Omega OM-SGD-43-A Owner's manual

Brand: Omega

Model: OM-SGD-43-A

Category: Measuring, testing & control

Type: Owner's manual

e-mail: [email protected]

For latest product manuals:

www.omegamanual.info

OM-SGD-43-A

Shop online at

omega.com

User’s Guide

4.3” Multifunction Smart Graphics Display

Specications liable to change without prior warning Data Sheet - Issue 1 SL

www.omega.com

OM-SGD-43-A

4.3” Smart Graphics Display

* For measurement ranges up to ±10V.

** Hardware capability, but not available in soware at launch

Display 4.3” TFT with 262k colours

Touchscreen Capacive

Resoluon 480 x 272px

Processor Freescale i.MX283 (454MHz, 32bit, ARM 9)

Analogue Inputs 4 x ±40V or 4-20mA (16bit ADC with 0.05% ±1mV typical accuracy*)

Serial Buses RS232**, SPI**, I2C**, RS485**, Ethernet**

Memory 1Gbit DDR2 SDRAM and 2GB SD card

Operang Temperature 0 to 40°C (32 to 104°F)

Supply 5 to 30V d.c. (300mA typical at 5V d.c.)

Outside Dimensions 119.3 (4.7) x 79.8 (3.1) x 20.0 (0.8) mm (in)

Speciﬁcations

The OM-SGD-43-A is the rst in a range of PanelPilotACE compable displays and panel meters. The low-prole display

features a 4.3” capacive touch screen and an ARM Cortex A9 processor running embedded Linux. The display can be

powered from either USB or a 5 to 30V d.c. supply and oers users a wealth of hardware interfaces which include four

16bit bi-polar analogue inputs (to a maximum of ±40V d.c.), eight digital input/output pins, two alarm outputs (maximum

current sink 10mA) and four 8bit PWM outputs.

Users program the display using the free PanelPilotACE Design Studio soware which allows the creaon of anything from

simple meters and dials, through to advanced user interfaces with control elements.

OM-SGD-43-A is a 4.3” capacitive touch display designed for use with

PanelPilotACE Design Studio, a free drag-and-drop style software package

for rapid development of advanced user interfaces

and panel meters.

Specications liable to change without prior warning Data Sheet - Issue 1 SL

www.omega.com

OM-SGD-43-A

4.3” Smart Graphics Display

PanelPilotACE Design Studio

Making Industrial User Interface Design Simple

The design soware provides a number of building blocks which allow users to drag-and-drop elements onto the screen

to quickly create advanced user interfaces. From background images to text elements, analogue style meters, touch

screen navigaon elements and even complex logic statements, users can build up mul-screen interfaces without

needing to write a line of code.

There is a library of pre-dened elements such as meters, buons and switches, and users can create their own content

by combining elements or imporng graphics in a number of formats (including jpg, png, f, bmp and gif). The soware

includes support for transparency and mulple layers.

Hardware interfacing is similarly intuive, with hardware elements being dragged into a funcon builder where

associaons with graphical elements (such as a needle on a meter) can be dened. Here users can determine scaling for

analogue inputs, dene alarm triggers, behaviours for digital inputs and outputs and congure PWM outputs.

Previewing and Uploading Projects

The soware includes a ‘Preview in Emulator’ funcon which emulates the hardware’s inputs and outputs, allowing users

to test their projects prior to upload. Projects are uploaded to the OM-SGD-43-A via a mini USB port.

PanelPilotACE Design Studio is compatible with Windows XP (SP3), Vista, 7 and 8 and can be downloaded free

from www.omega.com.

Specications liable to change without prior warning Data Sheet - Issue 1 SL

www.omega.com

PL5

USB

PL4

PL7

PL6

54321

PL11PL8

119.3 (4.7)

115.0 (4.5)

79.8 (3.1)

76.0 (3.0)

2.0 (0.1)

20.0 (0.8)

TBLK1

123456

Dimensions

All dimensions are in mm (in)

OM-SGD-43-A

4.3” Smart Graphics Display

SCALE 1 : 1

Panel Cut-Out and Fitting

The panel cut-out is 117.0 x 78.0mm (4.6” x 3.07”).

There are two mounng methods:

The rst uses clips that protude from the plasc

assembly and is suitable for panels between 1 and

3mm (0.04” and 0.12”) in thickness.

The second method uses a rear mounng plasc

bracket featuring grub screws for a more secure

and adaptable t. This second mounng method is

suitable for panels between 0.5 and 4.0mm (0.01”

and 0.15”) in thickness.

Specications liable to change without prior warning Data Sheet - Issue 1 SL

www.omega.com

Pin Out

OM-SGD-43-A

4.3” Smart Graphics Display

PL4: Alarms, Serial Input and Digital I/O

Pin Number Funcon

1 0V

2 Supply Voltage (V+)

3 Alarm 1 (ALM1)

4 Alarm 2 (ALM2)

5 I2C0 SCL

6 I2C0 SDA

7 SPI SS1

8 SPI MOSI

9 SPI MISO

10 SPI SCK

11 Digital I/O Channel 1 (DIG1)

12 Digital I/O Channel 2 (DIG2)

13 Digital I/O Channel 3 (DIG3)

14 Digital I/O Channel 4 (DIG4)

15 Digital I/O Channel 5 (DIG5)

16 Digital I/O Channel 6 (DIG6)

17 Digital I/O Channel 7 (DIG7)

18 Digital I/O Channel 8 (DIG8)

19 PWM Channel 1 (PWM1)

20 PWM Channel 2 (PWM2)

21 PWM Channel 3 (PWM3)

22 PWM Channel 4 (PWM4)

23 DUART TX (for internal use)

24 DUART RX (for internal use)

25 USB D+

26 USB D-

27 I2C1 SDA (for internal use)

28 I2C1 SCL (for internal use)

29 +5V Output Voltage

30 High Speed ADC

31 +3V3 Output Voltage

32 0V

33 Shorted together to enable

rmware upgrade

TBLK1: Power & Analogue Inputs

Pin Number Funcon

1 Supply Voltage (V+)

2 0V

3 Analogue Input 4 (IN4)

4 Analogue Input 3 (IN3)

5 Analogue Input 2 (IN2)

6 Analogue Input 1 (IN1)

PL5

USB

PL4

PL7

PL6

54321

PL11PL8

TBLK1

123456

1 2

7 8

1 2

7 8

21 22

PL5

USB

PL4

PL7

PL6

54321

PL11PL8

TBLK1

123456

1 2

7 8

1 2

7 8

21 22

Specications liable to change without prior warning Data Sheet - Issue 1 SL

www.omega.com

PL5

USB

PL4

PL7

PL6

54321

PL11PL8

TBLK1

123456

1 2

7 8

1 2

7 8

21 22

OM-SGD-43-A

4.3” Smart Graphics Display

PL5: Programming Interface (JTAG)

Pin Number Funcon

1 +3V3 Output Voltage

2 N/C (no connecon)

3 JTAG_TRST

4 OV

5 JTAG_TDI

6 OV

7 JTAG_TMS

8 OV

9 JTAG_TCK

10 OV

11 JTAG_RTCK

12 OV

13 JTAG_TDO

14 0V

15 n_reset

16 0V

17 N/C

18 0V

19 0V via a 47k Ohms resistor

20 0V

Pin Out (continued...)

PL5

USB

PL4

PL7

PL6

54321

PL11PL8

TBLK1

123456

1 2

7 8

1 2

7 8

21 22

PL6: Ethernet & Expansion I/O

Pin Number Funcon

1 ENT CLK

2 ENT MDC

3 ENT MDIO

4 ENT RXD0

5 ENT RXD1

6 ENT RX EN

7 ENT TXD0

8 ENT TXD1

9 ENT TX EN

10 Digital I/O 9 (expansion)

11 Digital I/O 10 (expansion)

12 Digital I/O 11 (expansion)

13 Digital I/O 12 (expansion)

14 Digital I/O 13 (expansion)

15 Digital I/O 14 (expansion)

16 Digital I/O 15 (expansion)

17 Digital I/O 16 (expansion)

18 Digital I/O 17 (expansion)

19 +5V

20 0V

21 External Module Hardware ID

22 External Module Hardware ID

Specications liable to change without prior warning Data Sheet - Issue 1 SL

www.omega.com

Pin Out (continued...)

OM-SGD-43-A

4.3” Smart Graphics Display

PL5

USB

PL4

PL7

PL6

54321

PL11PL8

TBLK1

123456

1 2

7 8

1 2

7 8

21 22

PL5

USB

PL4

PL7

PL6

54321

PL11PL8

TBLK1

123456

1 2

7 8

1 2

7 8

21 22

PL5

USB

PL4

PL7

PL6

54321

PL11PL8

TBLK1

123456

1 2

7 8

1 2

7 8

21 22

PL11: Analogue Inputs

Pin Number Funcon

1 Analogue Input 1 (IN1)

2 0V

3 Analogue Input 2 (IN2)

4 0V

5 Analogue Input 3 (IN3)

6 0V

7 Analogue Input 4 (IN4)

8 0V

PL8: 4-20mA Current Loop Measurement

Pin Number Funcon

1-2 4-20mA current loop measurement (IN1) when shorted

3-4 4-20mA current loop measurement (IN2) when shorted

5-6 4-20mA current loop measurement (IN3) when shorted

7-8 4-20mA current loop measurement (IN4) when shorted

PL7: RS232 Interface

Pin Number Funcon

1 TX

2 RTS

3 RX

4 CTS

5 0V

Specications liable to change without prior warning Data Sheet - Issue 1 SL

www.omega.com

OM-SGD-43-A

4.3” Smart Graphics Display

SGD 43-A

5 - 30V d.c.

V+

Various Operating Modes

Supply Voltage Screw Terminals (TBLK1) Pin (PL4)

V+ 1 2

0V 2 1

Measuring an Analogue Voltage

An analogue voltage can be connected to either the screw

terminals (TBLK1) or pins (PL11).

Analogue Input Screw Terminals (TBLK1) Pin (PL11)

IN1 6 1

0V 2 2

IN2 5 3

0V 2 4

IN3 4 5

0V 2 6

IN4 3 7

0V 2 8

To minimise osets it is best pracce to connect analogue grounds directly to

the meter pins (PL11) or screw terminals (TBLK1).

The OM-SGD-43-A uses a programmable gain amplier (PGA) together

with a 16-bit analogue to digital converter (ADC) for its analogue voltage

measurements. The PGA is automacally set when the analogue range of a

channel is input into the PanelPilotACE Design Studio.

The table to the right shows the maximum resoluon of the OM-SGD-43-A’s

analogue measurements across a number of voltage ranges.

SGD 43-A

40V d.c.

5 - 30V d.c.

V+

IN1

Supply Voltage

Supply to the display module can be connected to either the

screw terminals (TBLK1), pins (PL4), or the mini-USB connector.

For best results, ensure the power supply is free from

electrical noise.

Analogue Input Resoluon

±1.25V 0.04mV

±2.5V 0.08mV

±5V 0.16mV

±10V 0.33mV

±20V 0.66mV

±40V 1.3mV

OM-SGD-43-A

Specications liable to change without prior warning Data Sheet - Issue 1 SL

www.omega.com

OM-SGD-43-A

4.3” Smart Graphics Display

Driving an Alarm Output

The alarm outputs are open-collector. When an alarm is acve, the output can sink up to 10mA.

Alarm outputs are connected via PL4:

Alarm Output Pin (PL4)

ALM1 3

ALM2 4

Measuring a 4-20mA Current

The 4-20mA signal should be connected as for “Measuring an

Analogue Voltage” but a jumper link should be placed across

pins PL8 for each analogue channel being used:

Analogue Voltage Jumper link (PL8)

IN1 1 & 2

IN2 3 & 4

IN3 5 & 6

IN4 7 & 8

Scaling: The sense resistors used are 110Ω. Therefore in soware scaling 4mA equates to 0.44V and 20mA equates to

2.2V.

Note: transmier terminals (+ or -) must be isolated from the power supply

V+

SGD 43-A

12-30V d.c.

4-20 mA

IN1

PL8

1 2

7 8

Various Operating Modes (continued...)

Driving a relay using alarm outputDriving an LED using alarm output

SGD 43-A

V+

ALM1

10mA

SGD 43-A

ALM1

LED

V+ - VLED

V+

10mA

OM-SGD-43-A

Specications liable to change without prior warning Data Sheet - Issue 1 SL

www.omega.com

OM-SGD-43-A

4.3” Smart Graphics Display

SGD 43-A

DIG1

VDD 3.3V

1kΩ to 10kΩ

Using Digital Input/Output Pins

Digital inputs/outputs are connected via PL4:

Various Operating Modes (continued...)

Digital I/O Pin (PL4)

DIG1 11

DIG2 12

DIG3 13

DIG4 14

DIG5 15

DIG6 16

DIG7 17

DIG8 18

The characteriscs of the digital I/O pins are as follows:

Parameter Min Max Unit

Input voltage (high) 2 3.3 V

Input voltage (low) 0 0.8 V

Output voltage (high) 2.6 3.3 V

Output voltage (low) 0 0.4 V

Output source current -11.4 - mA

Output sink current 9.0 - mA

Generang a digital input with a push buon

OM-SGD-43-A

Specications liable to change without prior warning Data Sheet - Issue 1 SL

www.omega.com

OM-SGD-43-A

4.3” Smart Graphics Display

Various Operating Modes (continued...)

SGD 43-A

PWM

SGD 43-A

PWM

Using PWM output to convert digital to analogue Using PWM output to drive a buzzer

PWM Output Pin (PL4)

PWM1 19

PWM2 20

PWM3 21

PWM4 22

Using PWM Output

If the OM-SGD-43-A is congured to have PWM output, it can be used to drive a buzzer or produce a simple digital-to-

analogue converter.

The PWM outputs are connected via PL4:

The characteriscs of the PWM output pins are as follows:

Parameter Min Max Unit

Voltage 0 3.3 V

Output source current (PWM) -9.5 - mA

Output sink current (PWM) 7.7 - mA

OM-SGD-43-AOM-SGD-43-A

OMEGA’s policy is to make running changes, not model changes, whenever an improvement is possible. This affords

our customers the latest in technology and engineering.

OMEGA is a registered trademark of OMEGA ENGINEERING, INC.

reproduced, translated, or reduced to any electronic medium or machine-readable form, in whole or in part, without the

prior written consent of OMEGA ENGINEERING, INC.

FOR WARRANTY RETURNS, please have the

following information available BEFORE

contacting OMEGA:

1. Purchase Order number under which the product

was PURCHASED,

2. Model and serial number of the product under

warranty, and

3. Repair instructions and/or specific problems

relative to the product.

FOR NON-WARRANTY REPAIRS,

consult OMEGA

for current repair charges. Have the following

information available BEFORE contacting OMEGA:

1. Purchase Order number to cover the COST

of the repair,

2. Model and serial number of the product, and

3. Repair instructions and/or specific problems

relative to the product.

RETURN REQUESTS/INQUIRIES

Direct all warranty and repair requests/inquiries to the OMEGA Customer Service Department.

BEFORE RETURNING ANY PRODUCT(S) TO OMEGA, PURCHASER MUST OBTAIN AN AUTHORIZED

RETURN (AR) NUMBER FROM OMEGA’S CUSTOMER SERVICE DEPARTMENT (IN ORDER TO AVOID

PROCESSING DELAYS). The assigned AR number should then be marked on the outside of the return

package and on any correspondence.

The purchaser is responsible for shipping charges, freight, insurance and proper packaging to prevent

breakage in transit.

WARRANTY/DISCLAIMER

OMEGA ENGINEERING, INC. warrants this unit to be free of defects in materials and workmanship for a

period of 13 months from date of purchase. OMEGA’s WARRANTY adds an additional one (1) month

grace period to the normal one (1) year product warranty to cover handling and shipping time. This

ensures that OMEGA’s customers receive maximum coverage on each product.

If the unit malfunctions, it must be returned to the factory for evaluation. OMEGA’s Customer Service

Department will issue an Authorized Return (AR) number immediately upon phone or written request.

Upon examination by OMEGA, if the unit is found to be defective, it will be repaired or replaced at no

charge. OMEGA’s WARRANTY does not apply to defects resulting from any action of the purchaser,

including but not limited to mishandling, improper interfacing, operation outside of design limits,

improper repair, or unauthorized modification. This WARRANTY is VOID if the unit shows evidence of

having been tampered with or shows evidence of having been damaged as a result of excessive corrosion;

or current, heat, moisture or vibration; improper specification; misapplication; misuse or other operating

conditions outside of OMEGA’s control. Components in which wear is not warranted, include but are not

limited to contact points, fuses, and triacs.

OMEGA is pleased to offer suggestions on the use of its various products. However,

OMEGA neither assumes responsibility for any omissions or errors nor assumes liability for

any damages that result from the use of its products in accordance with information provided

by OMEGA, either verbal or written. OMEGA warrants only that the parts manufactured by the

company will be as specified and free of defects. OMEGA MAKES NO OTHER WARRANTIES OR

REPRESENTATIONS OF ANY KIND WHATSOEVER, EXPRESSED OR IMPLIED, EXCEPT THAT OF

TITLE, AND ALL IMPLIED WARRANTIES INCLUDING ANY WARRANTY OF MERCHANTABILITY

AND FITNESS FOR A PARTICULAR PURPOSE ARE HEREBY DISCLAIMED. LIMITATION OF

LIABILITY: The remedies of purchaser set forth herein are exclusive, and the total liability of

OMEGA with respect to this order, whether based on contract, warranty, negligence,

indemnification, strict liability or otherwise, shall not exceed the purchase price of the

component upon which liability is based. In no event shall OMEGA be liable for

consequential, incidental or special damages.

CONDITIONS: Equipment sold by OMEGA is not intended to be used, nor shall it be used: (1) as a “Basic

Component” under 10 CFR 21 (NRC), used in or with any nuclear installation or activity; or (2) in medical

applications or used on humans. Should any Product(s) be used in or with any nuclear installation or

activity, medical application, used on humans, or misused in any way, OMEGA assumes no responsibility

as set forth in our basic WARRANTY/DISCLAIMER language, and, additionally, purchaser will indemnify

OMEGA and hold OMEGA harmless from any liability or damage whatsoever arising out of the use of the

Product(s) in such a manner.

M5535/0116

Where Do I Find Everything I Need for

Process Measurement and Control?

OMEGA…Of Course!

Shop online at omega.com

TEMPERATURE

Thermocouple, RTD & Thermistor Probes, Connectors, Panels & Assemblies

Wire: Thermocouple, RTD & Thermistor

Calibrators & Ice Point References

Recorders, Controllers & Process Monitors

Infrared Pyrometers

PRESSURE, STRAIN AND FORCE

Transducers & Strain Gages

Load Cells & Pressure Gages

Displacement Transducers

Instrumentation & Accessories

FLOW/LEVEL

Rotameters, Gas Mass Flowmeters & Flow Computers

Air Velocity Indicators

Turbine/Paddlewheel Systems

Totalizers & Batch Controllers

pH/CONDUCTIVITY

pH Electrodes, Testers & Accessories

Benchtop/Laboratory Meters

Controllers, Calibrators, Simulators & Pumps

Industrial pH & Conductivity Equipment

DATA ACQUISITION

Data Acquisition & Engineering Software

Communications-Based Acquisition Systems

Plug-in Cards for Apple, IBM & Compatibles

Data Logging Systems

Recorders, Printers & Plotters

HEATERS

Heating Cable

Cartridge & Strip Heaters

Immersion & Band Heaters

Flexible Heaters

Laboratory Heaters

ENVIRONMENTAL

MONITORING AND CONTROL

Metering & Control Instrumentation

Refractometers

Pumps & Tubing

Air, Soil & Water Monitors

Industrial Water & Wastewater Treatment

pH, Conductivity & Dissolved Oxygen Instruments

Omega OM-SGD-43-A Owner's manual

Brand: Omega

Model: OM-SGD-43-A

Category: Measuring, testing & control

Type: Owner's manual

Download PDF

report

Omega OM-SGD-43-A Owner's manual

Omega OM-SGD-43-A Owner's manual

Related papers

Other documents