS ASTM NO. PVC ASTM NO.

ABS and PVC Standards

*Abovedataisbaseduponinformationprovidedbytherawmaterialmanufacturers.Itshouldbeusedonlyasa

recommendationandnotasaguaranteeofperformance.**UnderwritersLaboratoriesstandard

TYPE PIPE / FITTING

STANDARD SPECIFICATIONS

GENERAL INFORMATION

Physical Properties of Charlotte Pipe

®

ABS and PVC Materials

*

9

CPVC Pressure

CPVCSchedule80PlainEndPipe(Corzan) ASTMD1784 ASTMF441

CPVCSchedule80Fittings(Corzan) ASTMD1784 ASTMF437andASTMF439

CPVCCTSTubeandFittings(FlowGuardGold,ReUze

®

) ASTMD1784 ASTMD2846

PROPERTY CPVC 4120 UNITS ASTM No.

CPVC Standards

*Abovedataisbaseduponinformationprovidedbytherawmaterialmanufacturers.Itshouldbeusedonlyasa

recommendationandnotasaguaranteeofperformance.**UnderwritersLaboratoriesstandard

TYPE PIPE / FITTINGS

STANDARD SPECIFICATIONS

MATERIAL DIMENSIONS

 SpecicGravity 1.55 g/cc D792

 TensileStrength(73°F)Minimum 7,000 psi D638

 ModulusofElasticityinTension(73°F) 360,000 psi D638

Flexural Strength (73°F) 15,100 psi D 790

 IzodImpactCellClass23447(notchedat73°F)Minimum 1.5 ftlb/in.ofnotch D256

 IzodImpactCellClass24448(notchedat73°F)Minimum 5.0 ftlb/in.ofnotch D256

 Hardness(DurometerD) —  D2240

 Hardness(RockwellR) 119  D785

Compressive Strength (73°F) 10,100 psi D 695

 HydrostaticDesignStress 2,000 psi

Coefﬁcient of Linear Expansion 3.4 x 10

-5

 in./in./°F D696

 HeatDistortionTemperatureat264psiMinimum 212(CellClass23447) degreesF D648

 HeatDistortionTemperatureat264psiMinimum 230(CellClass24448) degreesF D648

 CoefcientofThermalConductivity .95 BTU/hr/sqft/°F/in. C177

 SpecicHeat .34 BTU/°F/lb D2766

 WaterAbsorption(24hrsat73°F) .03 %weightgain D570

Cell Classiﬁcation 23447 - 24448 D 1784

Burning Rate Self Extinguishing D 635

 BurningClass V-0  UL94**

GENERAL INFORMATION

Physical Properties of FlowGuard Gold

®

, ReUze

®

& Corzan

®

CPVC Materials

*

CorzanandFlowGuardGoldareregisteredtrademarksofLubrizolCorp.

10

Plastics Technical Manual

Product Speciﬁcations

System: ABS Cellular Core (Foam Core) Pipe and ABS DWV Fitting System

Scope: ThisspecicationcoversABScellularcore(foamcore)pipeandABSDWVttingsusedinsanitary

drain,waste,andvent(DWV),sewer,andstormdrainageapplications.Thissystemisintendedforusein

non-pressure applications where the operating temperature will not exceed 140°F.

Speciﬁcation: Pipe shall be manufactured from virgin rigid ABS (acrylonitrile-butadiene-styrene) compounds with a

CellClassof42222asidentiedinASTMD3965.FittingsshallbemanufacturedfromvirginrigidABS

compoundswithaCellClassof32222asidentiedinASTMD3965.

 ABScellularcorepipeshallbeIronPipeSize(IPS)conformingtoASTMF628.ABSDWVttings

shallconformtoASTMD2661.Pipeandttingsshallbemanufacturedasasystemandbetheproduct

ofonemanufacturer.AllpipeandttingsshallbemanufacturedintheUnitedStates.Allsystemsshall

utilizeaseparatewasteandventsystem.PipeandttingsshallconformtoNSFInternationalStandard

14.

Installation shall comply with the latest installation instructions published by Charlotte Pipe and Foundry

and shall conform to all applicable plumbing, ﬁre, and building code requirements. Buried pipe shall

beinstalledinaccordancewithASTMD2321andASTMF1668.Solventcementjointsshallbemade

withasolventcementconformingtoASTMD2235.Thesystemshallbeprotectedfromchemicalagents,

ﬁre stopping materials, thread sealant, or other aggressive chemical agents not compatible with ABS

compounds. Systems shall be hydrostatically tested after installation. WARNING!Nevertestwithor

transport/storecompressedairorgasinABSpipeorttings.

Referenced Standards*:

 ASTMD3965 RigidABSCompounds

 ASTMF628 Co-extrudedABSPipewithCellularCore

 ASTMD2661 ABSDrain,Waste,andVentFittings

 ASTMD2235 SolventCementsforABSPipeandFittings

 ASTMD2321 UndergroundInstallationofThermoplasticPipe(non-pressureapplications)

 ASTMF1668 ProceduresforBuriedPlasticPipe

 NSFStandard14 PlasticPipingComponentsandRelatedMaterials

*Note:Latestrevisionofeachstandardapplies.

Short Speciﬁcation:

Pipe and fittings shall be manufactured from ABS compound with a cell class of 42222

for pipe and 32222 for fittings as per ASTM D 3965 and conform with NSF International

Standard14.Pipeshallbeironpipesize(IPS)conformingtoASTMF628.Fittingsshallconformto

ASTMD2661.

All pipe and ﬁttings shall be produced by a single manufacturer and shall be installed in accordance with

manufacturer’s recommendations and applicable code requirements.Buriedpipeshallbeinstalled in

accordancewithASTMD2321andASTMF1668.SolventcementshallconformtoASTMD2235.The

system is to be manufactured by Charlotte Pipe and Foundry Company and is intended for non-pressure

drainage applications where the temperature will not exceed 140°F.

GENERAL INFORMATION

11

Product Speciﬁcations

System: PVC Schedule 40 Solid Wall Pipe and PVC DWV Fitting System

Scope: ThisspecicationcoversPVCSchedule40solidwallpipeandPVCDWVttingsusedinsanitarydrain,

waste,andvent(DWV),sewer,andstormdrainageapplications.Thissystemisintendedforuseinnon-

pressure applications where the operating temperature will not exceed 140°F.

Speciﬁcation: Pipe and ﬁttings shall be manufactured from virgin rigid PVC (polyvinyl chloride) vinyl compounds with

aCellClassof12454asidentiedinASTMD1784.

 PVCSchedule40pipeshallbeIronPipeSize(IPS)conformingtoASTMD1785andASTMD2665.

InjectionmoldedPVCDWVttingsshallconformtoASTMD2665.FabricatedPVCDWVttingsshall

conformtoASTMF1866.Pipeandttingsshallbemanufacturedasasystemandbetheproductofone

manufacturer.AllpipeandttingsshallbemanufacturedintheUnitedStates.Allsystemsshallutilize

aseparatewasteandventsystem.PipeandttingsshallconformtoNSFInternationalStandard14.

Installation shall comply with the latest installation instructions published by Charlotte Pipe and Foundry

and shall conform to all applicable plumbing, building, and ﬁre code requirements. Buried pipe shall be

installedinaccordancewithASTMD2321andASTMF1668.Solventcementjointsshallbemadein

atwostepprocesswithprimerconformingtoASTMF656andsolventcementconformingtoASTM

D 2564. The system shall be protected from chemical agents, ﬁre stopping materials, thread sealant,

plasticizedvinyl products, orotheraggressivechemicalagents notcompatiblewithPVCcompounds.

Systems shall be hydrostatically tested after installation. WARNING! Nevertestwithortransport/store

compressed air or gas in PVC pipe or ﬁttings.

Referenced Standards*:

 ASTMD1784 RigidVinylCompounds

 ASTMD1785 PVCPlasticPipe,Schedule40

 ASTMD2665 PVCDrain,Waste,andVentPipe&Fittings

 ASTMD2564 SolventCementsforPVCPipeandFittings

 ASTMD2321 UndergroundInstallationofThermoplasticPipe(non-pressureapplications)

 ASTMF656 PrimersforPVCPipeandFittings

 ASTMF1668 ProceduresforBuriedPlasticPipe

 ASTMF1866 FabricatedPVCDWVFittings

 NSFStandard14 PlasticPipingComponentsandRelatedMaterials

*Note:Latestrevisionofeachstandardapplies.

Short Speciﬁcation:

PipeandttingsshallbemanufacturedfromPVCcompoundwithacellclassof12454perASTMD1784

andconformwithNSFInternationalStandard14.Pipeshallbeironpipesize(IPS)conformingtoASTM

D1785andASTMD2665.InjectionmoldedttingsshallconformtoASTMD2665.Fabricatedttings

shallconformtoASTMF1866.

All pipe and ﬁttings shall be produced by a single manufacturer and shall be installed in accordance with

manufacturer’s recommendations and applicable code requirements. Buried pipe shall be installed in

accordancewithASTMD2321andASTMF1668.SolventcementsshallconformtoASTMD2564,primer

shallconformtoASTMF656.ThesystemistobemanufacturedbyCharlottePipeandFoundryCompany

and is intended for non-pressure drainage applications where the temperature will not exceed 140°F.

GENERAL INFORMATION

12

Plastics Technical Manual

Product Speciﬁcation

System: PVC Cellular Core (Foam Core) Pipe and PVC DWV Fitting Systems

Scope: Thisspecication coversPVCcellularcore(foam core)pipeandPVC DWVttingsusedinsanitary

drain,waste,andvent(DWV),sewer,andstormdrainageapplications.Thissystemisintendedforusein

non-pressure applications where the operating temperature will not exceed 140°F.

Speciﬁcation: Pipe shall be manufactured from virgin rigid PVC (polyvinyl chloride) vinyl compounds with a Cell Class

of11432asidentiedinASTMD4396.FittingsshallbemanufacturedfromvirginrigidPVC(polyvinyl

chloride)vinylcompoundswithaCellClassof12454asidentiedinASTMD1784.

 PVCcellularcorepipeshallbeIronPipeSize(IPS)conformingtoASTMF891.InjectionmoldedPVC

DWVttingsshallconformtoASTMD2665.FabricatedPVCDWVttingsshallconformtoASTMF

1866. Pipe and ﬁttings shall be manufactured as a system and be the product of one manufacturer. All

pipeandttingsshallbemanufacturedintheUnitedStates.Allsystemsshallutilizeaseparatewaste

andventsystem.PipeandttingsshallconformtoNSFInternationalStandard14.

Installation shall comply with the latest installation instructions published by Charlotte Pipe and Foundry

and shall conform to all applicable plumbing, ﬁre, and building code requirements. Buried pipe shall be

installedinaccordancewithASTMD2321andASTMF1668.Solventcementjointsshallbemadein

atwostepprocesswithprimerconformingtoASTMF656andsolventcementconformingtoASTM

D 2564. The system shall be protected from chemical agents, ﬁre stopping materials, thread sealant,

plasticizedvinyl products, orotheraggressivechemicalagents notcompatiblewithPVCcompounds.

Systems shall be hydrostatically tested after installation. WARNING! Nevertestwithortransport/store

compressed air or gas in PVC pipe or ﬁttings.

Referenced Standards*:

 ASTMD4396 CompoundsforCellularCorePipe

 ASTMF891 Co-extrudedPVCPipewithCellularCore

 ASTMD2665 PVCDrain,Waste,andVentFittings

 ASTMD2564 SolventCementsforPVCPipeandFittings

 ASTMD2321 UndergroundInstallationofThermoplasticPipe(non-pressureapplications)

 ASTMF656 PrimersforPVCPipeandFittings

 ASTMF1668 ProceduresforBuriedPlasticPipe

 ASTMF1866 FabricatedPVCDWVFittings

 NSFStandard14 PlasticPipingComponentsandRelatedMaterials

*Note:Latestrevisionofeachstandardapplies.

Short Speciﬁcation:

PipeshallbemanufacturedfromPVCcompoundwithacellclassof11432perASTMD4396and12454

perASTMD1784forttingsandconformwithNSFInternationalStandard14.Pipeshallbeironpipe

size(IPS)conformingtoASTMF891.InjectionmoldedPVCDWVttingsshallconformtoASTMD

2665.FabricatedPVCDWVttingsshallconformtoASTMF1866.

All pipe and ﬁttings shall be produced by a single manufacturer and shall be installed in accordance with

manufacturer’s recommendations and applicable code requirements. Buried pipe shall be installed in

accordancewithASTMD2321andASTMF1668.SolventcementsshallconformtoASTMD2564,primer

shallconformtoASTMF656.ThesystemistobemanufacturedbyCharlottePipeandFoundryCompany

and is intended for non-pressure drainage applications where the temperature will not exceed 140°F.

GENERAL INFORMATION

13

GENERAL INFORMATION

System: RePVC

®

– PVC Schedule 40 Pipe with Recycled Content and PVC DWV Fitting System

Scope:

 ThisspecicationcoversPVCSchedule40pipewithrecycledcontentandPVCDWVttingsusedinsanitary

drain,waste,andvent (DWV),sewerandstorm drainageapplications. Thissystemisintendedfor usein

non-pressure applications where the operating temperature will not exceed 140°F.

Speciﬁcation:

Inside and outside layers of pipe shall be manufactured from virgin rigid PVC (polyvinyl chloride) vinyl

compoundswithaminimumcellclassof11432perASTMD4396.Centerlayerofpipeshallbemanufactured

fromrecycledPVCcompoundswithaminimumcellclassof11211perASTMD4396.Fittingsshallbe

manufactured from virgin rigid PVC (polyvinyl chloride) vinyl compounds with a cell class of 12454 as

identiedinASTMD1784.

 Centerlayerofpipeshallbecomprisedof100%recycledmaterialandmakeup30–80%ofthepipe’soverall

wall thickness.

 CoextrudedPVCpipewithrecycledcontentshallbeSchedule40ironpipesize(IPS)conformingtoASTM

F1760.InjectionmoldedPVCDWVttingsshallconformtoASTMD2665.FabricatedPVCDWVttings

shallconformtoASTMF1866.Pipeandttingsshallbemanufacturedasasystemandbetheproductof

onemanufacturer.AllpipeandttingsshallbemanufacturedintheUnitedStates.Allsystemsshallutilize

aseparatewasteandventsystem.PipeandttingsshallconformtoNSFInternationalStandard14.

Installation shall comply with the latest installation instructions published by Charlotte Pipe and Foundry

and shall conform to all applicable plumbing, ﬁre, and building code requirements. Buried pipe shall be

installedinaccordancewithASTMD2321andASTMF1668.Solventcementjointsshallbemadeina

twostepprocesswithprimerconformingtoASTMF656andsolventcementconformingtoASTMD2564.

The system shall be protected from chemical agents, re stopping materials, thread sealant, plasticized

vinyl products, or other aggressive chemical agents not compatible with PVC compounds. Systems shall be

hydrostatically tested after installation. WARNING!

Nevertestwithortransport/storecompressedairor

gas in PVC pipe or ﬁttings.

Referenced Standards*:

 ASTMD4396 CompoundsforCellularCorePipe

 ASTMF1760 Co-extrudedPVCPipewithRecycledContent

 ASTMD2665 PVCDrain,Waste,andVentFittings

 ASTMD2564 SolventCementsforPVCPipeandFittings

 ASTMD2321 UndergroundInstallationofThermoplasticPipe(non-pressureapplications)

 ASTMF656 PrimersforPVCPipeandFittings

 ASTMF1668 ProceduresforBuriedPlasticPipe

 ASTMF1866 FabricatedPVCDWVFittings

 NSFStandard14 PlasticPipingComponentsandRelatedMaterials

*Note:Latestrevisionofeachstandardapplies.

Short Speciﬁcation:

Pipe shall be manufactured from PVC compound with a minimum cell class of 11432 for the inside and

outsidelayersand11211forthecenterlayerperASTMD4396.Centerlayerofpipeshallbecomprisedof

100%recycledmaterialandmakeup30–80%oftheoverallwallthickness.PipeshallbeSchedule40iron

pipesize(IPS)conformingtoASTMF1760.

 Fittingsshall be manufactured from virgin rigid PVCcompound with a cellclass of 23447 per ASTM D

1784andconformwithNSFInternationalStandard14.InjectionmoldedPVCDWVttingsshallconform

toASTMD2665.FabricatedPVCDWVttingsshallconformtoASTMF1866.

All pipe and ﬁttings shall be produced by a single manufacturer and be installed in accordance with manufac-

turer’srecommendationsandapplicablecoderequirements.Buriedpipeshallbeinstalledinaccordancewith

ASTMD2321andASTMF1668.SolventcementsshallconformtoASTMD2564,primershallconform

toASTMF656.ThesystemtobemanufacturedbyCharlottePipeandFoundryCo.andisintendedfornon-

pressure drainage applications where the temperature will not exceed 140°F.

RePVC is a registered trademark of Charlotte Pipe and Foundry Company.

Product Speciﬁcation

14

Plastics Technical Manual

Product Speciﬁcations

System: PVC Schedule 40 Pressure Pipe and Fitting System

Scope: This speciﬁcation covers PVC Schedule 40 pipe and ﬁttings for pressure applications. This system is

intended for pressure applications where the operating temperature will not exceed 140°F.

Speciﬁcation: Pipe and ﬁttings shall be manufactured from virgin rigid PVC (polyvinyl chloride) vinyl compounds with

aCellClassof12454asidentiedinASTMD1784.

 PVCSchedule40pipeshallbeIronPipeSize(IPS)conformingtoASTMD1785.PVCSchedule40

ttingsshallconformtoASTMD2466.Pipeandttingsshallbemanufacturedasasystemandbethe

productofonemanufacturer.AllpipeandttingsshallbemanufacturedintheUnitedStates.Pipeand

ttingsshallconformtoNSFInternationalStandard61orthehealtheffectsportionofNSFStandard

14.

Installation shall comply with the latest installation instructions published by Charlotte Pipe and Foundry

and shall conform to all applicable plumbing, building, and ﬁre code requirements. Buried pipe shall be

installedinaccordancewithASTMF1668andASTMD2774.Solventcementjointsshallbemadein

atwostepprocesswithprimerconformingtoASTMF656andsolventcementconformingtoASTM

D 2564. The system shall be protected from chemical agents, ﬁre stopping materials, thread sealant,

plasticizedvinyl products, orotheraggressivechemicalagents notcompatiblewithPVCcompounds.

Systems shall be hydrostatically tested after installation. WARNING! Nevertestwithortransport/store

compressed air or gas in PVC pipe or ﬁttings.

Referenced Standards*:

 ASTMD1784 RigidVinylCompounds

 ASTMD1785 PVCPlasticPipe,Schedule40

 ASTMD2466 PVCPlasticFittings,Schedule40

 ASTMD2564 SolventCementsforPVCPipeandFittings

 ASTMD2774 UndergroundInstallationofThermoplasticPressurePiping

 ASTMF656 PrimersforPVCPipeandFittings

 ASTMF1668 ProceduresforBuriedPlasticPipe

 NSFStandard14 PlasticPipingComponentsandRelatedMaterials

 NSFStandard61 DrinkingWaterSystemComponents-HealthEffects

*Note:Latestrevisionofeachstandardapplies.

Short Speciﬁcation:

 PipeandttingsshallbemanufacturedfromPVCcompoundwithacellclassof12454perASTMD1784

andconformwithNSFInternationalStandards14and61.Pipeshallbeironpipesize(IPS)conforming

toASTMD1785.FittingsshallconformtoASTMD2466.

All pipe and ﬁttings shall be produced by a single manufacturer and shall be installed in accordance with

manufacturer’s recommendations and applicable code requirements.Buriedpipeshallbeinstalled in

accordancewithASTMF1668andASTMD2774.SolventcementsshallconformtoASTMD2564,

primershallconformtoASTMF656.ThesystemistobemanufacturedbyCharlottePipeandFoundry

Company and is intended for pressure applications where the temperature will not exceed 140°F.

GENERAL INFORMATION

15

Product Speciﬁcations

System: PVC SDR Pressure Pipe and Fitting System

Scope: This speciﬁcation covers PVC Standard Dimensional Ratio (SDR) pipe and ﬁttings for pressure applications.

This system is intended for pressure applications where the operating temperature will not exceed 140°F.

Speciﬁcation: Pipe and ﬁttings shall be manufactured from virgin rigid PVC (polyvinyl chloride) vinyl compounds with

aCellClassof12454asidentiedinASTMD1784.

 PVCSDRpipeshallbeIronPipeSize(IPS)conformingtoASTMD2241forplainendpipeandASTM

D2672forbelled-endpipe.PVCSchedule40(IPS)ttingsshallconformtoASTMD2466.Pipeand

ﬁttings shall be manufactured as a system and be the product of one manufacturer. All pipe and ﬁttings

shallbemanufacturedintheUnitedStates.PipeandttingsshallconformtoNSFInternationalStandard

61orthehealtheffectsportionofNSFStandard14.

Installation shall comply with the latest installation instructions published by Charlotte Pipe and Foundry

and shall conform to all applicable plumbing, building, and ﬁre code requirements. Buried pipe shall be

installedinaccordancewithASTMF1668andASTMD2774.Solventcementjointsshallbemadeina

twostepprocesswithprimerconformingtoASTMF656andsolventcementconformingtoASTMD2564.

Thesystemshallbeprotectedfromchemicalagents,restoppingmaterials,threadsealant,plasticized

vinyl products, or other aggressive chemical agents not compatible with PVC compounds. Systems shall

be hydrostatically tested after installation. WARNING! Nevertestwithortransport/storecompressedair

or gas in PVC pipe or ﬁttings.

Referenced Standards*:

 ASTMD1784 RigidVinylCompounds

 ASTMD2241 PVCPressureRatedPipe(SDRSeries)

 ASTMD2672 JointsforIPSPVCPipeUsingSolventCement

 ASTMD2466 PVCPlasticFittings,Schedule40

 ASTMD2564 SolventCementsforPVCPipeandFittings

 ASTMD2774 UndergroundInstallationofThermoplasticPressurePiping

 ASTMF656 PrimersforPVCPipeandFittings

 ASTMF1668 ProceduresforBuriedPlasticPipe

 NSFStandard14 PlasticPipingComponentsandRelatedMaterials

 NSFStandard61 DrinkingWaterSystemComponents-HealthEffects

*Note:Latestrevisionofeachstandardapplies.

Short Speciﬁcation:

 PipeandttingsshallbemanufacturedfromPVCcompoundwithacellclassof12454perASTMD1784

andconformwithNSFInternationalStandards14and61.Pipeshallbeironpipesize(IPS)conforming

toASTMD2241forplain-endpipeandASTMD2672forbelled-endpipe.PVCSchedule40ttingsshall

conformtoASTMD2466.

All pipe and ﬁttings shall be produced by a single manufacturer and shall be installed in accordance with

manufacturer’s recommendations and applicable code requirements. Buried pipe shall be installed in

accordancewithASTMF1668andASTMD2774.SolventcementsshallconformtoASTMD2564,

primershallconformtoASTMF656.ThesystemistobemanufacturedbyCharlottePipeandFoundry

Company and is intended for pressure applications where the temperature will not exceed 140°F.

GENERAL INFORMATION

16

Plastics Technical Manual

Product Speciﬁcations

System: PVC Schedule 80 Pressure Pipe and Fitting System

Scope: This speciﬁcation covers PVC Schedule 80 pipe and ﬁttings for pressure applications. This system is intended

for pressure applications where the operating temperature will not exceed 140°F.

Speciﬁcation: Pipe and ﬁttings shall be manufactured from virgin rigid PVC (polyvinyl chloride) vinyl compounds with a

CellClassof12454asidentiedinASTMD1784.

 PVCSchedule80pipeshallbeIronPipeSize(IPS)conformingtoASTMD1785.PVCSchedule80ttings

shallconformtoASTMD2467.PVCSchedule80threadedttingsshallconformtoASTMD2464.Pipe

and ﬁttings shall be manufactured as a system and be the product of one manufacturer. All pipe and ﬁttings

shallbemanufacturedintheUnitedStates.PipeandttingsshallconformtoNSFInternationalStandard

61orthehealtheffectsportionofNSFStandard14.

Installation shall comply with the latest installation instructions published by Charlotte Pipe and Foundry

and shall conform to all applicable plumbing, building, and ﬁre code requirements. Buried pipe shall be

installedinaccordancewithASTMF1668andASTMD2774.Solventcementjointsshallbemadeinatwo

stepprocessusingIPSP-70orOateyIndustrialGradeprimersandsolventcementconformingtoASTMD

2564.Thesystemshallbeprotectedfromchemicalagents,restoppingmaterials,threadsealant,plasticized

vinyl products, or other aggressive chemical agents not compatible with PVC compounds. Systems shall be

hydrostatically tested after installation. WARNING! Nevertestwithortransport/storecompressedairor

gas in PVC pipe or ﬁttings.

Referenced Standards*:

 ASTMD1784 RigidVinylCompounds

 ASTMD1785 PVCPlasticPipe,Schedule80

 ASTMD2464orD2467 PVCThreadedFittings,Schedule80

 ASTMD2467 PVCSocketFittings,Schedule80

 ASTMD2564 SolventCementsforPVCPipeandFittings

 ASTMD2774 UndergroundInstallationofThermoplasticPressurePiping

 ASTMF1668 ProceduresforBuriedPlasticPipe

 NSFStandard14 PlasticPipingComponentsandRelatedMaterials

 NSFStandard61 DrinkingWaterSystemComponents-HealthEffects

*Note:Latestrevisionofeachstandardapplies.

Short Speciﬁcation:

 PipeandttingsshallbemanufacturedfromPVCcompoundwithacellclassof12454perASTMD1784

andconformwithNSFInternationalStandards14and61.Pipeshallbeironpipesize(IPS)conforming

toASTMD1785.SocketttingsshallconformtoASTMD2467;threadedttingsshallconformtoASTM

D2464orD2467.FlangesshallmeettheboltpatternrequirementsofANSI/ASMEB16.5.

All pipe and ﬁttings shall be produced by a single manufacturer and shall be installed in accordance with

manufacturer’s recommendations and applicable code requirements.  Buried pipe shall be installed in

accordancewithASTMF1668andASTMD2774.SolventcementsshallconformtoASTMD2564,primer

shall be IPS P-70 or Oatey Industrial Grade. The system is to be manufactured by Charlotte Pipe and Foundry

Company and is intended for pressure applications where the temperature will not exceed 140°F.

GENERAL INFORMATION

17

System: FlowGuard Gold® CPVC Copper Tube Size (CTS) Hot and Cold Domestic Water Distribution

System

Scope: ThisspecicationcoversCopperTubeSize(CTS)CPVCmanufacturedtostandarddimensionalratio(SDR)

11 for hot and cold domestic water distribution. This system is intended for pressure applications where

the operating temperature will not exceed 180°F at 100 psi.

Speciﬁcation: Pipe and ﬁttings shall be manufactured from virgin rigid Chlorinated Poly (Vinyl Chloride) (CPVC)

compoundswithaCellClassof24448forpipeand23447forttingsperASTMD1784.

 FlowGuardGoldCTSCPVCpipeandttingsshallconformtoASTMD2846.Pipeandttingsshallbe

manufactured as a system and be the product of one manufacturer. All pipe and ﬁttings shall be manufactured

intheUnitedStates.PipeandttingsshallconformtoNSFInternationalStandards14and61.

Installation shall comply with latest installation instructions published by Charlotte Pipe and Foundry and

shall conform to all applicable plumbing, building and ﬁre code requirements. Buried pipe shall be installed

inaccordancewithASTMF1668andASTMD2774.SolventweldjointsshallbemadeusingCPVCcement

conformingtoASTMF493.Yellowone-stepcementmaybeusedwithoutprimer.Ifaprimerisrequired

byapplicableplumbingorbuildingcodes,thenaprimerconformingtoASTMF656shouldbeused.The

systemshallbeprotectedfromchemicalagents,restoppingmaterials,threadsealant,plasticizedvinyl

products or other aggressive chemical agents not compatible with CPVC compounds. Systems shall be

hydrostatically tested after installation. WARNING! Nevertestwithortransport/storecompressedairor

gas in CPVC pipe or ﬁttings.

Referenced Standards*:

 ASTMD1784 RigidVinylCompounds

 ASTMD2774 UndergroundInstallationofThermoplasticPressurePiping

 ASTMD2846 CPVCPlasticHotandColdWaterDistributionSystem

 ASTMF493 SolventCementsforCPVCPipeandFittings

 ASTMF1668 ProceduresforBuriedPlasticPipe

 NSFStandard14 PlasticPipingComponentsandRelatedMaterials

 NSFStandard61 DrinkingWaterSystemComponents-HealthEffects

*Note:Latestrevisionofeachstandardapplies.

Short Speciﬁcation:

Speciﬁcation for FlowGuard Gold CPVC Copper Tube Size (CTS) Hot and Cold Domestic Water

Distribution System

All pipe and ﬁttings shall be manufactured from CPVC compound with a cell class of 24448 for pipe and

23447forttingsasperASTMD1784andconformwithNSFInternationalStandards14and61.

Pipe and ﬁttings to be FlowGuard Gold

®

CPVCCopperTubeSizemanufacturedtostandarddimensionratio

(SDR)11andshallconformtoASTMD2846.Transitionttingstohavebrassmaleorfemalethreads

with integral CPVC socket connections as manufactured by Charlotte Pipe and Foundry Company.

All pipe and ﬁttings shall be produced by a single manufacturer and shall be installed in accordance

withmanufacturer’srecommendationsandapplicablecoderequirements.Buriedpipeshallbeinstalled

inaccordancewithASTMF1668andASTMD2774.SolventcementshallconformtoASTMF493

and system may be installed with approved one-step cement. Pipe and ﬁttings are to be manufactured by

Charlotte Pipe and Foundry Company and are intended for hot and cold water distribution systems.

Product Speciﬁcations

GENERAL INFORMATION

FlowGuardGoldandCorzanareregisteredtrademarksofLubrizolCorp.

18

Plastics Technical Manual

System: ReUze

®

CPVC Copper Tube Size (CTS) Non-Potable Water Distribution System

Scope: ThisspecicationcoversCopperTubeSize(CTS)CPVCmanufacturedtostandarddimensionalration

(SDR) 11 for non-potable water distribution. This system is intended for pressure applications where the

operating temperature will not exceed 180˚F at 100 psi.

Speciﬁcation: Pipe and ﬁttings shall be manufactured from virgin rigid Chlorinated Poly (Vinyl Chloride) (CPVC)

compoundswithaCellClassof24448asidentiedinASTMD1784.

 ReUzeCTSCPVCpipeandttingsshallconformtoASTMD2846.Pipeandttingsshallbemanufactured

as a system and be the product of one manufacturer. All pipe and ﬁttings shall be manufactured in the

UnitedStates.PipeandttingsshallconformtoNSFInternationalStandard14.Thepipeshallbelisted

byNSFInternationalforreclaimedwaterandbearthemark“NSF-rw.”

Installation shall comply with latest installation instructions published by Charlotte Pipe and Foundry

and shall conform to all applicable plumbing, building and ﬁre code requirements. Buried pipe shall

beinstalledinaccordancewithASTMF1668andASTMD2774.Solventweldjointsshallbemade

usingCPVCcementconformingtoASTMF493.Yellowone-stepcementmaybeusedwithoutprimer.

Ifaprimerisrequiredbyapplicableplumbingorbuildingcodes,thenaprimerconformingtoASTM

F 656 should be used. The system shall be protected from chemical agents, ﬁre stopping materials,

threadsealant,plasticizedvinylproductsorotheraggressivechemicalagentsnotcompatiblewithCPVC

compounds. System shall be hydrostatically tested after installation. WARNING! Never testwith or

transport/storecompressedairorgasinCPVCpipeorttings.

Referenced Standards*:

 ASTMD1784 RigidVinylCompounds

 ASTMD2774 UndergroundInstallationofThermoplasticPressurePiping

 ASTMD2846 CPVCPlasticHotandColdWaterDistributionSystem

 ASTMF493 SolventCementsforCPVCPipeandFittings

 ASTMF1668 ProceduresforBuriedPlasticPipe

 NSFStandard14 PlasticPipingComponentsandRelatedMaterials

*Note:Latestrevisionofeachstandardapplies.

Short Speciﬁcation:

All pipe and ﬁttings shall be manufactured from CPVC compound with a cell class of 24448 for pipe and

23447forttingsasperASTMD1784,conformwithNSFInternationalStandard14.Thepipeshall

belistedbyNSFInternationalforreclaimedwaterandbearthemark“NSF-rw.”

 1⁄2”through2”sizes:ReUze

®

made with FlowGuard Gold

®

CPVCCopperTubeSizemanufacturedto

standarddimensionratio(SDR)11andshallconformtoASTMD2846.Pipeshallbepurplepigmented

andhavetworowsofmarking180˚aparttoinclude“WARNING: NON-POTABLE WATER DO NOT

DRINK”.Fittings shall be either tan or purple in color.Transition ttings shall have brass male or

female connections with integral CPVC socket connections as manufactured by Charlotte Pipe and

Foundry Company.

All pipe and ﬁttings shall be produced by a single manufacturer and be installed in accordance with

manufacturer’s recommendations and applicable code requirements. System shall be joined using

approvedone-stepsolventcementconformingtoASTMF493.Pipeandttingsshallbemanufactured

by Charlotte Pipe and Foundry Company and are intended for hot and cold non-potable water distribution

systems.

Product Speciﬁcations

GENERAL INFORMATION

ReUzeisaregisteredtrademarkofCharlottePipeandFoundryCompany.

19

Product Speciﬁcations

System: PVC SDR 35 Gravity Sewer Pipe

Scope: ThisspecicationcoversPVCStandardDimensionRatio(SDR)35PSMpipeforgravitysewerandsurface

water applications with a pipe stiffness of 46. This product is intended for gravity applications where the

operating temperature will not exceed 140°F.

Speciﬁcation: Pipe shall be manufactured from virgin rigid PVC (polyvinyl chloride) vinyl compounds with a cell class

of12364asidentiedinASTMD1784.Therequirementsofthisspecicationareintendedtoprovide

pipe suitable for non-pressure drainage and surface water.

 PVCSDR35PSMpipeshallconformtoASTMD3034forgasketorsolventweldpipewithaminimum

pipestiffnessof46.GasketsshallconformtoASTMF477.Theterm“PSM”isnotanacronym,but

rather an arbitrary designation for a product having certain dimensions.

Installation shall comply with the latest installation instructions published by Charlotte Pipe and Foundry

and shall conform to all applicable plumbing, and building requirements. Buried pipe shall be installed

inaccordancewithASTMD2321andASTMF1668.Solventcementjointsshallbemadeinatwostep

processwithprimerconformingtoASTMF656andsolventcementconformingtoASTMD2564.The

pipeshallbeprotectedfromchemicalagents,plasticizedvinylproducts,orotheraggressivechemical

agents not compatible with PVC compounds. Systems shall be hydrostatically tested after installation.

WARNING! Nevertestwithortransport/storecompressedairorgasinPVCpipeorttings.

Referenced Standards*:

 ASTMD1784 RigidVinylCompounds

 ASTMD3034 PVCGravitySewerPipe(SDR)35PS46

 ASTMD2855 JointsForSewerPipeUsingSolventCement

 ASTMD2564 SolventCementsForPVCSewerPipe

 ASTMD2321 UndergroundInstallationofThermoplasticPipe(non-pressureapplications)

 ASTMF477 ElastomericSeals(Gaskets)ForJoiningPlasticPipe

 ASTMF656 PrimersforPVCPipeandFittings

 ASTMF1668 ProceduresforBuriedPlasticPipe

*Note:Latestrevisionofeachstandardapplies.

Short Speciﬁcation:

 PipeshallbemanufacturedfromPVCcompoundwithacellclassof12364asperASTMD1784.PVC

SDR35PSMpipeshallconformtoASTMD3034forgasketorsolventweldpipewithaminimumpipe

stiffness of 46. Pipe shall be plastic sewer main outside diameter with a standard dimension ratio (SDR)

of35.GasketsshallconformtoASTMF477.

 Allpipeshallbeproducedbyasinglemanufacturerandshallbeinstalledinaccordancewithmanufacturer’s

recommendations and applicable code requirements. Buried pipe shall be installed in accordance with

ASTMD2321andASTMF1668.SolventcementsshallconformtoASTMD2564,primershallconform

toASTMF656.PipeistobemanufacturedbyCharlottePipeandFoundryCompanyandisintendedfor

non-pressure gravity sewer and surface water applications.

GENERAL INFORMATION

20

Plastics Technical Manual

GENERAL INFORMATION

System: PVC D 2729 Sewer and Drain Pipe

Scope: This speciﬁcation covers PVC D 2729 Sewer Pipe for drainage applications. This pipe is intended for

drainage applications where the operating temperature will not exceed 140°F.

Speciﬁcation: Pipe shall be manufactured from virgin rigid PVC (polyvinyl chloride) vinyl compounds with a Cell Class

of12454asidentiedinASTMD1784.

 PVCD2729SewerPipedimensionsandphysicalpropertiesshallconformtoASTMD2729.Allpipe

shallbemanufacturedintheUnitedStates.

Installation shall comply with the latest installation instructions published by Charlotte Pipe and Found-

ry and shall conform to all applicable plumbing, building, and ﬁre code requirements. Buried pipe shall

beinstalledinaccordancewithASTMD2321andASTMF1668.Solventcementjointsshallbemade

inatwostepprocesswithprimerconformingtoASTMF656andsolventcementconformingtoASTM

D 2564. The system shall be protected from chemical agents, ﬁre stopping materials, thread sealant,

plasticizedvinyl products, orotheraggressivechemicalagents notcompatiblewithPVCcompounds.

Systemsshallbehydrostaticallytestedafterinstallation.WARNING!Nevertestwithortransport/store

compressed air or gas in PVC pipe or ﬁttings.

Referenced Standards*:

 ASTMD1784 RigidVinylCompounds

 ASTMD2729 PVCSewerPipe

 ASTMD2564 SolventCementsforPVCPipeandFittings

 ASTMF656 PrimerforPVCPipeandFittings

 ASTMD2321 UndergroundInstallationofThermoplasticPipe(non-pressureapplications)

 ASTMF656 PrimersforPVCPipeandFittings

 ASTMF1668 ProceduresforBuriedPlasticPipe

 *Note:Latestrevisionofeachstandardapplies.

 3” PVC30030 10903 Solid 3.250 0.070 810 52.8

 3” PVC30030P 11814 Perforated 3.250 0.070 810 52.8

 4” PVC30040 10905 Solid 4.215 0.075 500 70.4

 4” PVC30040P 11815 Perforated 4.215 0.075 500 70.4

PVC Sewer and Drain ASTM D 2729

Nominal UPC O.D. Min. Wall Wt/100’

Size Part No. 611942- Type (In.) (In.) Ft/Skid (Lbs.)

Short Speciﬁcation:

 PipeshallbemanufacturedfromPVCcompoundwithacellclassof12454perASTMD1784.Pipe

dimensionsandphysicalpropertiesshallconformtoASTMD2729.

 Allpipetobeproducedbyasinglemanufacturerandtobeinstalledinaccordancewithmanufacturer’s

recommendations and all applicable code requirements. Solvent cements shall conform to ASTM D

2564,primershallconform to ASTMF656.ThepipeistobemanufacturedbyCharlottePipeand

Foundry Company and is intended for drainage applications where the temperature will not exceed

140°F.

Perforation Detail

2-Hole 120 Degree

Product Speciﬁcations

Page is loading ...

Charlotte Pipe CTS 12010 0500 User manual

Charlotte Pipe CTS 12010 0500 User manual

Related papers

Other documents