Astonica 50102626 User manual

Type
User manual

This manual is also suitable for

Read the instructions and precautions before use of this product
Please keep this instruction manual for future reference
®
Model No: 50103528
Superior Leisure 54"
Hexagonal Dining Table
Instruction Manual
For warranty information, please refer to the back page of
this instruction manual.
Due to ongoing product development
the actual product or products may vary from
the illustrations or photos shown within this manual.
NOTE: This product is intended for residential, non-commercial use.
Made in China
©2012 World Factory, Inc.
Distributed by:
World Factory, Inc.
Westlake, TX 76262
111012rev1
For Manuals, Replacement Parts or Customer Service visit:
www.ezreplacement.com
Limited Warranty
World Factory, Inc. Products for Home Use
World Factory, Inc. (Seller) warrants to the original Buyer only, that each Astonica Product will be free
from defects in material and workmanship for a period of one (1) year from date of purchase.
SELLER’S SOLE OBLIGATION AND BUYER’S EXCLUSIVE REMEDY UNDER THIS LIMITED
WARRANTY SHALL BE THE REPAIR OR REPLACEMENT OF PARTS, WITHOUT CHARGE, WHICH
ARE DEFECTIVE IN MATERIAL OR WORKMANSHIP. ANY PARTS AS DETERMINED BY THE SELLER
WHICH HAVE BEEN MISUSED; ABUSED OR DAMAGED EITHER DIRECTLY OR INDIRECTLY FROM
REPAIRS OR ALTERATIONS ATTEMPTED BY UNAUTHORIZED PERSONS; IMPROPER
MAINTENANCE, NEGLECT OR ACCIDENT ARE NOT COVERED BY THIS LIMITED WARRANTY. This
warranty does not apply to damage, heat-induced coloration changes, scratching or alteration due to
normal use or weathering. To make a claim under this Limited Warranty, you must return the complete
product with proof of purchase, transportation prepaid, to any World Factory, Inc. authorized service
center. Call 1-888-422-7800 or visit: ezreplacement.com for the location of the nearest authorized
service center.
Additional Limitations
THIS LIMITED WARRANTY DOES NOT APPLY TO ACCESSORY OR CONSUMABLE ITEMS RELATED
TO THIS PRODUCT. ALL IMPLIED WARRANTIES SHALL BE LIMITED IN DURATION TO ONE (1)
YEAR FROM DATE OF PURCHASE. IN NO EVENT SHALL SELLER BE LIABLE FOR ANY INCIDENTAL
OR CONSEQUENTIAL DAMAGES, INCLUDING BUT NOT LIMITED TO LIABILITY FOR LOSS OF
PROFITS, ARISING FROM THE SALE OR USE OF THIS PRODUCT.
If any provision of this Limited Warranty is for any reason held to be invalid or unenforceable, such
provision shall not affect any other provision herein, this Limited Warranty shall be construed as if
such invalid and/or unenforceable provision had never been contained herein.
This warranty gives you special legal rights, and you may also have other rights which vary from state
to state.
This Warranty contains the entire agreement between Seller and Buyer and supersedes any and all
prior agreements, arrangements, or understandings between the parties relating to product warranty.
1
A
A
A
C
C
PARTS & HARDWARE LIST
PART # DESCRIPTION QUANTITY
A Table Top 1
B Table Legs 6
C Upper Leg Connector Bracket 1
D Lower Leg Connector Bracket 1
E Rubber Table Top Bumper 6
F Flat Washer 24
G Hex Bolts M6x25 12
H Bolt Cap 12
I Nut Cap 12
J Nut 12
K Wrench 1
Carefully remove the contents from the package. If any parts are missing do not
attempt to use the product until they have been obtained and correctly installed.
Parts Detail
NOTE: This product is intended for residential, non-commercial use.
B
B
B
B
D
D
E
E
F
F
F
G
G
H
H
I
I
J
J
K
K
K
ASSEMBLY INSTRUCTIONS
CAUTION: Do not over tighten fasteners.
Figure 1
Figure 2
Figure 3
2
1. (FIGURE 1) Insert the rubber table top
bumpers (E) into the holes located on the
top of the table legs (B).
2. (FIGURE 2) Place the table top (A) upside down
on a flat non-scratch surface. Insert table
legs (B) into leg fittings of the table top (A).
3. (FIGURE 3) Place upper leg connector
bracket (C) between table legs (B) and secure
with hex bolts (G), flat washers (F) and nuts (J)
using hex wrench (K). Do not tighten fully.
4. Place lower leg connector bracket (D) between
table legs (B) and secure with hex bolts (G),
flat washers (F) and nuts (J) using hex
wrench (K). Do not tighten fully.
5. Turn table right side up and tighten nuts (J)
with wrench (K) in a cross corner “X” fashion.
6. Place nut caps (I) and bolt caps (H) on all nuts
and bolts.
  • Page 1 1
  • Page 2 2

Astonica 50102626 User manual

Type
User manual
This manual is also suitable for

Ask a question and I''ll find the answer in the document

Finding information in a document is now easier with AI