Mettler Toledo SevenCompact S210 Reference guide

Brand: Mettler Toledo

Model: SevenCompact S210

Category: Measuring, testing & control

Type: Reference guide

This manual is also suitable for

SevenCompact™ S210

SevenCompact™ S210

pH Meter

Reference Manual

30459001A4/23/2018 5:15 PM- Schema ST4 PDF engine -Layout by Victor Mahler

SevenCompact™ S210

Table of Contents

1 Introduction 3

2 Safety information 4

2.1 Definitions of signal words and warning symbols ............................................................ 4

2.2 Product specific safety notes ......................................................................................... 4

3 Design and Function 6

3.1 Overview..................................................................................................................... 6

3.2 Rear panel connections ................................................................................................ 6

3.3 Display and icons........................................................................................................ 8

3.4 Key controls................................................................................................................ 9

3.5 Softkeys...................................................................................................................... 9

3.6 Alphanumeric keypad................................................................................................... 10

3.6.1 Entering alphanumeric characters ................................................................... 10

3.6.2 Editing values in tables.................................................................................. 10

3.7 Navigating within a menu............................................................................................. 11

3.8 Navigating between menus........................................................................................... 11

3.9 Endpoint types............................................................................................................. 11

4 Putting into Operation 12

4.1 Scope of delivery ......................................................................................................... 12

4.2 Mounting uPlace™ electrode arm.................................................................................. 12

4.3 Installing power supply................................................................................................. 13

4.4 Connecting sensors...................................................................................................... 14

4.5 Switching the instrument on and off ............................................................................... 14

4.6 Connectivity ................................................................................................................ 14

5 Configuring the Instrument 16

5.1 Sample ID................................................................................................................... 16

5.2 User ID ....................................................................................................................... 16

5.3 Stirrer ......................................................................................................................... 17

5.4 Data storage ............................................................................................................... 17

5.5 System settings ........................................................................................................... 18

5.5.1 Language..................................................................................................... 18

5.5.2 Time and Date .............................................................................................. 18

5.5.3 Access Control.............................................................................................. 18

5.5.4 Audio signal ................................................................................................. 18

5.5.5 Operator mode.............................................................................................. 19

5.5.6 Screen settings ............................................................................................. 19

5.6 Service ....................................................................................................................... 19

5.7 Instrument Self-test....................................................................................................... 20

6 Measuring pH 21

6.1 Measurement settings................................................................................................... 21

6.1.1 Sensor ID / SN .............................................................................................. 21

6.1.2 Calibration Settings ....................................................................................... 22

6.1.3 Measurement Settings.................................................................................... 22

6.1.4 Endpoint Type............................................................................................... 23

6.1.5 Temperature Settings ..................................................................................... 23

6.1.6 Measurement Limits ...................................................................................... 24

6.2 Sensor Calibration........................................................................................................ 24

6.2.1 Running a one-point pH calibration................................................................. 24

6.2.2 Running a multi-point pH calibration ............................................................... 24

6.3 Sample Measurement................................................................................................... 25

Table of Contents 1SevenCompact™ S210

7 Managing data 26

7.1 Measurement data ....................................................................................................... 26

7.2 Calibration data........................................................................................................... 26

7.3 ISM data..................................................................................................................... 27

7.4 Transfer Interfaces........................................................................................................ 28

8 Maintenance and Care 29

8.1 Cleaning the Instrument................................................................................................ 29

8.2 Maintenance of electrodes............................................................................................. 29

8.3 Transporting the instrument........................................................................................... 30

8.4 Disposal..................................................................................................................... 30

9 Troubleshooting 31

9.1 Instrument messages ................................................................................................... 31

9.2 Error limits .................................................................................................................. 33

10 Sensors, Solutions and Accessories 34

11 Technical Data 36

12 Appendix 38

12.1 Buffers........................................................................................................................ 38

Table of Contents2 SevenCompact™ S210

Introduction 3SevenCompact™ S210

1 Introduction

Thank you for choosing a METTLER TOLEDO SevenCompact™ S210. The SevenCompact™ S210 is an easy-

to-operate instrument for measuring pH.

About this document

The instructions in this document refer to a pH meter running firmware version 2.01.03 or higher.

If you have any additional questions, contact your authorized METTLER TOLEDO dealer or service represen-

tative.

u www.mt.com/contact

Conventions and symbols

Refers to an external document.

Note

for useful information about the product.

Elements of instructions

Prerequisites

1 Steps

2 ...

ð Intermediate results

ð Results

Safety information4 SevenCompact™ S210

2 Safety information

• This Reference Manual contains a full description of the instrument and its use.

• Keep the Reference Manual for future reference.

• Include the Reference Manual if you transfer the instrument to other parties.

Only use the instrument according to the Reference Manual. If you do not use the instrument according to the

Reference Manual or if it is modified, the safety of the instrument may be impaired and Mettler-Toledo GmbH

assumes no liability.

2.1 Definitions of signal words and warning symbols

Safety notes contain important information on safety issues. Ignoring the safety notes may lead to personal

injury, damage to the instrument, malfunctions and false results. Safety notes are marked with the following

signal words and warning symbols:

Signal words

WARNING

A hazardous situation with medium risk, possibly resulting in death or severe injury if

not avoided.

NOTICE

A hazardous situation with low risk, resulting in damage to the instrument, other

material damage, malfunctions and erroneous results, or loss of data.

Warning symbols

Electrical shock

2.2 Product specific safety notes

Intended use

This instrument is designed to be used by trained staff. The SevenCompact™ S210 is intended for measuring

pH.

Any other type of use and operation beyond the limits of use stated by Mettler-Toledo GmbH without consent

from Mettler-Toledo GmbH is considered as not intended.

Responsibilities of the instrument owner

The instrument owner is the person holding the legal title to the instrument and who uses the instrument or

authorizes any person to use it, or the person who is deemed by law to be the operator of the instrument. The

instrument owner is responsible for the safety of all users of the instrument and third parties.

METTLER TOLEDO assumes that the instrument owner trains users to safely use the instrument in their

workplace and deal with potential hazards. METTLER TOLEDO assumes that the instrument owner provides the

necessary protective gear.

Safety notes

WARNING

Danger of death or serious injury due to electric shock!

Contact with parts that carry a live current can lead to death or injury.

1 Only use the METTLER TOLEDO AC adapter designed for your instrument.

2 Keep all electrical cables and connections away from liquids and moisture.

3 Check the cables and the plugs for damage and replace damaged cables and plugs.

Safety information 5SevenCompact™ S210

NOTICE

Risk of damage to the instrument due to the use of unsuitable parts!

Using unsuitable parts with the instrument can damage the instrument or cause it to

malfunction.

− Only use parts from METTLER TOLEDO that are intended to be used with your instrument.

FCC Rules

This device complies with Part 15 of the FCC Rules and Radio Interference Requirements of the Canadian

Department of Communications. Operation is subject to the following conditions: (1) this device may not cause

harmful interference, and (2) this device must accept any interference received, including interference that may

cause undesired operation.

This equipment has been tested and found to comply with the limits for a Class A digital device, pursuant to

Part 15 of the FCC rules. These limits are designed to provide reasonable protection against harmful inter-

ference when the equipment is operated in a commercial environment. This equipment generates, uses, and

can radiate radio frequency energy and, if not installed and used in accordance with the instruction manual,

may cause harmful interference to radio communications. Operation of this equipment in a residential area is

likely to cause harmful interference in which case the user will be required to correct the interference at his own

expense.

Design and Function6 SevenCompact™ S210

3 Design and Function

3.1 Overview

Number Key Press and release Press and hold for 2

seconds

Switch meter on Switch meter off

Display

Softkeys The function of the softkeys varies from screen to

screen

• Start or end

measurement

(measurement screen)

• Confirm input or start

editing a table

• Exit menu and go back

to measurement screen

Switch between

measurement close-up

screen and full-information

screen

Start calibration Review the last calibration

data

3.2 Rear panel connections

Reference socket for reference electrodes

RS232 interface

DC power supply socket

BNC socket for mV/pH signal input

RCA (Cinch) socket for temperature signal

input

Mini DIN socket for METTLER TOLEDO stirrer

USB B interface

USB A interface

Design and Function 7SevenCompact™ S210

PIN assignment for the RS-232 interface. METTLER TOLEDO printers such as RS-P25 can be connected to this

interface.

Design and Function8 SevenCompact™ S210

3.3 Display and icons

There are two modes available for the display representation: the full-information screen with all the information

displayed, and the measurement close-up screen uFocus™, where the measurement information is shown in

large font. To toggle between these views, press and hold Read during, after or before a measurement.

Standard view

Data Channel Menu Mode

24-06-2017

10:34

InLab 742

uFocus™ view

Data Channel Menu Mode

24-06-2017

10:34

InLab 742

Data

Mode

24-06-2018

10:34

14 15

Icon Description

1 Stirrer icon (appears when stirring is active)

2 7.000 pH

Measurement value and used measurement unit

3 24-06-2018

10:34

Date and time

4 25°C

Measurement temperature

5 MTC Temperature Correction

ATC: Temperature sensor connected

MTC: no temperature sensor connected or detected

6 Stability Criterion

Strict

Standard

Fast

7 Endpoint Type

A: Auto; measurement stops automatically when the signal is stable

M: Manual; to manually stop the measurement

T: Timed; the measurement stops after the preset time

Stability Signal appears if the signal is stable

8 User ID

9 M

Number of data sets in memory

10 Sensor ID

11 Sample ID

Buffer groups or standards

Design and Function 9SevenCompact™ S210

Icon Description

13 ISM

sensor connected

Softkeys are buttons whose function changes depending on the context.

See [Softkeys}Page9]

3.4 Key controls

Key Press and release Press and hold for 2 seconds

Switch meter on Switch meter off

• Start or end measurement

(measurement screen)

• Confirm input or start editing a table

• Exit menu and go back to measurement

screen

Switch between measurement close-up

screen and full-information screen

Start calibration Review the last calibration data

Softkeys

The function of the softkeys varies from

screen to screen

3.5 Softkeys

The meter has four softkeys. The functions assigned to them change during operation depending on the appli-

cation. The assignment is shown on the bottom line of the screen.

Data

Access data menu

Mode

Change measurement mode

Press and hold to change the channel

selection

Access meter settings

Move one position to the right Increase value

Move one position to the left Decrease value

Scroll up in the menu Scroll to next page of results

Scroll down in the menu

Calculate

Calculate the calibration values

Edit

Edit table or value

Select

Select the highlighted function or setting

Delete

Delete selected data

Start

Start the measurement

Save

Save data, setting or value

Interface

Choose the transfer interface.

Yes

Confirm an entry

Transfer

Transfer selected data

Reject an entry

Design and Function10 SevenCompact™ S210

3.6 Alphanumeric keypad

3.6.1 Entering alphanumeric characters

The meter has a screen keypad for entering IDs, SNs and PINs. Both numbers and letters are allowed for these

entries. When entering a PIN, each character entered will be displayed as ( * ).

Enter Sample ID

Exit

Press 'Read' to confirm

1 Move the cursor position using the , or keys.

2 Press Read to confirm an entry.

ð The position of the next character that is entered is blinking.

3 Repeat these steps to enter additional characters.

- or -

To delete an entry, select the character. Navigate to Delete and press Read.

4 To confirm and save the entries, navigate to OK and press Read.

- or -

To reject the entries, press Exit.

Entering IDs / PIN

The four softkeys and the Read key are used for navigating on the keypad and entering the ID/PIN.

Example text: WATER

1 If 1 is highlighted, press once.

ð Q is highlighted.

2 Press once.

ð W is highlighted.

3 Press Read to enter W.

4 Reposition the selection to A, T, E and R, confirm each selection with Read.

5 Reposition the selection to OK, and press Read to save the ID.

Note

• Instead of entering an ID with the alphanumeric keypad, you can also use a USB-keyboard or a USB-

barcode scanner. In case a character is entered or scanned that is not available on the instrument

keyboard, the entry will be displayed as an underscore (_).

3.6.2 Editing values in tables

The meter allows you to enter, edit or remove values in tables. (for example, temperature and buffer values for

a customized buffer group). This is accomplished by using the softkeys to navigate from cell to cell.

1 Press Read to start editing the cell in the table.

ð The softkeys on the display change.

2 Press and to enter the value and press Read to confirm.

ð The softkeys change back to and .

3 Navigate to a cell and press Delete to remove a value.

4 To finish editing the table, navigate with the and to highlight Save.

5 Press Read to confirm the action and exit the menu.

Design and Function 11SevenCompact™ S210

3.7 Navigating within a menu

1 Press Menu to enter the settings.

2 Move the selection to a menu item using the or keys and press Select to open the selection.

3 Apply the required settings using the navigation keys.

- or -

If applicable, move the selection to the next menu item in the hierarchy using the or keys.

4 Press Exit to return to the previous menu screen, or press Read to return to the measurement screen

directly.

3.8 Navigating between menus

The meter display consists of a measurement frame, softkeys, areas for status icons and underlying menu

areas. To access the menu areas and to navigate between them, use the softkeys.

1 Press Menu to enter the settings.

2 Move the selection to the top of the screen to select the tab using the or keys.

ð The navigation keys to navigate left and right are shown.

3 Move the selection to chose another tab using the or keys.

4 Press Exit to return to the measurement screen.

3.9 Endpoint types

A general setting that defines how the endpoint of the measurement is to be determined.

Automatic

Endpoint

Manual

Endpoint

Timed

Endpoint

Measurement stopped after time,

reading was stable

Measurement stopped after time,

reading was not stable

Measurement stopped manually,

reading was not stable

Measurement stopped manually,

reading was stable

Measurement stopped automatically,

reading was stable

Blinking letter

Defined measurement time elapsed

User presses Read

Signal becomes stable

Putting into Operation12 SevenCompact™ S210

4 Putting into Operation

4.1 Scope of delivery

Unpack the instrument and check the scope of delivery. Keep the calibration certificate in a safe place. Seven-

Compact™ is delivered with:

• uPlace™ electrode arm

• Sensors (kit version only)

• Universal AC adapter

• Transparent protective cover

• CD-ROM with Reference Manual and User Manual (English, German, French, Italian, Spanish, Portuguese,

Polish, Russian, Chinese, Japanese Korean, Thai)

• User Manual (print version, English, German, French, Italian, Spanish, Portuguese, Polish)

• Declaration of conformity

• Calibration certificate

4.2 Mounting uPlace™ electrode arm

The electrode arm can be used as stand alone or it

can be attached to the instrument on the left or right

side, according to your preferences. The height of the

electrode arm can be varied by using the extension

shaft part. Use the wrench to attach the extension

part .

Assembly of the electrode arm

1 Use the wrench to attach the base to the electrode

arm by tightening the screws. The electrode arm

can now be used in the stand alone mode.

Putting into Operation 13SevenCompact™ S210

2 Then insert the foot of the meter to the arm base

and shift the meter in the direction of the arrow to

make the foot fit.

3 Use the lock screw to attach the meter to the base

of the arm.

4.3 Installing power supply

WARNING

Danger of death or serious injury due to electric shock!

Contact with parts that carry a live current can lead to death or injury.

1 Only use the METTLER TOLEDO AC adapter designed for your instrument.

2 Keep all electrical cables and connections away from liquids and moisture.

3 Check the cables and the plugs for damage and replace damaged cables and plugs.

NOTICE

Danger of damage to the AC adapter due to overheating!

If the AC adapter is covered or in a container, it is not sufficiently cooled and overheats.

1 Do not cover the AC adapter.

2 Do not put the AC adapter in a container.

The instrument is operated using an AC adapter. The AC adapter is suitable for all supply line voltages ranging

from 100...240 V AC ±10% and 50-60 Hz.

PUSH

1 Insert the correct connector plug into the AC adapter

until it is completely inserted.

2 Connect the cable of the AC adapter with the DC socket

of the instrument.

3 Install the cables in such a way that they cannot be

damaged or interfere with operation.

Putting into Operation14 SevenCompact™ S210

4 Insert the plug of the AC adapter in a power outlet that is easily accessible.

ð To remove the connector plug, push the release button and withdraw the connector plug.

4.4 Connecting sensors

When connecting a sensor, make sure that the plugs are properly inserted. If you are using a sensor with a

built-in temperature probe or a separate temperature probe, connect the second cable to the ATC socket.

Example

− Connect a pH sensor to the BNC plug and if a temperature probe is integrated, connect the RCA (chinch)

plug to the ATC input.

- or -

Connect a conductivity probe to the conductivity input, a temperature probe is always built in and does not

need to be connected seperatly. If you have a digital sensor connect it to the digital input.

ISM

sensor

When connecting an ISM

sensor to the meter, one of the following conditions have to be met for the calibration

data to be transferred automatically from the chip of the sensor into the meter and is used for further

measurements. After attaching the ISM

sensor ...

• The meter must be switched on.

• (If the meter is already switched on) the Read key is pressed.

• (If the meter is already switched on) the Cal key is pressed.

We strongly recommend you to switch off the meter when disconnecting an ISM sensor. In doing so, you make

sure that the sensor is not removed while the instrument is reading data from or writing data to the ISM-chip of

the sensor.

The ISM icon appears on the display and the sensor ID of the sensor chip is registered and appears on the

display.

The calibration history, the initial certificate and the maximum temperature can be reviewed and printed in the

data memory.

4.5 Switching the instrument on and off

Switching on

− Press and release On/Off to switch on the instrument.

ð The firmware version, the serial number and the current date are displayed for a few seconds. After that

the instrument is ready for use.

Switching off

− Press and hold the On/Off key until the instrument switches to standby mode.

Note

• In the standby mode, the control circuit for the On/Off switch is energized. The rest of the instrument is no

longer energized.

4.6 Connectivity

Thanks to the plug & play capability, USB-sticks, barcode reader and printers are detected automatically.

Connection Use

RS232 interface RS-Printers

USB B interface

EasyDirect pH PC Software

USB A interface USB-printer, USB barcode reader

USB-stick with file format FAT12/FAT16/FAT32

The instrument adjusts the baud rate to the following settings in case no automatic baud rate synchronization

occurs (only with printer types RS-P25, RS-P26, RS-P28):

Putting into Operation 15SevenCompact™ S210

Printer Baud rate: 1200

Data bits: 8

Parity: none

Stop bits: 1

Handshake: none

Configuring the Instrument16 SevenCompact™ S210

5 Configuring the Instrument

Sample ID

System Settings

1. Enter Sample ID 1. Language

2. Auto Sequential 2. Time and Date

3. Select Sample ID 3. Access Control

4. Delete Sample ID 4. Beep

User ID 5. Routine/Expert Mode

1. Enter User ID 6. Screen Settings

2. Select User ID

Service

3. Delete User ID 1. Software Update

Stirrer 2. Export Settings to USB-stick

1. Stir Before Measurement 3. Factory Reset

2. Stir During Measurement

Instrument Self-test

3. Stir Speed

4. Stirrer Voltage Settings

Data Storage

1. Storage Mode

2. Storage Destination

3. Time Interval Readings

4. Printout Format

5.1 Sample ID

Navigation: Menu > > Sample ID

Parameter Description Values

Enter Sample ID Alphanumeric sample ID with up to 16 characters can be entered.

A maximum of 10 sample IDs are stored in memory and listed for

selection. If the maximum number of IDs has been stored, the

meter will display the message Memory is full.

1…16 characters

Auto Sequential

On: Using this setting will automatically increment the sample ID

by 1 for each reading. If the last character of the sample ID is not

a number, then the number 1 will be added to the sample ID with

the second sample. This requires the sample ID to have less than

16 characters.

Off: The sample ID is not incremented automatically.

On | Off

Select Sample ID To select a sample ID out of a list of already entered sample IDs. List of available sample

IDs

Delete Sample ID To delete an existing sample ID out of the list, select the sample

ID you want to delete and press Read.

List of available sample

IDs

5.2 User ID

Navigation: Menu > > User ID

Parameter Description Values

Enter User ID Alphanumeric user IDs with up to 16 characters can be entered. A

maximum of 10 user IDs are stored in memory and listed for

selection. If the maximum number of IDs has been stored, the

meter will display the message Memory is full.

1…16 characters

Select User ID To select a user out of a list of existing users. List of available user IDs

Delete User ID To delete an existing user ID out of the list, select the user ID you

want to delete and press Read.

List of available user IDs

Configuring the Instrument 17SevenCompact™ S210

5.3 Stirrer

You can connect the METTLER TOLEDO external magnetic stirrer to the instrument. This stirrer is powered by the

instrument and will be automatically switched on/off according to the settings.

If a uMix or Compact stirrer is connected to the stirrer output, the option Stir During Measurement or Stir

Before Measurement can be selected. When the stirrer is active, the symbol is displayed.

Navigation: Menu > > Stirrer

Parameter Description Values

Stir Before

Measurement

On: Using this setting will include a stirring period before the

measurement starts (after pressing Read).

Off: No stirring before the measurement will take place.

On | Off

Enter Time

Defines the stir duration [s] if Stir Before Measurement is

activated.

3…60

Stir During

Measurement

On: Using this setting will results in stirring during the

measurement. When the measurement is stopped, the stirrer is

automatically switched off.

Off: No stirring during the measurement will take place.

On | Off

Stir Speed Defines the stir speed in steps, according to preferences and the

characteristics of the sample.

1…5

Stirrer Voltage

Settings

Defines the minimum and maximum voltages for the stirrer.

Stir Speed1: Defines the voltage for the lowest stirring speed.

Stir Speed5: Defines the voltage for the highest stirring speed.

0.5…8.0V

5.4 Data storage

Navigation: Menu > > Data Storage

The meter stores up to 1000 sets of measurement data in the memory. The number of data sets already stored

in the memory is indicated by MXXXX on the display. A message appears on the display when the memory is

full. To save further measurements if the memory is full, data has to be deleted first. You can select between

automatic and manual storage. Press Exit to discard the endpoint readings.

Parameter Description Values

Storage Mode

Automatic Storage: Stores/transfers every found reading to the

memory/interface or both automatically.

Manual Storage: If selected, Save appears on the display as

soon as a measurement has found an endpoint. Press Save to

save or transfer the endpoint readings. The readings can only be

stored once. When the data is stored, Save disappears from the

measurement screen.

Automatic Storage |

Manual Storage

Storage Desti-

nation

Select to transfer the data to the memory, Printer or PC.

Memory: Data will be stored in the internal memory of the

instrument.

Printer: Data will be printed to the connected printer.

PC: Data will be transferred to the connected PC, running

EasyDirect pH.

Memory | Printer | PC

Interval Readings Activates the function to measure at intervals.

The measurement series stops according to the selected endpoint

format or manually by pressing Read.

On | Off

Interval Time Define the time interval between the measurement points in [s] if

Interval Readings is activated.

1…3600

Configuring the Instrument18 SevenCompact™ S210

5.5 System settings

5.5.1 Language

Navigation: Menu > > System Settings > Language

Parameter Description Values

Language Defines the language for operation of the instrument. English | Deutsch |

French | Italian | Spanish

| Portuguese | Russian |

Polish | Chinese |

Korean | Japanese |

Thai | Turkish

5.5.2 Time and Date

Navigation: Menu > > System Settings > Time and Date

When starting the meter for the first time, the display for entering time and date appears automatically.

Parameter Description Values

Time Define the time and the time format for operation of the

instrument.

24-hour format (for example, 06:56 and 18:56)

12-hour format (for example, 06:56 AM and 06:56 PM)

12h| 24h

Time and Date Defines the date and the date format for operation of the

instrument.

Date

28-11-20xx (day-month-year)

11-28-20xx (month-day-year)

28-Nov-20xx (day-month-year)

28/11/20xx (day-month-year)

List of available date

formats

5.5.3 Access Control

Navigation: Menu > > System Settings > Access Control

A maximum of 6 characters can be entered as PIN. In the factory default settings, the PIN for deleting data is

set to 000000 and is activated, no instrument login password is set.

Parameter Description Values

System Settings To enable a PIN protection for the required access control ON.

When selected, the window for entering an alphanumeric PIN

appears.

1…6 characters

Deletion of Data Defines if the deletion of data is PIN protected. On| Off

Instrument Login Defines if the instrument login is PIN protected. On| Off

5.5.4 Audio signal

Navigation: Menu > > System Settings > Beep

Parameter Description Values

Beep Defines if an audio signal should be enabled. Keypress| Alarm

Messages|

Measurement Endpoint

Page is loading ...

Mettler Toledo SevenCompact S210 Reference guide

Brand: Mettler Toledo

Model: SevenCompact S210

Category: Measuring, testing & control

Type: Reference guide

This manual is also suitable for

SevenCompact™ S210

Download PDF

report

Mettler Toledo SevenCompact S210 Reference guide

This manual is also suitable for

Mettler Toledo SevenCompact S210 Reference guide

Related papers

Other documents