Fujitsu WSHG160DJ6/WOHG160LJL Installation guide

INSTALLATION

Air to Water Heat Pump Split single service

For professionals. To be kept by the user for future reference

U0651697_2016_EN_2

10/09/2019

EN

Outdoor unit

WOHG160LJL

Hydraulic unit

WSHG160DJ6

■ Installation and maintenance rules

The appliance must be installed and maintained

by an approved professional in accordance with

current regulations and codes of practice.

• Warning, hydraulic unit should not be installed

in an air current.

■ Handling

The outdoor unit must not be placed in a horizontal

position during transport.

If not kept upright during transport, the appliance

could be damaged through displacement of

the refrigerant and damage to the compressor

suspension.

Any damage caused by transportation in a horizontal

position is not covered by the warranty.

If necessary, the outdoor unit may be tilted only

during manual handling (to go through a door or up

a staircase). This operation must be conducted very

carefully and the appliance must be immediately

restored to the upright position.

■ Containment of refrigeration circuits

All refrigeration circuits are sensitive to contamination

from dust and moisture. If such pollutants penetrate

the refrigeration circuit, they can aect the reliability

of the heat pump.

Make sure that the connections and refrigeration

circuits (hydraulic unit, outdoor unit) are

protected correctly.

In the event of a subsequent failure and following

an inspection, the presence of moisture or

foreign bodies in the compressor oil would

automatically void the warranty.

- Check upon receipt that the ttings and refrigeration

circuit caps mounted on hydraulic unit and outdoor

unit are properly seated and secured (cannot be

loosened with bare hands). If this is not the case,

tighten them using a C spanner.

- Check also that the refrigeration connections are

sealed (plastic caps or tubes crimped at the ends

and brazed). If the caps must be removed during

the installation (tubes to be re-cut for example),

put them back as soon as possible.

■ Hydraulic connections

The connection must comply with industry standard

practice according to current regulations.

Remember: Seal everything when tting in

accordance with industry standard practice for

plumbing work:

- Use suitable seals (bre gasket, O-ring).

- Use Teon or hemp tape.

- Use sealing paste (synthetic depending on the

case).

Use glycol/water mix if the minimum ow

temperature is set below 10°C. If you are using a

glycol/water mix, arrange for an annual check on the

quality of the glycol. Use monopropylene glycol only.

The recommended concentration is 30% minimum.

Never use monoethylene glycol.

• In some installations, the presence of dierent

metals can cause corrosion problems; the

formation of metal particles and sludge can

appear in the hydraulic circuit.

• In this case, it is advisable to use a corrosion

inhibitor in the proportions indicated by the

manufacturer.

• You must also ensure that treated water does

not become corrosive.

■ Electrical connections

• Before any maintenance operation, ensure

that the general power supply is switched o.

• Specications of electricity supply

The electrical installation must be carried out in

accordance with prevailing rules.

Electrical connections will only be made once all

other installation operations (fastening, assembly,

etc.) have been completed.

Warning!

The contract signed with the energy provider must

be sucient not only to cover the heat pump's power

requirements but also the combined sum of all the

appliances likely to be operating at the same time. If

the power is too low, check the power rating stated

in your contract with your energy provider.

Never use a power socket for the power supply.

The heat pump must be supplied directly with power

(without external switch) by special protected leads

from the electric panel via dedicated bipolar circuit

breakers, C curve for the outdoor unit, C curve for

the electrical heating and domestic water backups

(see tables page 35).

The electrical installation must be tted with a 30mA

RCD.

This appliance is designed to operate using a

nominal voltage of 230 V or 400 V, +/- 10%, 50 Hz

(depending on model).

• General remarks on electrical connections

It is essential to maintain neutral-phase polarity

when making electrical connections.

Rigid wires are preferable for xed installations,

particularly in a building.

Tighten the cables using the cable glands to prevent

the feed wires from being accidentally disconnected.

The earth connection and its continuity must be

ensured.

• Cable glands

To ensure the stability of power (Low Voltage) and

sensor (Extra-Low Voltage) cables, it is essential

that the cable glands are tightened according to the

following recommendations:

Size of cable

gland (PE)

(mm)

Diameter of

cable

(mm)

Cable gland

tightening

torque

(check-nut)

(N.m)

Coupling net

tightening

torque

(N.m)

PG7 1 to 5 1.3 1

PG9 1.5 to 6 3.3 2.6

PG16 5 to 12 4.3 2.6

• Connecting to screw terminals

The use of ring, spade or blade terminals or

caps is prohibited.

- Always select wire that complies with current

standards.

- Bare the end of the wire to around 25 mm.

- With round end pliers, form a loop with a diameter

which matches the tightening screws on the

terminal.

- Tighten the terminal screw rmly onto the

loop created. Insucient tightening can cause

overheating, leading to breakdown or even re.

Rigid wires

Loop

25 mm

Lug on

exible wires

prohibited

Screw and special

washer

Terminal

• Connecting to controller boards

- Remove the corresponding connector and make

the connection.

Pre-cabled bundle connector and/or screw connector

• Connecting to spring terminals

- Bare the end of the wire to around 12 mm.

- Push the spring with a screwdriver so that the wire

enters the cage.

- Slide the wire into the opening provided for this

purpose.

- Remove the screwdriver and then check that the

wire stays gripped by the cage by pulling on it.

2

1

3

- 4 -

Contents

Packing .................................6

Unpacking and supplies ....................6

Denitions ...............................6

Optional equipment ........................6

Operating Range ..........................6

General characteristics .....................7

Description .............................12

Operating principle .......................14

 Hydraulic connections 30

Connecting the hydraulic unit to the heating circuit ..30

Filling and bleeding the installation ...........31

Heating circulation pump speed settings .......32

 Electrical connections 34

Cable dimensions and protection rating .......35

Electrical connections on the outdoor unit side ..36

Electrical connections on the hydraulic unit side ..38

Outside sensor ..........................42

Room sensor (optional) ....................42

 Commissioning 44

 Controller Interface 46

User Interface ...........................46

Display Description .......................47

Installer Menu ...........................48

Navigating the Menus .....................48

Modifying Settings ........................49

Temperature control ......................50

 Description of the equipment 6

 Installation 16

Installation of refrigeration connections ........16 Installation of the outdoor unit ...............18

Installation of the hydraulic unit ..............20

 Refrigeration connections 22

Rules and precautions .....................22

Shaping the refrigeration pipes ..............22

Checks and connection ....................25

Filling the installation with gas ...............26

Waterstage / Installation / 2016 - EN

- 5 -

 Controller Menu 52

Basic Hydraulic Layout 70

Electrical Cabling Plans 72

 Fault Diagnosis 76

Faults in the Hydraulic Unit .................76 Faults in the Outdoor Unit ..................77

 Maintenance of the installation 78

Hydraulic checks .........................78

Checking the outdoor unit ..................78

Electrical checks .........................78

 Other maintenance 79

Emptying the hydraulic unit .................79 Distribution valve .........................79

 Quick-start procedure 80

Menu Structure ..........................52

Installed options .........................53

Hydraulic conguration ....................53

Heat Pump Conguration ..................58

System status ...........................60

Auxiliary functions ........................62

Settings ................................64

Easy Start ..............................68

Start-up check-list ........................80 Commissioning technical datasheet ..........82

 Instructions for the end user 83

Waterstage / Installation / 2016 - EN

- 6 -

►

Packing

• 1 package : Outdoor unit.

• 1 package : Hydraulic unit and outside temperature

sensor.

►

Unpacking and supplies

While the courier is still present, carefully check the

general appearance of the appliances and check

that the outdoor unit has not been laid in a horizontal

position.

In the event of a dispute, send any relevant reservations

to the carrier in writing within 48 hours and send a copy

of the letter to Customer Services.

►

Denitions

- Split: The heat pump consists of two elements

(an outdoor unit to be installed outdoors and a hydraulic

unit to be installed inside the dwelling).

- Air/water: The surrounding air is the energy source.

This energy is transmitted to the heating circuit water

by the heat pump.

- Inverter: The fan and compressor speeds are

modulated according to the heating requirements.

This technology enables you to save on energy and

operate on a single-phase power supply, whatever

the heat pump's output, by avoiding pulling signicant

amounts of current at start-up.

- COP (Coecient of Performance): This is the

relationship between the energy transmitted to the

heating circuit and consumed electrical energy.

 Description of the equipment

Waterstage / Installation / 2016 - EN

Packing contents list

Heat Pump Outdoor unit Hydraulic unit

Model Reference Code

Waterstage SHP 16 WOHG160LJL WSHG160DJ6

►

Optional equipment

• Dual circuit kit (code UTW-KZSXJ)

for connecting 2 heating circuits.

• Regulation extension kit (code UTW-KREXD)

to manage a 2nd heating circuit, swimming pool,

telephone modem etc...

• DHW kit (code UTW-KDWXD)

for connecting a mixed DHW tank

(with built-in electrical backups).

• Boiler connection kit (code UTW-KBSXJ)

for connecting a boiler to the heat pump.

• Room thermostat (code UTW-C55XA),

Wireless room thermostat (code UTW-C58XD)

for correcting the ambient temperature.

• Remote control (code UTW-C74TXF or UTW-C74HXF),

Wireless remote control (code UTW-C78XD)

for correcting the ambient temperature and

programming the heat pump.

• Cooling kit (code UTW-KCLXD).

• High ow rate circulation pump kit (code UTW-PHFXG)

for the installation of 1 underoor heating circuit.

►

Operating Range

This heat pump provides:

- Heating in winter,

- The management of electrical backups, for extra

heating on the coldest days,

or

- Installation with boiler connection* for extra heating on

the coldest days,

- Management of two heating circuits*,

- Production of domestic hot water* (provided that it is

combined with a mixed DHW tank),

- Cooling in summer* (for underoor heating-cooling

system or fan-convectors).

*: These options require the use of additional kits

(see chapter "Required accessory" or "Optional equipment").

- 7 -

Model name Waterstage SHP 16 TRI 15 TRI 17

Rated heating performances (outdoor temp. / ow temp.)

Heat output

+7°C/+35°C - Underoor heating system kW 16.00 15.00 17.00

-7°C/+35°C - Underoor heating system kW 14.50 13.20 15.00

+7°C/+55°C - Radiator kW 14.50 13.20 15.00

-7°C/+55°C - Radiator kW 10.90 13.20 14.20

Power consumption

+7°C/+35°C - Underoor heating system kW 3.86 3.46 4.10

-7°C/+35°C - Underoor heating system kW 5.27 4.55 5.32

+7°C/+55°C - Radiator kW 5.58 4.77 5.49

-7°C/+55°C - Radiator kW 5.89 6.77 7.40

Coecient of performance (COP) (+7°C/+35°C) 4.15 4.33 4.15

Electrical specications

Electrical voltage (50 HZ) V 230 400 400

Maximum current for appliance A 28 14 14

Nominal current A 17.2 6.43 7.4

Maximum current of the Heating system electrical backup A 26.1 39 39

Power of the Heating system electrical backup kW

6 kW

(single phase)

9 kW

(3-phase)

9 kW

(3-phase)

Circulation pump actual power consumption W 39.5 39.5 39.5

Maximum power consumed by the outdoor unit W 6300 6770 7400

Hydraulic Circuit

Maximum operating pressure MPa (bar) 0.3 (3) 0.3 (3) 0.3 (3)

Available heating pressure at nominal point +7°C / +55°C (Δt8) MPa (bar) 0.05 (0.5) 0.055 (0.55) 0.045 (0.45)

Minimum allowed hydraulic ow rate l/h 600 600 600

Miscellaneous

Weight of outdoor unit Kg 137 138 138

Noise level at 5 m

1

(Outdoor unit) dB (A) 45 45 45

Sound power level in accordance with EN 12102

2

(Outdoor unit) dB (A) 67 67 67

Weight of hydraulic unit (empty / full of water) Kg 53 / 75 53 / 75 53 / 75

Hydraulic unit water capacity l 30 30 30

Noise level at 1 m

1

(Hydraulic unit) dB (A) 37 37 37

Sound power level in accordance with EN 12102

2

(Hydraulic unit) dB (A) 45 45 45

Heating system operating limits

Outdoor temperature min/max °C -25 / +35 -25 / +35 -25 / +35

Max. heating water ow temperature underoor heating °C 45 45 45

Max. heating water ow temperature low temperature radiator °C 60 60 60

Min. ow water temperature °C 8 8 8

Refrigeration circuit

Gas pipe diameters Inches 5/8 5/8 5/8

Liquid Piping Diameters Inches 3/8 3/8 3/8

Factory ll of refrigerant R410A

3

g 3800 3800 3800

Maximum operating pressure MPa (bar) 4.15 (41.5) 4.15 (41.5) 4.15 (41.5)

Minimum / Maximum length of pipes

4 / 6

m 5 / 15 5 / 15 5 / 15

Maximum length of pipes

5

m 30 30 30

Maximum level dierence

(Outdoor unit over hydraulic unit and heating only / Other cases)

m 25 / 15 25 / 15 25 / 15

►

General characteristics

1

Sound pressure level at (x) m from the appliance, 1.5m off the ground, open eld

directionality 2.

2

The sound power level is a laboratory measurement of the emitted sound power. It

does not correspond to a measurement of the perceived sound power.

3

Refrigerant R410A as per NF EN 378.1 standard.

4

Filling with refrigerant R410A is done at the factory.

5

Taking into account a possible additional ll of refrigerant R410A (see "Additional

lling", page 28).

6

The announced thermal and acoustic performances are measured with 7.5m length

refrigerant lines.

Waterstage / Installation / 2016 - EN

- 8 -

Ø22.2

196 196

688

1080

40

39.3

480

12.1

23.6

1428

515.5

37.7

Ø50

Ø34.5

g. 1 - Dimensions of outdoor units (in mm)

Waterstage / Installation / 2016 - EN

■ Waterstage SHP 16

- 9 -

450

9897

471

493

81

847

805

Heating return

ø M 26x34

Heating ow

ø M 26x34

Space requirements of the hydraulic unit, see page 20.

g. 2 - Dimensions of hydraulic unit (in mm)

1*

3**

2*

4

1 Elbow

for condensate evacuation.

2

Plugs (x9)

(depending on

model)

g. 3 - Accessories provided with the outdoor unit

8

5 6

7

5 Bracket for attaching hydraulic unit.

6 Outside sensor to monitor the outdoor temp.

g. 4 - Accessories provided with the hydraulic unit

■ Hydraulic unit

Waterstage / Installation / 2016 - EN

- 10 -

-50

1000

10000

43907

2490

338

-25025 50 75

°C

0

2500

5000

7500

10000

12500

15000

17500

20000

22500

25000

27500

30000

32500

0102030405060708090 100

B3977

Outside sensor QAC34

HP return sensor

HP ow sensor

g. 5 - Available hydraulic pressures and ow rates

0

1

2

3

4

5

6

7

8

mCE

1 mbar=10 mmCE=100 Pa

m/h

3

1

1,5 20,50

0 0,5 1 1,5 2

m

3

/h

1

3

55

77

88

0

1

2

3

4

5

6

7

8

mCE

1 mbar=10 mmCE=100 Pa

m/h

3

1

1,5 20,50

0 0,5 1 1,5 2

m

3

/h

1

3

55

77

88

Variable pressure Constant pressure

g. 6 - Ohmic sensor values (Hydraulic unit)

Waterstage / Installation / 2016 - EN

- 11 -

g. 7 - Ohmic sensor values (Outdoor unit)

-20 -10 0 10 20 30 40 50 60 70 80 90 100 110 120 130

10000

1000

100

10

1

- Compressor

- Discharge

- Condensation

- Expansion valve

- Evaporator inlet

- Outdoor unit

Temperature °C

Ohmic value (kΩ)

Waterstage / Installation / 2016 - EN

- 12 -

►

Description

g. 8 - Outdoor unit components

Key:

1. High performance and low noise impeller.

2. Electrical motor with variable "Inverter" operation.

3. "Inverter" control unit.

4. Check lights and buttons.

5. Connection terminal blocks

(power supply and interconnection).

6. Refrigerant storage bottle.

7. 4-way valve.

8. Anti-corrosion treated bodywork.

9. Main circuit electronic expansion valve.

10. Noise and thermally insulated "Inverter" compressor with liquid injection port.

11. Refrigeration connection valves (ared connectors) with protective caps.

12. Holding tank with condensate drain hole.

13. High-performance exchange surface evaporator; anti-corrosion treated hydrophilic aluminium ns and

grooved copper tubes.

14. Solenoid valve for liquid injection.

1

8

2

1

2

12

13

3

4

14

6

7

5

11

9

10

Waterstage / Installation / 2016 - EN

■ Waterstage SHP 16

- 13 -

g. 9 - Hydraulic unit components

Key:

1 - Electric box.

2 - User interface.

3 - Start/stop switch.

4 - Pressure gauge.

5 - Heating circulation pump.

6 - Heating ow.

7 - Heating return.

8 - "Gas" refrigeration connection.

9 - "Liquid" refrigeration connection.

10 - Drain valve.

11 - Safety valve.

12 - Flowmeter

13 - Automatic bleeder valve.

14 - Expansion vessel.

15 - HP electrical backup.

16 - Condenser.

2

1

14

5

3 4

9

8

67

10

11

12

8

5

15

16

13

■ Hydraulic unit

Waterstage / Installation / 2016 - EN

- 14 -

►

Operating principle

The heat pump transmits the energy contained in the

surrounding air into the dwelling to be heated.

The heat pump consists of four main elements, in which

a refrigerant (R410A) circulates.

- In the evaporator (ref. 13, g. 8, page 12):

The calories are taken from the outside air and

transmitted to the refrigerant. Because it has a low

boiling point, it changes from a liquid to a vapour, even

in cold weather (down to -25°C outside temperature).

- In the compressor (ref. 10, g. 8, page 12):

The vaporised refrigerant is pressurised and takes on

even more calories.

- In the condenser (ref. 14, g. 9, page 13):

The energy of the refrigerant is transmitted to the

heating circuit. The refrigerant returns to its liquid state.

- In the expansion valve (ref. 9, g. 8, page 12):

The liqueed refrigerant is returned to a low pressure

and regains its initial temperature and pressure.

The heat pump is equipped with a controller which

controls the room temperature based on the outdoor

temperature measurement. The room thermostat

(option) provides a corrective action for the temperature

control.

The hydraulic unit is tted with an electrical backup or

boiler connection which intervenes to provide additional

heat during the coldest periods.

• Control functions

- The heating circuit's ow temperature is controlled by

the temperature control.

- Depending on the heating ow temperature,

the outdoor unit's power is modulated by the "Inverter"

compressor.

- Control of the backup electrical heating.

- The daily timer program is used to set the periods

where the ambient temperature is comfortable or

reduced.

- Summer/winter time mode switchover is automatic.

- Management of the boiler backup*.

- Room sensor*: The room sensor provides a corrective

action for the temperature control.

- Control of a second heating circuit*.

- Domestic hot water*: Heating timer program.

- Managing cooling*.

* Where the heat pump is tted with options and associated kits.

• Protective functions

- Anti-legionella cycle for domestic hot water.

- Frost protection: Frost protection cuts in if the heating

circuit's ow temperature falls below 5°C (provided

that the heat pump's electrical power supply is not

interrupted).

8

7

6

5

4

3

2

1

0

-20 -15 -10 -5 0 510152025

46

Dwelling heat loss (kW)

Outdoor temperature (°C)

HP power

g. 10 - Examples and operating limits

Max

authorised HP

start-up temp.

Water return temperature (°C)

HP only

Heat Pump

HP +

electrical

backup

Backup

Waterstage / Installation / 2016 - EN

- 15 -

• Domestic hot water (DHW) operating principle

Two domestic hot water (DHW) temperatures can be

set: comfort and reduced.

The default DHW program is set to the comfort

temperature between 00:00 and 05:00 and between

14:30 and 17:00 and to the reduced temperature for the

rest of the day. This optimises electrical consumption

while ensuring comfortable heating and water

temperatures.

The reduced temperature setpoint may be useful to

avoid restarting the DHW too often and for too long

during the day.

The production of domestic hot water (DHW) is started

when the temperature in the tank drops to 7°C below

the temperature setpoint.

The heat pump produces the domestic hot water, which

is then additionally heated, if required, by the tank's

electrical backup or by the boiler. To ensure a DHW

setpoint over 55°C, the electrical backup heating must

be left on.

Depending on the setting, the comfort temperature can

be reached 24h/day or only at night or following the

DHW program.

If the contract signed with the energy provider includes

a day/night tari, the electrical backup is subject to the

supplier’s power tari and the comfort temperature may

only be reached at night.

If no particular contract has been signed, the comfort

temperature can be reached at any time, including

during the day.

The production of DHW takes priority over heating;

nevertheless the production of DHW is managed

by cycles that regulate the amount of time assigned

to heating and production of DHW in the event of

simultaneous demand.

Anti-legionella cycles can be programmed.

• Fan convectors with integrated control system

Do not use a room sensor in the area in question.

g. 11 - Heat pump operating principle

Ev

Dt

Cn

Cp

1kW

COP 4

4kW

20 °C

PAC

PAC - Heating Pump

Ev - Evaporator

Cp - Compressor

Cn - Condenser

Dt - Expansion Valve

Air energy

Heat produced

Electrical

energy

consumed

Waterstage / Installation / 2016 - EN

- 16 -

 Installation

g. 12 - Example of recommendation for layout of

refrigeration connections

►

Installation of refrigeration

connections

Bend the pipes into position and make holes

for them through the oor or walls either with

their protective caps in place or after brazing.

Keep the protective caps in place or ends

brazed until the appliance is commissioned.

The outdoor unit must be connected to the hydraulic unit

only with brand new separately insulated copper

connections (refrigerant quality).

Maintain the same pipe diameters (g. 19).

Observe the maximum and minimum distances

between the hydraulic unit and the outdoor unit

(g. 19, page 24); the guarantee of performance and

the service lifespan of the system depend on this.

The minimum length of the refrigeration

connections for correct operation is 5 m.

The appliance's warranty will be void if it is operated

with refrigeration connections less than 5 m long

(tolerance +/- 10%).

If the refrigeration connections are exposed to

weathering or UV radiation and the insulation is not

resistant, protection must be provided.

Waterstage / Installation / 2016 - EN



- 18 -

• Water may ow out of the outdoor unit when it is

operating. Do not install the unit on a paved terrace;

choose a well-drained location (e.g. gravel or sand).

If installation is carried out in an area where the

temperature stays below 0°C for long periods, check

that the presence of ice does not present any danger.

A drainage pipe can also be connected to the outdoor

unit (see g. 14).

• Nothing should obstruct the air circulation through the

evaporator and out from the fan (g. 13).

• Keep the outdoor unit away from heat sources and

ammable products.

• Make sure that the unit does not disturb the

surrounding area or inhabitants (noise level, draught,

low temperature of the ejected air freezing the plants

in its path).

g. 13 - Minimum installation clearances around the outdoor unit (all models)

B

E

G

D

BB

A

G

B

H

A

B

D

E

G

B

F

J

B

K

E

F

H

B

H

E

D

H

B

H

B

D

B

H

E

A ≥ 80 mm

B ≥ 100 mm

C ≥ 200 mm

D ≥ 300 mm

E ≥ 500 mm

F ≥ 600 mm

G ≥ 1000 mm

H ≥ 1500 mm

J ≥ 2000 mm

K ≥ 3000 mm

►

Installation of the outdoor unit

▼

Installation precautions

The outdoor unit must only be installed

outside. If a shelter is required, it must have

broad openings on all 4 sides and installation

clearances must be observed.

• Choose the location of the appliance after discussion

with the client.

• We recommend choosing a site that is sunny but

sheltered from strong cold prevailing winds.

• The unit must be easily accessible for future installation

and maintenance work (page 20).

• Ensure that connections to the hydraulic unit can be

made easily.

• The outdoor unit is able to withstand bad weather but

avoid installing it in a position where it is likely to be

exposed to signicant dirt or owing water (under a

defective gutter for example).

Waterstage / Installation / 2016 - EN

- 19 -

• The surface on which the appliance is installed must:

- Be permeable (soil, gravel, etc.).

- Support its weight easily.

- Allow a solid fastening base,

- Not transmit any vibration to the dwelling. Anti-vibratory

blocks are available as an option.

• The wall bracket cannot be used where it is likely to

transmit vibrations. Installing the unit on the ground is

preferred.

▼

Positioning Outdoor Unit

The outdoor unit must be raised at least 50 mm above

ground level. In areas prone to snow, this height should

be increased but should not exceed 1.5 m (gure 12).

- Fasten the outdoor unit by means of screws and

rubber tightening or toothed lock washers to prevent

them from coming loose.

In areas with heavy snowfall, if the intake and

outlet of the outdoor unit is blocked with snow,

heating may become dicult and a failure is

likely to occur.

Construct a canopy or place the unit on a high stand

(local conguration).

- Place the unit on a solid stand in order to minimise

impacts and vibrations.

- Do not place the unit directly on the ground as this will

cause problems.

▼

Condensate drain pipe

The outdoor unit can generate a large volume

of water (called condensate).

If the use of a drain pipe is necessary:

- Use the elbow provided (C) and connect a 16 mm-

diameter hose for draining the condensate.

- Use the plug(s) provided (B) to block the opening of

the condensate drain pan.

Allow for the condensate to ow away under the force of

gravity (waste water, rain water, gravel bed).

If installation is carried out in an area where the

temperature stays below 0°C for long periods,

equip the drain pipe with trace heating to

avoid it icing up. Trace heating must heat not

only the drain pipe but also the bottom of the

appliance's condensate collection tank.

H

Air

g. 14 - Installation of the outdoor unit evacuation of

condensates

* In areas with heavy snowfall,

(H) must be higher than the average snow layer.

B

C

4 holes

(ø 12 mm)

Waterstage / Installation / 2016 - EN

- 20 -

►

Installation of the hydraulic unit

▼

Installation precautions

• Choose the location of the appliance after discussion

with the client.

• The installation space should comply with current

regulations.

• To facilitate maintenance and allow access to the

various parts, we recommend that you provide

sucient space all the way around the hydraulic unit.

350 mm

mini

1000 mm

300 mm

mini

• In accordance with EN 378-1 -2017 standard

(Refrigerating systems and heat pumps - Safety and

environmental requirements), the system's hydraulic

unit and all refrigeration connections passing through

inhabited areas must comply with the minimum room

volume requirements shown hereafter.

The minimum volume of a room (in m

3

) is calculated

using the formula: "uid ll load" (in kg) / 0.39.

Alternatively, you must ensure that

- The location has natural ventilation through another

room where the combined volume of the two rooms

is greater than "liquid ll load" (in kg) / 0.39 kg/m³.

The opening between the two rooms must have a door

clearance of at least 1 cm.

- Or that the location is mechanically ventilated.

Be careful not to bring ammable gas

near the heat pump during installation,

in particular when brazing is required.

The appliances are not reproof and should

not therefore be installed in an explosive

environment.

- To avoid condensation inside the condenser, remove

the refrigeration circuit caps only when making the

refrigeration connections.

- If the refrigeration connection is only performed at the

end of the installation, make sure that the refrigeration

circuit caps* remain in place and tight throughout the

installation.

* (Hydraulic unit side and outdoor unit side).

- After each maintenance operation on the refrigeration

circuit and before the nal connection, take care to

put the caps back in position to avoid any pollution

of the refrigeration circuit (sealing with adhesive is

prohibited).

▼

Positioning the hydraulic unit

- Fix the bracket S securely (4 screws and plugs) to a

strong, at wall (not a light partition) ensuring that it is

correctly levelled.

g. 15 - Mounting bracket

118 mm

(S)

538 mm

mini

418 mm

mini

300 mm

mini

350 mm

mini

188 mm

min.

- Hook the appliance onto its bracket S.

Weight of the appliance (full of water) = 58Kg

Waterstage / Installation / 2016 - EN

Page is loading ...

Fujitsu WSHG160DJ6/WOHG160LJL Installation guide

Related papers

Other documents