Ferm B.V. • P.O. Box 134 • 8280 AC Genemuiden • NL • www.ferm.com 0210/23
UK Subject to change
Document Ref:
FAG-115N/17899/PMR4/issue 1/Mar 02
Copyright ©
These instructions are the sole property of Ferm-Omega Tools and may not be reproduced
Ferm Angle Grinder
FAG-115N
USER’S MANUAL
Art.nr. 719540
Screwfix art.nr 17899
Ferm 7
EXPLODED VIEW
2 Ferm
FERM FAG-115N
ANGLE GRINDER 115 MM
USERS MANUAL
TECHNICAL SPECIFICATIONS
PACKAGE CONTENTS
The package contains:
1 Angle grinder
1 Side handle
1 Spanner
1 Set carbon brushes
1 Instruction manual
1 Guarantee card
Check the machine, loose parts and accessories for
transport damage.
PRODUCT INFORMATION
1. On/off switch
2. Guard
3. Side handle
4. Grinding disc
5. Spindle lock
SAFETY INSTRUCTIONS
The following pictogram is used in these instructions for use:
Denotes risk of personal injury, loss of life or
damage to the tool in case of non-observance of the
instructions in this manual.
Carefully read this manual before using the machine.
Make sure that you know how the machine functions and
how to operate it. Maintain the machine in accordance
with the instructions to make sure it functions properly.
Keep this manual and the enclosed documentation with
the machine.
Ferm products are manufactured to high quality stan-
dards they are safe and fit for purpose at time of sale, but
all tools can be dangerous if the correct precautions are
not taken. Always follow these instructions, do not carry
out the operation until you are sure you can do so in saf-
ety. Remember to consider the work environment for
safe operation as well as safety for tool use.
Warning! When using electric tools, basic safety
precautions should always be followed to reduce
the risk of fire, electric shock and personal injury. Read all
these instructions before attempting to operate this product.
Save these instructions for future reference.
PERSONAL SAFETY
Use Personal Protection Safety Equipment
Protect eyes with safety glasses or goggles note: the use
of safety protective eyewear without the CE mark can
lead to serious injury if the lens breaks. A suitable dust
mask should be worn if cutting; drilling or sanding is
dusty, in particular chipboard or MDF. Approved safety
footwear and headgear should worn as appropriate, for
example on building works or when heavy weights are
involved. Wear suitable gloves and apron to protect
against sparks/debris. Wear earplugs or ear defenders.
Dress properly
Do not wear loose clothing or jewellery. It can get caught
in moving parts. Non-skid footwear is recommended
when working out doors. Wear protective hair covering
to contain long hair
Stay alert
Watch what you are doing Use common sense. Do not
operate tools when tired or after taking alcohol or pre-
scription/ non-prescription drugs.
Voltage | 230 V
Frequency | 50 Hz
Power input | 710 W
No-load speed | 11000/min
Disc diameter | 115 mm
Spindle dimension | M14
Weight | 2.2 kg
Lpa (sound pressure) | 89.6 dB(A)
Lwa (acoustic power) | 102.6 dB(A)
Vibration value | 1.9 m/s2
6 Ferm
SPARE PARTS LIST FAG-115N
REF NR DESCRIPTION FERM NR
6 PINION GEAR 406058
11 ARMATURE 406059
18 SIDE HANDLE 406274
23 SPINDLE GEAR 406066
31 PROTECTING COVER 406718
33 FLANGE INSIDE 406846
35 FLANGE OUTSIDE 406847
37 STATOR 406060
39 CARBON BRUSH 406061
40 CARBON BRUSH HOLDER 406062
43 SWITCH 406063
45 SLIDE SWITCH KNOB 406064
48 SWITCH DRAW BAR 406065
55 WRENCH 406814
Ferm 3
OPERATIONAL SAFETY
Warning! Never use the machine for grinding mag-
nesium workpieces. Use fibre reinforced discs only.
Do not use near flammable materials or people.
Do not use the machine to grind/cut deeper than the maxi-
mum grinding depth of the disc.
Do not use grinding discs for deburring.
Concentrate
Routine and repetition can lead to mistakes. Remember
that a slight lack of concentration can result in serious
injuries in a split second
Keep work area clean
Cluttered areas and benches invite injuries
Consider the work environment Do not expose power
tools to rain or use them in damp or wet locations. Keep
work area well lit. Do not use power tools in the pre-
sence of flammable liquids, vapours or gases.
Guard against electric shock
This unit contains dangerous voltages. Use a RCD (resi-
dual current device) to provide protection against elec-
trical shock. Prevent body contact with grounded sur-
faces (e.g. pipes, radiator, ranges or refrigerators)
Keep children and pets away
Do not let children or pets come into contact with the
tool, extension cable or work area.
Do not force the tool It will work better and safer at the
rate for which it was intended
Use the right tool
Do not force small tools or attachments to do the job of a
heavy-duty tool. Do not use tools for purposes for which
they were not intended; for example do not use a circular
saw for cutting trees or logs
Do not abuse cable
Never carry the tool by the cable or pull it to disconnect
it from the power socket. Keep the cable away from heat,
oil and sharp edges. Do not touch the metal plug pins
when connecting or removing the plug.
Secure Work
Use clamps or a vice to hold work. It is safer than using
your hand and it frees both hands to operate the tool
Do not over-reach
Keep a proper footing and balance at all times
Disconnect tools from power supply
When not in use, before servicing and when changing
accessories such as blades, bits and cutters.
Always switch off and unplug the angle grinder
from the power supply before making adjustments
or changing grinding discs.
Remove adjusting keys and wrenches
Ensure that they are removed from the tool before swit-
ching on.
Avoid unintentional starting
Do not carry plugged in tools with your finger on the
switch. Check that the switch is off before plugging in to
socket.
Extension cables
Use only three core earthed extension cables suitable
for the power input of the tool (minimum cable size
1.5mm2). Plug into an earthed socket only.
When using a cable reel unwind it fully. Do not use long
extension cables.
Outdoors use
If the tool is suitable to be used outdoors, only use an
extension cable intended for outdoor use and marked
accordingly. Use a RCD (residual current device) to pro-
vide protection against electrical shock. Do not use in
rain or damp conditions.
Connect a dust extraction device
Whenever there are facilities for fitting a dust of fume
extraction system, make sure it is connected and used.
Use recommended accessories
The use of any other accessory or attachment other than
recommended in the instructions or catalogue may pre-
sent a risk of personal injury. Use extension cables suita-
ble for the power input of the grinder (minimum cable
size 1.5mm2). When using a cable reel unwind it fully.
ASSEMBLING THE ACCESSORIES
Ensure the grinder is unplugged from mains.
TO MOUNT THE GUARD
- Remove the flange nut (anticlockwise) and pull the
flange from the spindle (5). Unscrew the 4 screws/
washers (3 and 4) and remove the guard mounting
washer (2).
- Put the guard (1) on the machine raised edge up and
secure with the guard mounting washer and
screws/washers. Tighten the screws firmly.
- Put the flange and flange nut back on the spindle.
Overheating
- The ventilation slots are blocked with dirt. Clean
with dry cloth.
- The machine does not start when switched on.
Check the mains lead and the fuse/plug. Take to your
Ferm Dealer for repair
- The motor is defective . Take to your Ferm Dealer
MAINTAIN TOOLS WITH CARE
Keep the tool clean for better and safer performance.
Store the discs properly in accordance with the maker’s
instructions.
Follow instructions for changing accessories. Inspect
tool and extension cables periodically and if damaged,
have them repaired by a qualified person or authorised
service body. Keep handles free from oil or grease. Keep
the ventilation slots clean to prevent motor overheating.
Check for damaged parts.
Do not use a tool with damaged parts, before further use
a damaged tool must be carefully checked by a qualified
person to determine that it will operate properly. Check
for alignment of moving parts, binding or breakage of
parts, mounting and other conditions that may affect its
operation. A damaged part or guard should be properly
repaired by an authorised service centre, unless indica-
ted otherwise in the instruction manual. Have defective
switches replaced by an authorised service centre. Do
not use a tool if the switch does not turn on and off.
Have your tool repaired by an expert
This appliance is manufactured in accordance with rele-
vant safety standards. Only experts must carry out repai-
ring of electrical appliances, otherwise considerable dan-
ger for the user may result.
Storing tools
When not in use tools should be stored in the dry, out of
reach of children.
ELECTRICAL INFORMATION
This product is complete with a pre-wired mains plug, it
is double insulated in accordance with EN 50144 – no
earth wire is required
If the plug needs replacing follow these instructions.
Wire correctly
The wires in the mains lead are coloured in the following
way:
Blue -Neutral
Brown -Live
Yellow/green -Earth
Securing the wires
Secure wires carefully and firmly to the correct termi-
nals. Secure the mains cable in the plug cord grip firmly
Fit a 5-amp fuse. If a 13amp (BS1363) plug is used a (BS
1362) ASTA approved 5-amp fuse must be fitted.
Recycle/Dispose of old plug and cable
Prevent inadvertent connection to socket and risk of
electric shock.If in doubt always consult a Qualified Elec-
trician
ENVIRONMENT
Recycle the packaging according to the identification
marks on it.
At the end of the product or its accessories life please
recycle where facilities exist - phone the Helpline for
current advice on recycling.
Helpline
For any questions relating to operational or safety
matters contact:
Ferm Customer Helpline on: 0115 966 1199
Monday-Friday 8am – 6pm
Saturday 9am – 1 pm
GUARANTEE
The guarantee conditions can be found on the separately
enclosed guarantee card.
We declare under our sole responsibility that this
product is in conformity with the following
standards or standardized documents
EN-50144-1, prEN50144-2-3,
EN-55014-1, EN-55014-2,
EN61000-3-2, EN61000-3-3,
in accordance with the regulations:
98/37/EEC
73/23/EEC
89/336/EEC
from 01-12-2001
GENEMUIDEN NL
W. Kamphof
Quality department
CE
ı
DECLARATION OF CONFORMITY
(
UK
)
Blue
(Neutral)
Green & Yellow
(Earth)
Brown
(Live)
Fuse
(5 Amp)
Ferm 5
TO MOUNT A GRINDING DISC
- Check the disc is the correct type and does not touch
the edge of the guard.
- Remove the flange nut (12) from the spindle.
- Check the flange (5) is the right way up (flats on
spindle engage with lugs on flange)
- Put a grinding disc (7) on the flange
- Screw the flange nut onto the spindle.
- Press the spindle lock button and turn the spindle (9)
until the lock engages.
- Keeping the spindle lock button pressed, securely
tighten the flange nut with spanner (11) provided.
- Release the spindle lock button and check the spindle
in unlocked by rotating the disc.
MOUNTING THE SIDE HANDLE
- Screw the side handle (3) clockwise into the thre-
aded hole either on the left or right side of the
machine. Check that it is firmly attached and cannot
loosen unexpectedly.
USING THE ANGLE GRINDER
BEFORE OPERATING
- Check the voltage on the angle grinder corresponds
with your power supply voltage and that the plug and
lead are in good condition.
- Check maximum speed marked on the grinding disc
is the same or less than the maximum speed of the
machine. The machine’s speed must not be greater
than the speed marked on the disc.
- You have the correct type of disc for the machine and
that it is mounted correctly. Do not use parts other
than supplied with the machine to make the disc fit
properly
- Ensure the threaded part of the spindle is covered by
the flange nut (12) and cannot touch the grinding sur-
face.
- Inspect the grinding disc for any damage – do not use
cracked, ripped or otherwise damaged discs.
- Set the guard, rotate the guard to the best position to
catch sparks and debris from the disc.
- Run idle for 30 seconds - if there is any abnormal vib-
ration or other fault – switch off, inspect and rectify
before continuing.
OPERATION
- Check the switch is in OFF position
- Plug into a suitable mains supply and switch on.
- To switch ON - slide the switch forwards to the "I"
position.
- To switch OFF press the switch which will jump to
the position "O"
DURING USE
- Do not put the machine down with the motor still
running.
- Keep your finger off the spindle lock button it must
not be pressed while the machine is running
- Do not put the machine down on a dusty surface –
dust will get into the air vents and damage the motor.
- Regularly inspect the disc during use for signs of
damage or wear and replace when required.
- Switch the machine off before removing the plug
from the mains socket.
MAINTENCE, CARE AND
REPAIR
Ensure the grinder is unplugged from the
mains.Switch off and unplug the machine before
carrying out any cleaning or maintenance work.
CLEANING
Do not use flammable liquids to clean the angle grinder
FAULTS
Switch OFF immediately at the mains plug and
remove the plug when:
- The plug or cable is damaged.
- The switch on the machine is defective.
- You smell or see smoke caused by scorched insula-
tion in the machine.
4 Ferm
/
