WEIHONG NK300CX Quick start guide

Type
Quick start guide

This manual is also suitable for

上海维宏电子科技股份有限公司
SHANGHAI WEIHONG ELECTRONIC TECHNOLOGY CO., LTD.
Quick Start Guide for the Integrated CNC System of Shoe
Molding Machines
Version: 2020.1 1st Version
Author: Product Supporting Department
Weihong Corporation, All Rights Reserved
1 System Overview ............................................................................................................................ 1
1.1 NK300CX Host ..................................................................................................................... 1
1.1.1 Layout ........................................................................................................................ 1
1.1.2 Mounting Dimension (Unit: mm) .................................................................... 4
1.2 WH108C Operation Panel ............................................................................................... 5
1.2.1 Layout ........................................................................................................................ 5
1.2.2 Mounting Dimension (Unit: mm) .................................................................... 8
1.3 Main Software Interface .................................................................................................. 9
2 Basic Commissioning ................................................................................................................. 10
2.1 Set Commissioning Parameters ................................................................................. 10
2.1.1 Set Bus Control System .................................................................................... 10
2.1.2 Set Non-bus Control System ........................................................................... 11
2.2 Adjust the Axis Direction ............................................................................................. 11
2.3 Return to the Machine Origin ..................................................................................... 12
2.3.1 Return to the Machine Origin with an Incremental Encoder ............ 12
2.3.2 Set the Datum with an Absolute Encoder ................................................. 14
2.4 Define the Workpiece Origin ...................................................................................... 15
3 Quick Start ...................................................................................................................................... 16
3.1 Load a Program File ....................................................................................................... 16
3.1.1 Load a Program File from the Internet ...................................................... 17
上海维宏电子科技股份有限公司
SHANGHAI WEIHONG ELECTRONIC TECHNOLOGY CO., LTD.
3.1.2 Set a Machining Task ......................................................................................... 21
3.2 Adjust the WCS ................................................................................................................. 23
3.2.1 Select a WCS .......................................................................................................... 23
3.2.2 Set the Offsets ...................................................................................................... 24
3.3 Execute Tool Calibration .............................................................................................. 25
4 FAQs .................................................................................................................................................. 26
4.1 Axis Servo Alarm ............................................................................................................. 26
4.2 Failed to Register the System ..................................................................................... 27
4.3 Drive 400 Alarm .............................................................................................................. 27
5 Parameter List .............................................................................................................................. 28
5.1 Technic Parameters ....................................................................................................... 28
5.2 Parameters for Approaching the Workpiece Surface ....................................... 30
5.3 Parameters for Selecting Tools .................................................................................. 30
5.4 Parameters for Selecting a Coordinate System ................................................... 30
5.5 Spindle Parameters ........................................................................................................ 30
5.6 Parameters for Z-axis Motion at Pause ................................................................... 31
5.7 REF Parameters ............................................................................................................... 31
5.8 Calibration Parameters ................................................................................................. 31
5.9 Parameters for Action after Cycle ............................................................................. 32
5.10 Feed axis Parameters .................................................................................................... 32
5.11 Other Parameters ............................................................................................................ 33
上海维宏电子科技股份有限公司
SHANGHAI WEIHONG ELECTRONIC TECHNOLOGY CO., LTD.
1 /33
1 System Overview
Integrated CNC System for Shoe Molding Machines consists of hardware and
software:
Hardware
NK300CX host
WH108C Operation panel
Lambda terminal board
Lambda 5S for non-bus control system
Lambda 5M RJ45 for bus control system
Extended terminal board: PCBA EX31A
DB9M/F cables
Servo connecting wires
Software
NcStudio JS software for shoe molding machines
See Main Software Interface for details.
1.1 NK300CX Host
This part introduces the layout and mounting dimension of NK300CX host.
1.1.1 Layout
It introduces the layout of both front view and rear view.
上海维宏电子科技股份有限公司
SHANGHAI WEIHONG ELECTRONIC TECHNOLOGY CO., LTD.
2 /33
1.1.1.1 Front View
The front view of NK300CX host is as follows:
1. USB interface
Used to connect with USB flash disks. And it is protected by a cover.
2. Display area
Human-machine interface, or user’s interface. It is user-friendly and easy to use.
3. Functional keys
There are altogether 6 functional keys, including Gen. (machining), Adv.
(advanced), Prog. (program), Sys (system), Para. (parameter) and Diag.
(diagnosis) keys.
You can access the functional area by directly pressing corresponding
functional key.
4. Operation keys
Including keys from F1 to F8, and page turning keys.
Used to activate the functions indicated by the operation keys, and turn to
previous page or next page.
上海维宏电子科技股份有限公司
SHANGHAI WEIHONG ELECTRONIC TECHNOLOGY CO., LTD.
3 /33
1.1.1.2 Rear View
The rear view of NK300CX host is as follows:
1. DB9M/F cable interface
For NK300CX-H, it is used to connect with the keypad panel.
For NK300CX-V, it is used to connect with the operation panel.
2. Terminal board interface
Used to connect with Lambda terminal board.
3. VGA interface
Used to connect with VGA devices, which are not needed under general
situation.
4. LAN interface
Used to connect with network, with 100Mbps transmission rate.
5. USB interface
Two USB interfaces
Used to connect with USB flash disks.
上海维宏电子科技股份有限公司
SHANGHAI WEIHONG ELECTRONIC TECHNOLOGY CO., LTD.
4 /33
6. Power interface
Used to connect with 220V power supply.
1.1.2 Mounting Dimension (Unit: mm)
NK300CX Dimension
NK300CX Cut-out
上海维宏电子科技股份有限公司
SHANGHAI WEIHONG ELECTRONIC TECHNOLOGY CO., LTD.
5 /33
1.2 WH108C Operation Panel
This part introduces the layout and mounting dimension of WH108C operation
panel used by NK300CX-V.
1.2.1 Layout
The front view of the operation panel is as follows:
1. Alpha-numeric keys
Used to input characters and numbers. Its use is generally the same with that of
the computer keyboard:
Press an alphabet key to enter the alphabet on the right-lower part.
Press Shift key and an alphabet key to enter the alphabet on the left-
upper right.
2. Keys for common operations
Used to enable frequently used operations, including ATC CW, ATC CCW, ATC
OUT, Unclamp, Reset, Simulate, Single Block and HW Guide keys.
上海维宏电子科技股份有限公司
SHANGHAI WEIHONG ELECTRONIC TECHNOLOGY CO., LTD.
6 /33
3. Keys for common ports
Used to turn on / off frequently used ports, including Air, Light, Coolant, Oil
keys, and control rapid movement, including Rapid key.
4. Keys for mode selection
Used to select a machining mode among REF.Point, JOG, Auto, Handle and
Step.
JOG, Handle, Step are referred as Manual mode.
5. Extension keys
Used to customize extension functions, including K1, K2, K3 and K4 keys.
In Shoe Machine Control System, K1 key is used as an air brake key for frock
clamp. Before each machining, the system will judge whether the fixture is
clamped. Only when it is clamped, the system will start machining. Otherwise, a
yellow alarm occurs.
6. Keys for spindle control
Used to control the spindle movement, including CW, Stop and CCW keys.
7. E-stop switch
Used to stop the movement of the machine tool when the machine tool is in
danger, so as to protect the operator and machine tool.
After danger is cleared, you can rotate the switch clockwise to remove the E-
stop alarm.
8. Keys for axis direction
Used to manually move each axis.
In Manual mode:
Press an axis direction key and Rapid key at the same time. The axis
moves at rapid jog speed.
Press an axis direction key. The axis moves at jog speed.
9. Power Switch
Used to control power on or off.
10. Keys for movement control
Used to control the movement of the machine tool
Including START, STOP, Pause, and Resume keys.
上海维宏电子科技股份有限公司
SHANGHAI WEIHONG ELECTRONIC TECHNOLOGY CO., LTD.
7 /33
11. Spindle override knob
Used to adjust spindle override from 50% to 150%.
When parameter N72003 G00 F Fixed is set to No, the knob is used as G00
override knob and used to adjust G00 override from 0 to 100%.
12. Feed override knob
Used to adjust feed override from 0 to 120%.
上海维宏电子科技股份有限公司
SHANGHAI WEIHONG ELECTRONIC TECHNOLOGY CO., LTD.
8 /33
1.2.2 Mounting Dimension (Unit: mm)
WH108C Dimension
WH108C Cut-out
上海维宏电子科技股份有限公司
SHANGHAI WEIHONG ELECTRONIC TECHNOLOGY CO., LTD.
9 /33
1.3 Main Software Interface
The interactive user interface for NcStudio Software for Shoe Molding Machines
in Auto mode is as follows:
1. Status bar
It shows the following information:
Current mode, such as Auto, JOG, etc.
Current status of the machine tool, such as RUN, IDLE, etc.
Name of the loaded program file.
Machining time.
2. Information bar
It shows information, such as machining process, alarms, etc.
3. Functional area
It shows child interfaces corresponding to each main functional keys.
4. Functional keys
It show commands corresponding to F1 ~ F8 operation keys.
It differs with the child interfaces.
上海维宏电子科技股份有限公司
SHANGHAI WEIHONG ELECTRONIC TECHNOLOGY CO., LTD.
10 /33
2 Basic Commissioning
Through this section, you can quickly know the following basic commissioning
processes for Integrated CNC System for Shoe Molding Machines:
1. Set commissioning parameters.
2. Adjust the axis direction.
3. Return to the machine origin.
4. Define the workpiece origin.
2.1 Set Commissioning Parameters
The integrated CNC system supports both the bus control system and the non-bus
control system.
To set the type of control system, press 1 F4, modify the value of
parameter N50000 Control System Type.
2.1.1 Set the Bus Control System
This operation is used to set commissioning parameters for bus control system.
Before setting commissioning parameters for the bus control system, ensure the
following:
Parameter N50000 Control System Type is set to 1.
The used terminal board is Lambda 5M RJ45.
To set commissioning parameters for the bus control system, do the following:
1. To enter Param functional area, press .
2. To enter Axis Interface, press 2.
3. Find and set the following axis parameters:
N11000 Encoder Feedback
N11020 Axis Encoder Type
N16000 Drive Station Address
N16020 Encoder Digit
N74100 Lead Screw Pitch
N10010 Pulse Equivalent
N16030/N16040 Electronic Gear Ratio
See Parameter List for details.
上海维宏电子科技股份有限公司
SHANGHAI WEIHONG ELECTRONIC TECHNOLOGY CO., LTD.
11 /33
2.1.2 Set the Non-bus Control System
This operation is used to set commissioning parameters for the non-bus control
system.
Before setting commissioning parameters for the non-bus control system, ensure
the following:
Parameter N50000 Control System Type is set to 0.
The used terminal board is Lambda 5S.
To set commissioning parameters for the non-bus control system, do the following:
1. To enter Param functional area, press .
2. To enter Axis Interface, press 2.
3. Find and set the following operation parameters:
N11000 Encoder Feedback
N11020 AXis Encoder Type
N74020 Coarse Positioning Dir.
N74030 F in Coarse Positioning
N74050 Fine Positioning Dir.
N74060 F in Fine Positioning
N74100 Lead Screw Pitch
N74130/N74140 Mechanical Reducer Ratio
See Parameter List for details.
2.2 Adjust the Axis Direction
This operation is used to check if the positive direction of each axis is the same with
the direction specified by Right Hand Rule, and adjust it if not, so as to avoid
damage to the machine tool due to incorrect direction.
Taking X-axis as an example, to check the axis direction, do the following:
1. Press 2 F8 and check the value of parameter N10000 Axis
Direction(X):
1: positive
-1: negative
2. Judge the positive direction of X-axis according to Right Hand Rule.
上海维宏电子科技股份有限公司
SHANGHAI WEIHONG ELECTRONIC TECHNOLOGY CO., LTD.
12 /33
3. In JOG / Handle / Step mode, press X+ to move X-axis, and observe its moving
direction.
4. Optional: If the actual moving direction is opposite to the judged direction,
modify the value of parameter Axis Direction(X) to the opposite value.
Example
The current value of parameter Axis Direction(X) is 1. And you find X-axis moves
towards the negative direction after pressing X+.
Then, you need to change the value of the parameter to -1.
2.3 Return to the Machine Origin
This operation is used to adjust the coordinate position before machining.
According to the encoder type, it can be divided into the following:
Return to the machine origin with an incremental encoder.
Set the datum with an absolute encoder.
To set the encoder type, press 2 F8, input the manufacturer password,
and modify the value of parameter N11020 Axis Encoder Type.
2.3.1 Return to the Machine Origin with an Incremental Encoder
This operation is used to return to a fixed point, i.e. machine origin, assigned by
design, manufacturing and debugging before the machine tool leaves factory.
Before returning to the machine origin with an incremental encoder, check the
motor nameplate and ensure the value of parameter N11020 Axis Encoder Type is
set to 0.
上海维宏电子科技股份有限公司
SHANGHAI WEIHONG ELECTRONIC TECHNOLOGY CO., LTD.
13 /33
To return to the machine origin with an incremental encoder, do the following:
1. In REF mode, to enter Coor interface, press 1:
2. Press one of the following:
F1: return X-axis to the machine origin.
F2: return Y-axis to the machine origin.
F3: return Z-axis to the machine origin.
F5: return X-axis and Y-axis to the machine origin at the same time.
F8: return all axes to the machine origin in order of Z-axis, X-axis and Y-
axis.
Note: The system entitles Z-axis the highest priority in returning to the machine origin by default.
For safety, it is suggested to firstly return Z-axis and then return X-axis and Y-axis at the same time.
After returning, the sign appears in front of related axes in the coordinate
display area.
上海维宏电子科技股份有限公司
SHANGHAI WEIHONG ELECTRONIC TECHNOLOGY CO., LTD.
14 /33
2.3.2 Set the Datum with an Absolute Encoder
This operation is used to return to the machine origin with an absolute encoder by
directly setting the datum at the first time to use the system.
Compared to returning to the machine origin with an incremental encoder, it owns
the following advantages:
No need to set returning orders for all axes in datum setting process.
No need to return to the machine origin again after restarting the system, and
recovering from power interruption and E-stop because the system will
automatically read the datum information.
Note: You need to set the datum again after replacing battery of the absolute encoder.
Before setting the datum with an absolute encoder, do the following:
Check the motor nameplate and ensure the value of parameter N11020
Encoder Type is set to 1.
Set the values of WISE drive parameter Pr015 Absolute Encoder Setting to 0,
and software parameter N11000 Encoder Feedback to Yes.
To set the datum with an absolute encoder, do the following:
1. Taking Z-axis as an example, to set the datum with an absolute encoder for Z-
axis, do the following:
1. Manually move Z-axis to the fixed position of the machine tool.
2. In REF mode, press 1 F7.
3. Press F3.
The system automatically reads and records Z-axis machine coordinates.
And the sign appears in front of Z-axis in the coordinate display area
after successfully setting datum.
2. To set the datum with an absolute encoder for the other axes, repeat step 1:
F1: return X-axis to the machine origin.
F2: return Y-axis to the machine origin.
F5: return X-axis and Y-axis to the machine origin at the same time.
Note: F8 means returning all axes to the machine origin in order of Z-axis, X-axis and Y-axis.
3. Restart the software to validate the setting.
Note: Because of time sequence, it takes time for the software to read absolute data, possible resulting in
interface choking in datum setting.
上海维宏电子科技股份有限公司
SHANGHAI WEIHONG ELECTRONIC TECHNOLOGY CO., LTD.
15 /33
After setting the datum with an absolute encoder, you can export the set datum by
pressing F1 in the next page to save it to the root directory of a USB flash disk. When
a new software is installed, you can import the previously saved datum by pressing
F2 in the next page, so as to save the trouble of repeated setting.
2.4 Define the Workpiece Origin
Based on a certain point on the workpiece, this operation is used to define the origin
of workpiece coordinate system (Hereinafter referred as to WCS ). Namely, it is fixed
relative to the certain point and mobile relative to the machine origin.
The selection of workpiece origin should meet the conditions of simple
programming, simple dimensional conversion, and small machining error, etc.’
If Machining Setting is set as double-axis mode, you need to separately do
centering for X1-axis and X2-axis. At this time, the other axes should be still.
To define the workpiece origin, do the following:
1. In Handle mode, to open Line Centering dialog box, press 1
F2:
2. To select the target workpiece coordinate system, press .
3. Optional: Set the spindle speed during centering in S in Centering input box.
A large value is not suggested. And it is set to 500 RPM by default.
4. Optional: To enable edge finder for accurate centering, press F6:
5. Move X1-axis to one side of the workpiece and X2-axis to the other side, and
press F1.
The system automatically records the coordinates of X1-axis and X2-axis.
上海维宏电子科技股份有限公司
SHANGHAI WEIHONG ELECTRONIC TECHNOLOGY CO., LTD.
16 /33
6. Exchange positions of X1-axis and X2-axis and press F2.
The system automatically calculates the midpoint coordinate of X1-axis and X2-
axis separately based on the coordinates of X1-axis and X2-axis recorded in
step 5 and step 6, and separately sets the midpoints of X1-axis and X2-axis as
their workpiece origins.
Note: In single-axis mode, if you press F1 or F2, operations are only effective to X1-axis or X2-axis.
7. According to step 5 and step 6, set the the workpiece origin of Y-axis and press
F7 in Coor interface.
X-axis and Y-axis move to the workpiece origin specified by centering and Z-
axis is on the upper limit of workbench travel.
3 Quick Start
Through this section, you can quickly know the following machining processes for
Integrated CNC System for Shoe Molding Machines:
1. Load a program file.
2. Adjust the WCS.
3. Calibrate after tool changed.
3.1 Load a Program File
A shoe mold has multiple faces, and each face corresponds to a program file.
To load program files, do one of the following:
To machine one face of a shoe mold, load a program file from the following path:
The host: Program files saved in the root directory of the host
D:\\NcFiles.
A USB flash disk: Program files saved in the root directory and
subdirectory of the USB flash disk.
The internet: Program files saved in the host or the network.
It is similar to load a program file from these three paths. This section takes
Load a Program File from the Internet as an example.
To machine the whole shoe mold at a time, set a machining task and load all
program files.
上海维宏电子科技股份有限公司
SHANGHAI WEIHONG ELECTRONIC TECHNOLOGY CO., LTD.
17 /33
3.1.1 Load a Program File from the Internet
This operation is used to establish network connection between the integrated CNC
system for shoe molding machine and PC, to realize two-way transmission between
them.
To load a program file from the internet, do the following:
1. Set the IP address.
2. Verify the connection.
3. Access a shared program file.
3.1.1.1 Set the IP Address
This operation is used to establish the network connection channel between the
integrated CNC system and the PC by automatically obtaining or manually setting
the IP address.
It is default to automatically obtain the IP address. And this operation takes
manually setting the IP address as an example.
Before setting the IP address, ensure that the integrated CNC system and PC are in
the same subnet.
To manually set the IP address, do the following:
1. Press 2 F1. Network Setting dialog box pops up:
2. To not automatically obtain the IP address, press .
上海维宏电子科技股份有限公司
SHANGHAI WEIHONG ELECTRONIC TECHNOLOGY CO., LTD.
18 /33
3. Press or to select the target input box, and set the following addresses:
IP address
E.g. 192.168.1.188 (the first three digits should be the same with that of
PC, and the last digit should be different from that of PC)
Subnet mask:
It is the same with PC.
Default gateway:
It is the same with PC.
4. To close Network Setting dialog box and save the settings, press F7.
The new networking information shows in Network Connection Status area in
Computer interface.
3.1.1.2 Verify the Connection
This operation is used to verify whether the IP addresses are set successfully by
ping command after the IP addresses of the integrated CNC system and PC are set
well.
To verify the connection, do the following:
1. To open the command window, press Win and R keys on the keyboard of PC,
and input cmd in Run dialog box.
2. Input ping and IP address of the integrated CNC system.
E.g. ping 192.168.0.1
  • Page 1 1
  • Page 2 2
  • Page 3 3
  • Page 4 4
  • Page 5 5
  • Page 6 6
  • Page 7 7
  • Page 8 8
  • Page 9 9
  • Page 10 10
  • Page 11 11
  • Page 12 12
  • Page 13 13
  • Page 14 14
  • Page 15 15
  • Page 16 16
  • Page 17 17
  • Page 18 18
  • Page 19 19
  • Page 20 20
  • Page 21 21
  • Page 22 22
  • Page 23 23
  • Page 24 24
  • Page 25 25
  • Page 26 26
  • Page 27 27
  • Page 28 28
  • Page 29 29
  • Page 30 30
  • Page 31 31
  • Page 32 32
  • Page 33 33
  • Page 34 34
  • Page 35 35
  • Page 36 36

WEIHONG NK300CX Quick start guide

Type
Quick start guide
This manual is also suitable for

Ask a question and I''ll find the answer in the document

Finding information in a document is now easier with AI